Configuring version 3.5 (for Linux) with some most common soundcards
====================================================================

IMPORTANT!	This document covers only cards that were "known" when
		this driver version was released. Please look at
		http://personal.eunet.fi/pp/voxware for info about
		cards introduced recently.

Cards that are not (fully) supported by this driver
---------------------------------------------------

There are many soundcards which don't work with this driver
version (v3.5). Support for some of them is expected to be
available during/after summer 1996 (in version 3.6). Please check
http://personal.eunet.fi/pp/voxware for latest news. Please don't
mail me and ask about these cards. The unsupported cards are:

	- All PnP soundcards (SB PnP, GUS PnP, Soundscape PnP etc.)
		(SB PnP in first 3.6-alpha version (Apr 96?), GUS PnP bit later,
		Soundscape PnP probably much later, others ???). See
	 	"Configuring PnP soundcards" below for some hints.
	- Mwave soundcards and motherboards
		(Version 3.6 or 3.7. Depends on how fast I get a Mwave
		card and suitable documents for it).
	- Emu8k (SB 32/AWE)
		(Probably not before Nov/Dec 96. I know the unofficial
		AWE programmers guide so don't send me more copies of it).
	- Diamond Edge 3D
		(ASAP. In practice this may take relatively long time).
	- Compaq Deskpro
		(Version 3.6???)
	- Miro soundcards
		(Early 3.6-alpha versions)
	- OPTi 82C930 based soundcards
		(Early 3.6-alpha versions?)
	- Sound Galaxy Washington/Waverider
		(3.6-alpha versions. Can't promise the waverider synth).
	- Yamaha OPL4 (on cards having _RAM_ for samples)
		(Late 96?. Works as OPL3 with current driver versions)

How to use sound without recompiling kernel and/or sound driver
---------------------------------------------------------------

There is commercial sound driver which should be released during Apr 96.
It comes in precompiled form and doesn't require recompiling of kernel. See
http://www.4Front-tech.com/uss.html for more info.

Configuring PnP cards
---------------------

New versions of most soundcards use so called ISA PnP protocol for
soft configuring their I/O, IRQ, DMA and shared memory resources.
Currently at least cards made by Creative Technology (SB32 and SB32AWE
PnP), Gravis (GUS PnP and GUS PnP Pro), Ensoniq (Soundscape PnP) and
Aztech (some Sound Galaxy models) use PnP technology. The CS4232 audio
chip by Crystal Semiconductor (Intel Atlantis, HP Pavillon and many other
motherboards) is also based on PnP technology but there is a "native" driver
available for it (see information about CS4232 later in this document).

PnP soundcards (as well as most other PnP ISA cards) are not supported
by version 3.5 of this driver (Linux 1.3.xx and Linux 2.0.x). Proper
support for them should be released during spring 96 
(see http://personal.eunet.fi/pp/voxware for latest info).

There is a method to get most of the PnP cards to work. The basic method
is the following:

1) Boot DOS so that card's DOS drivers have chance to initialize the
card.
2) _Cold_ boot to Linux by using "loadlin.exe". Hitting ctrl-alt-del
works with older machines but causes hard reset of all cards on latest
(Pentium) machines.
3) If you have sound driver in Linux configured properly, the card should work
now. "Proper" means here that I/O, IRQ and DMA settings are the same than in
DOS. The hard part is to find which settings were used. See documentation of
your card for more info.

Windows 95 could work as well as DOS but running loadlin may be somehow 
difficult. Probably you should "shut down" your machine to MS-DOS mode
before running it.

Some machines have BIOS utility for setting PnP resources. This is a good
way to configure some cards. In this case you don't need to boot DOS/Win95
prior starting Linux.
Another way to initialize PnP cards without DOS/Win95 is a Linux based
PnP isolation tool. When writing this there is a pre alpha test version
of such tool available from ftp://ftp.demon.co.uk/pub/unix/linux/utils. The
file is called isapnptools-*. Please note that this tool is just a temporary
solution which may be incompatible with future kernel versions having proper
support for PnP cards.
These two methods don't work with GUS PnP which requires some additional
initialization (cards DOS/Win95 driver does it). 

Read this before trying to configure the driver
-----------------------------------------------

There are currently many cards that work with this driver. Some of the cards
have native support while others work since they emulate some other
card (usually SB, MSS/WSS and/or MPU401). The following cards have native
support in the driver. Detailed instructions for configuring these cards
will be given later in this document.

Pro Audio Spectrum 16 (PAS16) and compatibles:
	Pro Audio Spectrum 16
	Pro Audio Studio 16
	Logitech Sound Man 16
	NOTE! The original Pro Audio Spectrum as well as the PAS+ are not
	      and will not be supported by the driver.

Media Vision Jazz16 based cards
	Pro Sonic 16
	Logitech SoundMan Wave
	(Other Jazz based cards should work but I don't have any reports
	about them).

Sound Blasters
	SB 1.0 to 2.0
	SB Pro
	SB 16
	NOTE!	The ASP chip and the EMU synth of AWE32 are not supported 
		since their manufacturer doesn't release information about
		the card. However, both SB16ASP and AWE32 work with
		the driver just like a SB16. Also see the comment about some
		unsupported cards at the end of this file.
		(The OPL3 FM chip of SB32/AWE works but you cannot hear it).
	SB16 compatible cards by other manufacturers than Creative.
		You have been fooled since there are no SB16 compatible
		cards on the market (Feb 96). It's likely that your card
		is compatible just with SB Pro but there is also a non-SB-
		compatible 16 bit mode. Usually it's MSS/WSS but it could also
		be a proprietary one like MV Jazz16 or ESS ES688.

Gravis Ultrasound (GUS)
	GUS
	GUS + the 16 bit option
	GUS MAX
	GUS ACE (No MIDI port and audio recording)
	GUS PnP (Partially supported)

MPU-401	and compatibles
	The driver works both with the full (intelligent mode) MPU-401
	cards (such as MPU IPC-T and MQX-32M) and with the UART only
	dumb MIDI ports. MPU-401 is currently the most common MIDI
	interface. Most soundcards are compatible with it. However,
	don't enable MPU401 mode blindly. Many cards with native support
	in the driver have their own MPU401 driver. Enabling the standard one
	will cause a conflict with these cards. So check if your card is
	in the list of supported cards before enabling MPU401.

Windows Sound System (MSS/WSS)
	Even when Microsoft has discontinued their own Sound System card 
	they managed to make it a standard. MSS compatible cards are based on 
	a codec chip which is easily available from at least two manufacturers
	(AD1848 by Analog Devices and CS4231/CS4248 by Crystal Semiconductor).
	Currently most soundcards are based on one of the MSS compatible codec
	chips. The CS4231 is used in the high quality cards such as GUS MAX,
	MediaTriX AudioTriX Pro and TB Tropez (GUS MAX is not MSS compatible). 

	Having a AD1848, CS4248 or CS4231 codec chip on the card is a good
	sign. Even if the card is not MSS compatible, it could be easy to write
	support for it. Note also that most MSS compatible cards
	require special boot time initialization which may not be present
	in the driver. Also, some MSS compatible cards have native support.
	Enabling the MSS support with these cards is likely to
	cause a conflict. So check if your card is listed in this file before
	enabling the MSS support.

6850 UART MIDI
	This UART chip is used in the MIDI interface of some (rare)
	soundcards. It's supported by the driver in case you need it.

Yamaha FM synthesizers (OPL2, OPL3 and OPL4)
	Most soundcards have a FM synthesizer chip. The OPL2 is a 2
	operator chip used in the original AdLib card. Currently it's used
	only in the cheapest (8 bit mono) cards. The OPL3 is a 4 operator 
	FM chip which provides better sound quality and/or more available 
	voices than the OPL2. The OPL4 is a new chip that has an OPL3 and
	a wave table synthesizer packed onto the same chip. The driver supports
	just the OPL3 mode directly. Most cards with an OPL4 (like
	SM Wave and AudioTriX Pro) support the OPL4 mode using MPU401
	emulation. Writing a native OPL4 support is difficult
	since Yamaha doesn't give information about their sample ROM chip.

	Enable the generic OPL2/OPL3 FM synthesizer support if your
	card has a FM chip made by Yamaha. Don't enable it if your card
	has a software (TRS) based FM emulator.

PSS based cards (AD1848 + ADSP-2115 + Echo ESC614 ASIC)
	Analog Devices and Echo Speech have together defined a soundcard
	architecture based on the above chips. The DSP chip is used
	for emulation of SB Pro, FM and General MIDI/MT32.

	There are several cards based on this architecture. The most known
	ones are Orchid SW32 and Cardinal DSP16. 

	The driver supports downloading DSP algorithms to these cards.

MediaTriX AudioTriX Pro
	The ATP card is built around a CS4231 codec and an OPL4 synthesizer
	chips. The OPL4 mode is supported by a microcontroller running a
	General MIDI emulator. There is also a SB 1.5 compatible playback mode.

Ensoniq SoundScape and compatibles
	Ensoniq has designed a soundcard architecture based on the
	OTTO synthesizer chip used in their professional MIDI synthesizers.
	Several companies (including Ensoniq, Reveal and Spea) are selling
	cards based on this architecture.

	NOTE! The new PnP SoundScape is not supported yet.

MAD16 and Mozart based cards
	The Mozart (OAK OTI-601) and MAD16 Pro (OPTi 82C929) interface
	chips are used in many different soundcards, including some
	cards by Reveal and Turtle Beach (Tropez). The purpose of these
	chips is to connect other audio components to the PC bus. The
	interface chip performs address decoding for the other chips.
	NOTE! Tropez Plus is not MAD16 but CS4232 based.

Audio Excell DSP16 
	Support for this card was written by Riccardo Faccetti
	(riccardo@cdc8g5.cdc.polimi.it). See aedsp16.c for more info.
	(This driver is not functional in version 3.5 of this driver. A
	patch should be made available during April 96 (sunsite.unc.edu)).
	
Crystal CS4232 based cards such as AcerMagic S23, TB Tropez _Plus_ and 
	many PC motherboards (Compaq, HP, Intel, ...)
	CS4232 is a PnP multimedia chip which contains a CS3231A codec,
	SB and MPU401 emulations. There is support for OPL3 too.
	This is a temporary driver which uses the chip in non PnP mode
	(The final driver should be included in version 3.6 of the driver).
	Unfortunately the MPU401 mode doesn't work (I don't know how to
	initialize it). 

Turtle Beach Maui and Tropez
	This driver version supports sample, patch and program loading commands
	described in the Maui/Tropez User's manual. 
	There is now full initialization support too. The audio side of
	the Tropez is based on the MAD16 chip (see above).

Jumpers and software configuration
----------------------------------

Some of the earliest soundcards were jumper configurable. You have to
configure the driver use I/O, IRQ and DMA settings
that match the jumpers. Just few 8 bit cards are fully jumper 
configurable (SB 1.x/2.x, SB Pro and clones).
Some cards made by Aztech have an EEPROM which contains the 
config info. These cards behave much like hardware jumpered cards.

Most cards have jumper for the base I/O address but other parameters
are software configurable. Sometimes there are few other jumpers too.

Latest cards are fully software configurable or they are PnP ISA
compatible. There are no jumpers on the board.

The driver handles software configurable cards automatically. Just configure
the driver to use I/O, IRQ and DMA settings which are known to work.
You could usually use the same values than with DOS and/or Windows.
Using different settings is possible but not recommended since it may cause
some trouble (for example when warm booting from an OS to another or
when installing new hardware to the machine).

Sound driver sets the soft configurable parameters of the card automatically
during boot. Usually you don't need to run any extra initialization
programs when booting Linux but there are some exceptions. See the
card specific instructions (below) for more info.

The drawback of software configuration is that the driver needs to know
how the card must be initialized. It cannot initialize unknown cards
even if they are otherwise compatible with some other cards (like SB,
MPU401 or Windows Sound System).

What if your card was not listed above?
---------------------------------------

The first thing to do is to look at the major IC chips on the card.
Many of the latest soundcards are based on some standard chips. If you
are lucky, all of them could be supported by the driver. The most common ones
are the OPTi MAD16, Mozart, SoundScape (Ensoniq) and the PSS architectures
listed above. Also look at the end of this file for list of unsupported
cards and the ones which could be supported later.

The last resort is to send _exact_ name and model information of the card
to me together with a list of the major IC chips (manufactured, model) to 
me. I could then try to check if your card looks like something familiar.

There are much more cards in the word than listed above. The first thing to
do with these cards is to check if they emulate some other card/interface
such as SB, MSS and/or MPU401. In this case there is a chance to get the
card to work by booting DOS before starting Linux (boot DOS, hit ctrl-alt-del
and boot Linux without hard resetting the machine). In this method the
DOS based driver initializes the hardware to use a known I/O, IRQ and DMA
settings. If sound driver is configured to use the same settings, everything should 
work OK.


Configuring sound driver (with Linux)
=====================================

Sound driver is currently a part of Linux kernel distribution. The 
driver files are located in directory /usr/src/linux/drivers/sound. 

****************************************************************************
*	ALWAYS USE THE SOUND DRIVER VERSION WHICH IS DISTRIBUTED WITH	   *
*	THE KERNEL SOURCE PACKAGE YOU ARE USING. SOME ALPHA AND BETA TEST  *
*	VERSIONS CAN BE INSTALLED FROM A SEPARATELY DISTRIBUTED PACKAGE	   *
*	BUT CHECK THAT THE PACKAGE IS NOT MUCH OLDER (OR NEWER) THAN THE   *
*	KERNEL YOU ARE USING. IT'S POSSIBLE THAT THE KERNEL/DRIVER 	   *
*	INTERFACE CHANGES BETWEEN KERNEL RELEASES WHICH MAY CAUSE SOME	   *
*	INCOMPATIBILITY PROBLEMS.					   *
*									   *
*	IN CASE YOU INSTALL A SEPARATELY DISTRIBUTED SOUND DRIVER VERSION, *
*	BE SURE TO REMOVE OR RENAME THE OLD SOUND DRIVER DIRECTORY BEFORE  *
*	INSTALLING THE NEW ONE. LEAVING OLD FILES TO THE SOUND DRIVER	   *
*	DIRECTORY _WILL_ CAUSE PROBLEMS WHEN THE DRIVER IS USED OR	   *
*	COMPILED.							   *
****************************************************************************

To configure the driver, run "make config" in the kernel source directory
(/usr/src/linux). Answer y to the question about Sound card support (after
questions about mouse, CD-ROM, ftape, etc. supports). Sound config options
will then be asked after some additional questions.

After configuring the kernel and sound driver, run "make dep" and compile
the kernel following instructions in the kernel README.

The sound driver configuration dialog
-------------------------------------

All config information of the sound driver is written to file 
linux/drivers/sound/local.h. You may save the old version is this file and
use it again in case you want to use the same config later. In this case
just answer n to each question made by the sound config program and put
the original local.h back before running "make dep".
Don't do this if the version number of the sound driver has changed. In this
case you have to enter the configuration information again.

If you already have the sound driver installed, consult printout of
"cat /dev/sndstat" when configuring the driver again. It gives the I/O,
IRQ and DMA settings you have used earlier.


The sound config program (linux/drivers/sound/configure) starts by making
some yes/no questions. Be careful when answering to these questions since
answering y to a question may prevent some later ones from being asked. For
example don't answer y to the first question (PAS16) if you don't really
have a PAS16. Don't enable more cards than you really need since they
just consume memory. Also some drivers (like MPU401) may conflict with your
SCSI controller and prevent kernel from booting. If you card was in the list
of supported cards (above), please look at the card specific config 
instructions (later in this file) before starting to configure. Some cards
must be configured in way which is not obvious.

So here is the beginning of the config dialog. Answer 'y' or 'n' to these
questions. The default answer is shown so that (y/n) means 'y' by default and
(n/y) means 'n'. To use the default value, just hit ENTER. But be careful
since using the default _doesn't_ guarantee anything.

Note also that all questions may not be asked. The configuration program
may disable some questions depending on the earlier choices. It may also
select some options automatically as well.

  "ProAudioSpectrum 16 support",
	- Answer 'y'_ONLY_ if you have a Pro Audio Spectrum _16_,
	  ProAudio Studio 16 or Logitech SoundMan 16 (be sure that
	  you read the above list correctly). Don't answer 'y' if you
	  have some other card made by Media Vision or Logitech since they
	  are not PAS16 compatible.
	  NOTE! Since 3.5-beta10 you need to enable SB support (next question)
	  if you want to use the SB emulation of PAS16. It's also possible to
   	  the emulation if you want to use a true SB card together with PAS16
	  (there is another question about this that is asked later).
  "SoundBlaster support",
	- Answer 'y' if you have an original SB card made by Creative Labs
	  or a full 100% hardware compatible clone (like Thunderboard or
	  SM Games). If your card was in the list of supported cards (above),
	  please look at the card specific instructions later in this file
	  before answering this question. For an unknown card you may answer 
	  'y' if the card claims to be SB compatible.
	 Enable this option also with PAS16 (changed since v3.5-beta9).

	 Don't enable SB if you have a MAD16 or Mozart compatible card.

  "Generic OPL2/OPL3 FM synthesizer support",
	- Answer 'y' if your card has a FM chip made by Yamaha (OPL2/OPL3/OPL4).
	  Answering 'y' is usually a safe and recommended choice. However some
	  cards may have software (TSR) FM emulation. Enabling FM support
	  with these cards may cause trouble. However I don't currently know
	  such cards.
  "Gravis Ultrasound support",
	- Answer 'y' if you have GUS or GUS MAX. Answer 'n' if you don't
	  have GUS since the GUS driver consumes much memory.
	  Currently I don't have experiences with the GUS ACE so I don't
	  know what to answer with it.
  "MPU-401 support (NOT for SB16)",
	- Be careful with this question. The MPU401 interface is supported
	  by almost any soundcard today. However some natively supported cards
	  have their own driver for MPU401. Enabling the MPU401 option with
	  these cards will cause a conflict. Also enabling MPU401 on a system
	  that doesn't really have a MPU401 could cause some trouble. If your
	  card was in the list of supported cards (above), please look at
	  the card specific instructions later in this file.
	  It's safe to answer 'y' if you have a true MPU401 MIDI interface
	  card.
  "6850 UART Midi support",
	- It's safe to answer 'n' to this question in all cases. The 6850
	  UART interface is so rarely used.
  "PSS (ECHO-ADI2111) support",
	- Answer 'y' only if you have Orchid SW32, Cardinal DSP16 or some
	  other card based on the PSS chipset (AD1848 codec + ADSP-2115
	  DSP chip + Echo ESC614 ASIC CHIP).
  "16 bit sampling option of GUS (_NOT_ GUS MAX)",
	- Answer 'y' if you have installed the 16 bit sampling daughtercard
	  to your GUS. Answer 'n' if you have GUS MAX. Enabling this option
	  disables GUS MAX support.
  "GUS MAX support",
	- Answer 'y' only if you have a GUS MAX.
  "Microsoft Sound System support",
	- Again think carefully before answering 'y' to this question. It's
	  safe to answer 'y' in case you have the original Windows Sound 
	  System card made by Microsoft or Aztech SG 16 Pro (or NX16 Pro).
	  Also you may answer 'y' in case your card was not listed earlier
	  in this file. For cards having native support in the driver, consult
	  the card specific instructions later in this file. Some drivers
	  have their own MSS support and enabling this option will cause a
	  conflict.
  "Ensoniq Soundscape support",
	- Answer 'y' if you have a soundcard based on the Ensoniq SoundScape
	  chipset. Such cards are being manufactured at least by Ensoniq,
	  Spea and Reveal (note that Reveal makes other cards also).
  "MediaTriX AudioTriX Pro support",
	- Answer 'y' if you have the AudioTriX Pro.
  "Support for MAD16 and/or Mozart based cards",
	- Answer y if your card has a Mozart (OAK OTI-601) or MAD16
	  (OPTi 82C928 or 82C929) audio interface chip. These chips are
	  currently quite common so it's possible that many no-name cards
	  have one of them. In addition the MAD16 chip is used in some
	  cards made by known manufacturers such as Turtle Beach (Tropez),
	  Reveal (some models) and Diamond (some recent models).
  "Support for TB Maui"
	- This enables TB Maui specific initialization. Works with TB Maui
	and TB Tropez (may not work with Tropez Plus).

  "Audio Excel DSP 16 initialization support",
	- Don't know much about this card. Look at aedsp16.c for more info.

Then the configuration program asks some y/n questions about the higher
level services. It's recommended to answer 'y' to each of these questions.
Answer 'n' only if you know you will not need the option.

  "/dev/dsp and /dev/audio supports (usually required)",
	- Answering 'n' disables /dev/dsp and /dev/audio. Answer 'y'.
  "MIDI interface support",
	- Answering 'n' disables /dev/midi## devices and access to any
	  MIDI ports using /dev/sequencer and /dev/music. This option
	  also affects any MPU401 and/or General MIDI compatible devices.
  "FM synthesizer (YM3812/OPL-3) support",
	- Answer 'y' here.
  "/dev/sequencer support",
	- Answering 'n' disables /dev/sequencer and /dev/music.

Entering the I/O, IRQ and DMA config parameters
-----------------------------------------------

After the above questions the configuration program prompts for the
card specific configuration information. Usually just a set of
I/O address, IRQ and DMA numbers are asked. With some cards the program
asks for some files to be used during initialization of the card. For example
many cards have a DSP chip or microprocessor which must be initialized by
downloading a program (microcode) file to the card. In some cases this file
is written to a .h file by the config program and then included to the driver
during compile.

Instructions for answering these questions are given in the next section.


Card specific information
=========================

This section gives additional instructions about configuring some cards.
Please refer manual of your card for valid I/O, IRQ and DMA numbers. Using
the same settings with DOS/Windows and Linux is recommended. Using
different values could cause some problems when switching between
different operating systems.

SoundBlasters (the original ones by Creative)
---------------------------------------------

It's possible to configure these cards to use different I/O, IRQ and
DMA settings. Since the available settings have changed between various
models, you have to consult manual of your card for the proper ones. It's
a good idea to use the same values than with DOS/Windows. With SB and SB Pro
it's the only choice. SB16 has software selectable IRQ and DMA channels but
using different values with DOS and Linux is likely to cause troubles. The
DOS driver is not able to reset the card properly after warm boot from Linux
if Linux has used different IRQ or DMA values.

The original (steam) Sound Blaster (versions 1.x and 2.x) use always
DMA1. There is no way to change it.

The SB16 needs two DMA channels. A 8 bit one (1 or 3) is required for
8 bit operation and a 16 bit one (5, 6 or 7) for the 16 bit mode. In theory
it's possible to use just one (8 bit) DMA channel by answering the 8 bit
one when the configuration program asks for the 16 bit one. This may work
in some systems but is likely to cause terrible noise on some other systems.

NOTE!	Don't enable the SM Games option (asked by the configuration program)
	if you are not 101% sure that your card is a Logitech Soundman Games
	(not a SM Wave or SM16).

SB Clones
---------

First of all: There are no SB16 clones. There are SB Pro clones with a
16 bit mode which is not SB16 compatible. The most likely alternative is that
the 16 bit mode means MSS/WSS.

There are just few fully 100% hardware SB or SB Pro compatible cards.
I know just Thunderboard and SM Games. Other cards require some kind of
hardware initialization before they become SB compatible. Check if your card
was listed in the beginning of this file. In this case you should follow
instructions for your card later in this file.

For other not fully SB clones you may try initialization using DOS in
the following way:

	- Boot DOS so that the card specific driver gets run.
	- Hit ctrl-alt-del (or use loadlin) to boot Linux. Don't
	  switch off power or press the reset button.
	- If you use the same I/O, IRQ and DMA settings in Linux, the
	  card should work.

If your card is both SB and MSS compatible, I recommend using the MSS mode.
Most cards of this kind are not able to work in the SB and the MSS mode 
simultaneously. Using the MSS mode provides 16 bit recording and playback.

ProAudioSpectrum 16 and compatibles
-----------------------------------

PAS16 has a SB emulation chip which can be used together with the native
(16 bit) mode of the card. To enable this emulation you should configure 
the driver to have SB support too (this has been changed since version
3.5-beta9 of this driver).

With current driver versions it's also possible to use PAS16 together with 
another SB compatible card. In this case you should configure SB support
for the other card and to disable the SB emulation of PAS16 (there is a
separate questions about this).

With PAS16 you can use two audio device files at the same time. /dev/dsp (and
/dev/audio) is connected to the 8/16 bit native codec and the /dev/dsp1 (and
/dev/audio1) is connected to the SB emulation (8 bit mono only).

Gravis Ultrasound
-----------------

There are many different revisions of the Ultrasound card (GUS). The
earliest ones (pre 3.7) don't have a hardware mixer. With these cards
the driver uses a software emulation for synth and pcm playbacks. It's
also possible to switch some of the inputs (line in, mic) off by setting
mixer volume of the channel level below 10%. For recording you have
to select the channel as a recording source and to use volume above 10%.

GUS 3.7 has a hardware mixer.

GUS MAX and the 16 bit sampling daughtercard have a CS4231 codec chip which 
also contains a mixer.

Configuring GUS is simple. Just enable the GUS support and GUS MAX or
the 16 bit daughtercard if you have them. Note that enabling the daughter
card disables GUS MAX driver.

NOTE for owners of the 16 bit daughtercard: By default the daughtercard
uses /dev/dsp (and /dev/audio). Command "ln -sf /dev/dsp1 /dev/dsp"
selects the daughter card as the default device.

With just the standard GUS enabled the configuration program prompts
for the I/O, IRQ and DMA numbers for the card. Use the same values than
with DOS.

With the daughter card option enabled you will be prompted for the I/O,
IRQ and DMA numbers for the daughter card. You have to use different I/O
and DMA values than for the standard GUS. The daughter card permits
simultaneous recording and playback. Use /dev/dsp (the daughtercard) for
recording and /dev/dsp1 (GUS GF1) for playback.

GUS MAX uses the same I/O address and IRQ settings than the original GUS
(GUS MAX = GUS + a CS4231 codec). In addition an extra DMA channel may be used.
Using two DMA channels permits simultaneous playback using two devices
(dev/dsp0 and /dev/dsp1). The second DMA channel is required for
full duplex audio.
To enable the second DMA channels, give a valid DMA channel when the config
program asks for the GUS MAX DMA (entering -1 disables the second DMA).
Using 16 bit DMA channels (5,6 or 7) is recommended.

If you have problems in recording with GUS MAX, you could try to use
just one 8 bit DMA channel. Recording will not work with one DMA
channel if it's a 16 bit one.

Microphone input of GUS MAX is connected to mixer in little bit nonstandard
way. There is actually two microphone volume controls. Normal "mic" controls
only recording level. Mixer control "speaker" is used to control volume of
microphone signal connected directly to line/speaker out. So just decrease
volume of "speaker" if you have problems with microphone feedback.

GUS ACE works too but any attempt to record or to use the MIDI port
will fail.

GUS PnP (with RAM) is partially supported but it needs to be initialized using
DOS before booting Linux. This may fail on machines having PnP BIOS.

MPU401 and Windows Sound System
-------------------------------

Again. Don't enable these options in case your card is listed
somewhere else in this file.

Configuring these cards is obvious (or it should be). With MSS
you should probably enable the OPL3 synth also since
most MSS compatible cards have it. However check that this is true
before enabling OPL3.

Sound driver supports more than one MPU401 compatible cards at the same time
but the config program asks config info for just the first of them.
Adding the second or third MPU interfaces must be done manually by
editing sound/local.h (after running the config program). Add defines for
MPU2_BASE & MPU2_IRQ (and MPU3_BASE & MPU3_IRQ) to the file.

CAUTION!

The default I/O base of Adaptec AHA-1542 SCSI controller is 0x330 which
is also the default of the MPU401 driver. Don't configure the sound driver to
use 0x330 as the MPU401 base if you have a AHA1542. The kernel will not boot
if you make this mistake.

PSS
---

Even the PSS cards are compatible with SB, MSS and MPU401, you must not
enable these options when configuring the driver. The configuration
program handles these options itself. (You may use the SB, MPU and MSS options
together with PSS if you have another card on the system).

The PSS driver enables MSS and MPU401 modes of the card. SB is not enabled 
since it doesn't work concurrently with MSS. The driver loads also a
DSP algorithm which is used to for the general MIDI emulation. The
algorithm file (.ld) is read by the config program and written to a
file included when the pss.c is compiled. For this reason the config
program asks if you want to download the file. Use the genmidi.ld file
distributed with the DOS/Windows drivers of the card (don't use the mt32.ld).
With some cards the file is called 'synth.ld'. You must have access to
the file when configuring the driver. The easiest way is to mount the DOS
partition containing the file with Linux. 

It's possible to load your own DSP algorithms and run them with the card.
Look at the directory pss_test of snd-util-3.0.tar.gz for more info.

AudioTriX Pro
-------------

You have to enable the OPL3 and SB (not SB Pro or SB16) drivers in addition
to the native AudioTriX driver. Don't enable MSS or MPU drivers.

Configuring ATP is little bit tricky since it uses so many I/O, IRQ and
DMA numbers. Using the same values than with DOS/Win is a good idea. Don't
attempt to use the same IRQ or DMA channels twice.

The SB mode of ATP is implemented so the the ATP driver just enables SB
in the proper address. The SB driver handles the rest. You have to configure
both the SB driver and the SB mode of ATP to use the same IRQ, DMA and I/O
settings.

Also the ATP has a microcontroller for the General MIDI emulation (OPL4).
For this reason the driver asks for the name of a file containing the
microcode (TRXPRO.HEX). This file is usually located in the directory
where the DOS drivers were installed. You must have access to this file
when configuring the driver. 

If you have the effects daughtercard, it must be initialized by running
the setfx program of snd-util-3.0.tar.gz package. This step is not required
when using the (future) binary distribution version of the driver.

Ensoniq SoundScape
------------------

NOTE!	The new PnP SoundScape is not supported yet.

The SoundScape driver handles initialization of MSS and MPU supports
itself so you don't need to enable other drivers than SoundScape
(enable also the /dev/dsp, /dev/sequencer and MIDI supports).

SoundScape driver uses the MSS compatible codec of the card. It's important
to note that /dev/dsp0 (/dev/dsp is linked to /dev/dsp0 by default)
doesn't work with SoundScape (yet). The 'ssinit' program needs /dev/dsp0 so
that's the reason why it's there. It's possible that 'primary' pcm channel
becomes supported later. Currently the card's firmware doesn't contain
support for it.

With 3.0 of the driver you have to change your system to use /dev/dsp1 by default
so execute: cd /dev;rm dsp;ln -s dsp1 dsp after you have installed driver
version 3.0 (or later) first time.

The configuration program asks two DMA channels and two interrupts. One IRQ
and one DMA is used by the MSS codec. The second IRQ is required for the
MPU401 mode (you have to use different IRQs for both purposes).
The second DMA channel is required for initialization of the microcontroller.
You have to use separate DMA channels.

The SoundScape card has a Motorola microcontroller which must initialized
_after_ boot (the driver doesn't initialize it during boot).
The initialization is done by running the 'ssinit' program which is
distributed in the snd-util-3.0.tar.gz package. You have to edit two
defines in the ssinit.c and then compile the program. You may run ssinit 
manually (after each boot) or add it to /etc/rc.d/rc.local.

The ssinit program needs the microcode file that comes with the DOS/Windows
driver of the card. You will need to use version 1.30.00 or later
of the microcode file (sndscape.co0 or sndscape.co1 depending on
your card model). THE OLD sndscape.cod WILL NOT WORK. IT WILL HANG YOUR
MACHINE. The only way to get the new microcode file is to download
and install the DOS/Windows driver from ftp://ftp.ensoniq.com/pub.

Then you have to select the proper microcode file to use: soundscape.co0
is the right one for most cards and sndscape.co1 is for few (older) cards
made by Reveal and/or Spea. The driver has capability to detect the card
version during boot. Look at the boot log messages in /var/adm/messages
and locate the sound driver initialization message for the SoundScape
card. If the driver displays string <Ensoniq Soundscape (old)>, you have
an old card and you will need to use sndscape.co1. For other cards use
soundscape.co0.

Check /var/adm/messages after running ssinit. The driver prints
the board version after downloading the microcode file. That version
number must match the number in the name of the microcode file (extension).

Running ssinit with a wrong version of the sndscape.co? file is not
dangerous as long as you don't try to use a file called sndscape.cod.
If you have initialized the card using a wrong microcode file (sounds
are terrible), just modify ssinit.c to use another microcode file and try
again. It's possible to use an earlier version of sndscape.co[01] but it
may sound weird.

MAD16 (Pro) and Mozart
----------------------

You need to enable just the MAD16 /Mozart support when configuring
the driver. _Don't_ enable SB, MPU401 or MSS. However you will need the
/dev/audio, /dev/sequencer and MIDI supports.

Mozart and OPTi 82C928 (the original MAD16) chips don't support
MPU401 mode so enter just 0 when the configuration program asks the
MPU/MIDI I/O base. The MAD16 Pro (OPTi 82C929) has MPU401 mode.

TB Tropez is based on the 82C929 chip. It has two MIDI ports.
The one connected to the MAD16 chip is the second one (there is a second
MIDI connector/pins somewhere??). If you have not connected the second MIDI
port, just disable the MIDI port of MAD16. The 'Maui' compatible synth of
Tropez is jumper configurable and not connected to the MAD16 chip.
It can be used by enabling the stand alone MPU401 support but you have
to initialize it by using the MS-DOS SNDSETUP program.

Some MAD16 based cards may cause feedback, whistle or terrible noise if the
line3 mixer channel is turned too high. This happens at least with Shuttle
Sound System. Current driver versions set volume of line3 low enough so
this should not be a problem.

If you have a MAD16 card which have an OPL4 (FM + Wave table) synthesizer
chip (_not_ an OPL3), you have to append line containing #define MAD16_OPL4
to the file linux/drivers/sound/local.h (after running make config).

MAD16 cards having a CS4231 codec support full duplex mode. This mode
can be enabled by configuring the card to use two DMA channels. Possible
DMA channel pairs are: 0&1, 1&0 and 3&0.

MV Jazz (ProSonic)
------------------

The Jazz16 driver is just a hack made to the SB Pro driver. However it works
fairly well. You have to enable SB, SB Pro (_not_ SB16) and MPU401 supports
when configuring the driver. The configuration program asks later if you
want support for MV Jazz16 based cards (after asking SB base address). Answer
'y' here and the driver asks the second (16 bit) DMA channel.

The Jazz16 driver uses the MPU401 driver in a way which will cause
problems if you have another MPU401 compatible card. In this case you must
give address of the Jazz16 based MPU401 interface when the config
program prompts for the MPU401 information. Then look at the MPU401
specific section for instructions about configuring more than one MPU401 cards.

Logitech Soundman Wave
----------------------

Read the above MV Jazz specific instructions first.

The Logitech SoundMan Wave (don't confuse with the SM16 or SM Games) is
a MV Jazz based card which has an additional OPL4 based wave table
synthesizer. The OPL4 chip is handled by an on board microcontroller
which must be initialized during boot. The config program asks if
you have a SM Wave immediately after asking the second DMA channel of jazz16.
If you answer 'y', the config program will ask name of the file containing
code to be loaded to the microcontroller. The file is usually called
MIDI0001.BIN and it's located in the DOS/Windows driver directory. The file
may also be called as TSUNAMI.BIN or something else (older cards?).

The OPL4 synth will be inaccessible without loading the microcontroller code.

Also remember to enable SB MPU401 support if you want to use the OPL4 mode.
(Don't enable the 'normal' MPU401 device as with some earlier driver
versions (pre 3.5-alpha8)).

NOTE!	Don't answer 'y' when the driver asks about SM Games support
	(the next question after the MIDI0001.BIN name). However
	answering 'y' doesn't cause damage your computer so don't panic. 

Sound Galaxies
--------------

There are many different Sound Galaxy cards made by Aztech. The 8 bit
ones are fully SB or SB Pro compatible and there should be no problems
with them. 

The older 16 bit cards (SG Pro16, SG NX Pro16, Nova and Lyra) have
an EEPROM chip for storing the configuration data. There is a microcontroller
which initializes the card to match the EEPROM settings when the machine
is powered on. These cards actually behave just like they have jumpers
for all of the settings. Configure driver for MSS, MPU, SB/SB Pro  and OPL3 
supports with these cards. 

The config program asks if you want support for the mixer of
SG NX Pro. Answer 'y' to these questions if you have one of the above 8 or
16 bit Aztech cards.

There are some new Sound Galaxies in the market. I have no experience with
them so read the card's manual carefully.

ESS ES1688 and ES688 'AudioDrive' based cards
---------------------------------------------

Support for these two ESS chips is embedded in the SB Pro driver.
Configure these cards just like SB Pro. Enable the 'SB MPU401 MIDI port'
if you want to use MIDI features of ES1688. ES688 doesn't have MPU mode
so you don't need to enable it (the driver uses normal SB MIDI automatically
with ES688).

NOTE! ESS cards are not compatible with MSS/WSS.

Reveal cards
------------

There are several different cards made/marketed by Reveal. Some of them
are compatible with SoundScape and some use the MAD16 chip. You may have
to look at the card and try to identify origin of the card.

Diamond
-------

The oldest (Sierra Aria based) soundcards made by Diamond are not supported
(they may work if the card is initialized using DOS). The recent (LX?)
models are based on the MAD16 chip which is supported by the driver.

Audio Excel DSP16
-----------------

Support for this card is currently not functional. A new driver for it
should be available later this year.

PCMCIA cards
------------

Sorry, can't help. Some cards may work and some don't.

TI TM4000M notebooks
--------------------

These computers have a built in sound support based on the Jazz chipset.
Look at the instructions for MV Jazz (above). It's also important to note
that there is something wrong with the mouse port and sound at least on
some TM models. Don't enable the "C&T 82C710 mouse port support" when
configuring Linux. Having it enabled is likely to cause mysterious problems
and kernel failures when sound is used.

Others?
-------

Since there are so many different soundcards, it's likely that I have 
forgotten to mention many of them. Please inform me if you know yet another
card which works with Linux, please inform me (or is anybody else
willing to maintain a database of supported cards (just like in XF86)?).

Cards not supported yet
=======================

Please check which version of sound driver you are using before 
complaining that your card is not supported. It's possible that you are 
using a driver version which was released months before your card was
introduced. Driver's release date is listed after its version number
in "cat /dev/sndstat" printout and in file linux/drivers/sound/soundvers.h.

First of all, there is an easy way to make most soundcards to work
with Linux. Just use the DOS based driver to initialize the card
to a _known_ state. Then use loadlin.exe to boot Linux. If Linux is configured
to use the same I/O, IRQ and DMA numbers than DOS, the card could work.
(ctrl-alt-del can be used in place of loadlin.exe but it doesn't work with
new motherboards). This method works also with all/most PnP soundcards.

Don't get fooled with SB compatibility. Most cards are compatible with
SB but that may require a TSR which is not possible with Linux. If
the card is compatible with MSS, it's a better choice. Some cards
don't work in the SB and MSS modes at the same time.

Then there are cards which are no longer manufactured and/or which
are relatively rarely used (such as the 8 bit ProAudioSpectrum
models). It's extremely unlikely that such cards never get supported.
Adding support for a new card requires much work and increases time
required in maintaining the driver (some changes need to be done
to all low level drivers and be tested too, maybe with multiple
operating systems). For this reason I have made a decision to not support
obsolete cards. It's possible that someone else makes a separately 
distributed driver (diffs) for the card. Version v3.6 will be much more
modular so making separately distributed drivers will be easier with it.
(The bad news is that v3.6 will not be available before summer -96).

Writing a driver for a new card is not possible if there are no 
programming information available about the card. If you don't
find your new card from this file, look from the home page 
(http://personal.eunet.fi/pp/voxware). Then please contact
manufacturer of the card and ask if they have (or are willing to)
released technical details of the card. Do this before contacting me. I
can only answer 'no' if there are no programming information available.

I have made decision to not accept code based on reverse engineering
to the driver. There are three main reasons: First I don't want to break
relationships to sound card manufacturers. The second reason is that
maintaining and supporting a driver without any specs will be a pain.
The third reason is that companies have freedom to refuse selling their
products to other than Windows users.

Some companies don't give low level technical information about their
products to public or at least their require signing a NDA. It's not
possible to implement a freeware driver for them. However it's possible
that support for such cards become available in the commercial version
of this driver (see http://www.4Front-tech.com/uss.html for more info).

There are some common audio chipsets that are not supported yet. For example
Sierra Aria and IBM Mwave. It's possible that these architectures
get some support in future but I can't make any promises. Just look
at the home page (http://personal.eunet.fi/pp/voxware/new_cards.html)
for latest info.

Information about unsupported soundcards and chipsets is welcome as well
as free copies of soundcards, SDKs and operating systems.

If you have any corrections and/or comments, please contact me.

Hannu Savolainen
hannu@voxware.pp.fi
Sound driver's www home page: http://personal.eunet.fi/pp/voxware
                   US mirror: http://www.4Front-Tech.com/usslite