# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/usb/ci-hdrc-usb2.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: USB2 ChipIdea USB controller

maintainers:
  - Xu Yang <xu.yang_2@nxp.com>
  - Peng Fan <peng.fan@nxp.com>

properties:
  compatible:
    oneOf:
      - enum:
          - chipidea,usb2
          - fsl,imx27-usb
          - lsi,zevio-usb
          - nuvoton,npcm750-udc
          - nvidia,tegra20-ehci
          - nvidia,tegra20-udc
          - nvidia,tegra30-ehci
          - nvidia,tegra30-udc
          - nvidia,tegra114-udc
          - nvidia,tegra124-udc
          - qcom,ci-hdrc
      - items:
          - enum:
              - nvidia,tegra114-ehci
              - nvidia,tegra124-ehci
              - nvidia,tegra210-ehci
          - const: nvidia,tegra30-ehci
      - items:
          - enum:
              - fsl,imx23-usb
              - fsl,imx25-usb
              - fsl,imx28-usb
              - fsl,imx35-usb
              - fsl,imx50-usb
              - fsl,imx51-usb
              - fsl,imx53-usb
              - fsl,imx6q-usb
              - fsl,imx6sl-usb
              - fsl,imx6sx-usb
              - fsl,imx6ul-usb
              - fsl,imx7d-usb
              - fsl,vf610-usb
          - const: fsl,imx27-usb
      - items:
          - enum:
              - fsl,imx8dxl-usb
              - fsl,imx8ulp-usb
          - const: fsl,imx7ulp-usb
          - const: fsl,imx6ul-usb
      - items:
          - enum:
              - fsl,imx8mm-usb
              - fsl,imx8mn-usb
          - const: fsl,imx7d-usb
          - const: fsl,imx27-usb
      - items:
          - enum:
              - fsl,imx6sll-usb
              - fsl,imx7ulp-usb
          - const: fsl,imx6ul-usb
          - const: fsl,imx27-usb
      - items:
          - const: xlnx,zynq-usb-2.20a
          - const: chipidea,usb2
      - items:
          - enum:
              - nuvoton,npcm845-udc
          - const: nuvoton,npcm750-udc

  reg:
    minItems: 1
    maxItems: 2

  interrupts:
    minItems: 1
    maxItems: 2

  clocks:
    minItems: 1
    maxItems: 3

  clock-names:
    minItems: 1
    maxItems: 3

  dr_mode: true

  power-domains:
    maxItems: 1

  resets:
    maxItems: 1

  reset-names:
    maxItems: 1

  "#reset-cells":
    const: 1

  phy_type: true

  itc-setting:
    description:
      interrupt threshold control register control, the setting should be
      aligned with ITC bits at register USBCMD.
    $ref: /schemas/types.yaml#/definitions/uint32

  ahb-burst-config:
    description:
      it is vendor dependent, the required value should be aligned with
      AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This property is
      used to change AHB burst configuration, check the chipidea spec for
      meaning of each value. If this property is not existed, it will use
      the reset value.
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0x0
    maximum: 0x7

  tx-burst-size-dword:
    description:
      it is vendor dependent, the tx burst size in dword (4 bytes), This
      register represents the maximum length of a the burst in 32-bit
      words while moving data from system memory to the USB bus, the value
      of this property will only take effect if property "ahb-burst-config"
      is set to 0, if this property is missing the reset default of the
      hardware implementation will be used.
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0x0
    maximum: 0x20

  rx-burst-size-dword:
    description:
      it is vendor dependent, the rx burst size in dword (4 bytes), This
      register represents the maximum length of a the burst in 32-bit words
      while moving data from the USB bus to system memory, the value of
      this property will only take effect if property "ahb-burst-config"
      is set to 0, if this property is missing the reset default of the
      hardware implementation will be used.
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0x0
    maximum: 0x20

  extcon:
    description:
      Phandles to external connector devices. First phandle should point
      to external connector, which provide "USB" cable events, the second
      should point to external connector device, which provide "USB-HOST"
      cable events. If one of the external connector devices is not
      required, empty <0> phandle should be specified.
    $ref: /schemas/types.yaml#/definitions/phandle-array
    minItems: 1
    items:
      - description: vbus extcon
      - description: id extcon

  phy-clkgate-delay-us:
    description:
      The delay time (us) between putting the PHY into low power mode and
      gating the PHY clock.

  non-zero-ttctrl-ttha:
    description:
      After setting this property, the value of register ttctrl.ttha
      will be 0x7f; if not, the value will be 0x0, this is the default
      value. It needs to be very carefully for setting this property, it
      is recommended that consult with your IC engineer before setting
      this value.  On the most of chipidea platforms, the "usage_tt" flag
      at RTL is 0, so this property only affects siTD.

      If this property is not set, the max packet size is 1023 bytes, and
      if the total of packet size for previous transactions are more than
      256 bytes, it can't accept any transactions within this frame. The
      use case is single transaction, but higher frame rate.

      If this property is set, the max packet size is 188 bytes, it can
      handle more transactions than above case, it can accept transactions
      until it considers the left room size within frame is less than 188
      bytes, software needs to make sure it does not send more than 90%
      maximum_periodic_data_per_frame. The use case is multiple
      transactions, but less frame rate.
    type: boolean

  mux-controls:
    description:
      The mux control for toggling host/device output of this controller.
      It's expected that a mux state of 0 indicates device mode and a mux
      state of 1 indicates host mode.
    maxItems: 1

  mux-control-names:
    const: usb_switch

  operating-points-v2:
    description: A phandle to the OPP table containing the performance states.
    $ref: /schemas/types.yaml#/definitions/phandle

  pinctrl-names:
    description:
      Names for optional pin modes in "default", "host", "device".
      In case of HSIC-mode, "idle" and "active" pin modes are mandatory.
      In this case, the "idle" state needs to pull down the data and
      strobe pin and the "active" state needs to pull up the strobe pin.
    oneOf:
      - items:
          - const: idle
          - const: active
      - items:
          - const: default
          - enum:
              - host
              - device
      - items:
          - const: default

  pinctrl-0:
    maxItems: 1

  pinctrl-1:
    maxItems: 1

  phys:
    maxItems: 1

  phy-names:
    const: usb-phy

  phy-select:
    description:
      Phandler of TCSR node with two argument that indicate register
      offset, and phy index
    $ref: /schemas/types.yaml#/definitions/phandle-array
    items:
      - description: phandle to TCSR node
      - description: register offset
      - description: phy index

  vbus-supply:
    description: reference to the VBUS regulator.

  fsl,usbmisc:
    description:
      Phandler of non-core register device, with one argument that
      indicate usb controller index
    $ref: /schemas/types.yaml#/definitions/phandle-array
    items:
      - items:
          - description: phandle to usbmisc node
          - description: index of usb controller

  fsl,anatop:
    description: phandle for the anatop node.
    $ref: /schemas/types.yaml#/definitions/phandle

  disable-over-current:
    type: boolean
    description: disable over current detect

  over-current-active-low:
    type: boolean
    description: over current signal polarity is active low

  over-current-active-high:
    type: boolean
    description:
      Over current signal polarity is active high. It's recommended to
      specify the over current polarity.

  power-active-high:
    type: boolean
    description: power signal polarity is active high

  external-vbus-divider:
    type: boolean
    description: enables off-chip resistor divider for Vbus

  samsung,picophy-pre-emp-curr-control:
    description:
      HS Transmitter Pre-Emphasis Current Control. This signal controls
      the amount of current sourced to the USB_OTG*_DP and USB_OTG*_DN
      pins after a J-to-K or K-to-J transition. The range is from 0x0 to
      0x3, the default value is 0x1. Details can refer to TXPREEMPAMPTUNE0
      bits of USBNC_n_PHY_CFG1.
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0x0
    maximum: 0x3

  samsung,picophy-dc-vol-level-adjust:
    description:
      HS DC Voltage Level Adjustment. Adjust the high-speed transmitter DC
      level voltage. The range is from 0x0 to 0xf, the default value is
      0x3. Details can refer to TXVREFTUNE0 bits of USBNC_n_PHY_CFG1.
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0x0
    maximum: 0xf

  fsl,picophy-rise-fall-time-adjust:
    description:
      HS Transmitter Rise/Fall Time Adjustment. Adjust the rise/fall times
      of the high-speed transmitter waveform. It has no unit. The rise/fall
      time will be increased or decreased by a certain percentage relative
      to design default time. (0:-10%; 1:design default; 2:+15%; 3:+20%)
      Details can refer to TXRISETUNE0 bit of USBNC_n_PHY_CFG1.
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0
    maximum: 3
    default: 1

  usb-phy:
    description: phandle for the PHY device. Use "phys" instead.
    maxItems: 1
    deprecated: true

  fsl,usbphy:
    description: phandle of usb phy that connects to the port. Use "phys" instead.
    $ref: /schemas/types.yaml#/definitions/phandle
    deprecated: true

  nvidia,phy:
    description: phandle of usb phy that connects to the port. Use "phys" instead.
    $ref: /schemas/types.yaml#/definitions/phandle
    deprecated: true

  nvidia,needs-double-reset:
    description: Indicates double reset or not.
    type: boolean
    deprecated: true

  port:
    description:
      Any connector to the data bus of this controller should be modelled
      using the OF graph bindings specified, if the "usb-role-switch"
      property is used.
    $ref: /schemas/graph.yaml#/properties/port

  reset-gpios:
    maxItems: 1

  ulpi:
    type: object
    additionalProperties: false
    patternProperties:
      "^phy(-[0-9])?$":
        description: The phy child node for Qcom chips.
        type: object
        $ref: /schemas/phy/qcom,usb-hs-phy.yaml

dependencies:
  port: [ usb-role-switch ]
  mux-controls: [ mux-control-names ]

required:
  - compatible
  - reg
  - interrupts

allOf:
  - $ref: usb-hcd.yaml#
  - $ref: usb-drd.yaml#
  - if:
      properties:
        phy_type:
          const: hsic
      required:
        - phy_type
    then:
      properties:
        pinctrl-names:
          items:
            - const: idle
            - const: active
    else:
      properties:
        pinctrl-names:
          minItems: 1
          maxItems: 2
          oneOf:
            - items:
                - const: default
                - enum:
                    - host
                    - device
            - items:
                - const: default
  - if:
      properties:
        compatible:
          contains:
            enum:
              - chipidea,usb2
              - lsi,zevio-usb
              - nuvoton,npcm750-udc
              - nvidia,tegra20-udc
              - nvidia,tegra30-udc
              - nvidia,tegra114-udc
              - nvidia,tegra124-udc
              - qcom,ci-hdrc
              - xlnx,zynq-usb-2.20a
    then:
      properties:
        fsl,usbmisc: false
        disable-over-current: false
        over-current-active-low: false
        over-current-active-high: false
        power-active-high: false
        external-vbus-divider: false
        samsung,picophy-pre-emp-curr-control: false
        samsung,picophy-dc-vol-level-adjust: false

unevaluatedProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/arm-gic.h>
    #include <dt-bindings/clock/berlin2.h>

    usb@f7ed0000 {
        compatible = "chipidea,usb2";
        reg = <0xf7ed0000 0x10000>;
        interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
        clocks = <&chip CLKID_USB0>;
        phys = <&usb_phy0>;
        phy-names = "usb-phy";
        vbus-supply = <&reg_usb0_vbus>;
        itc-setting = <0x4>; /* 4 micro-frames */
         /* Incremental burst of unspecified length */
        ahb-burst-config = <0x0>;
        tx-burst-size-dword = <0x10>; /* 64 bytes */
        rx-burst-size-dword = <0x10>;
        extcon = <0>, <&usb_id>;
        phy-clkgate-delay-us = <400>;
        mux-controls = <&usb_switch>;
        mux-control-names = "usb_switch";
    };

  # Example for HSIC:
  - |
    #include <dt-bindings/interrupt-controller/arm-gic.h>
    #include <dt-bindings/clock/imx6qdl-clock.h>

    usb@2184400 {
        compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
        reg = <0x02184400 0x200>;
        interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
        clocks = <&clks IMX6QDL_CLK_USBOH3>;
        fsl,usbphy = <&usbphynop1>;
        fsl,usbmisc = <&usbmisc 2>;
        phy_type = "hsic";
        dr_mode = "host";
        ahb-burst-config = <0x0>;
        tx-burst-size-dword = <0x10>;
        rx-burst-size-dword = <0x10>;
        pinctrl-names = "idle", "active";
        pinctrl-0 = <&pinctrl_usbh2_idle>;
        pinctrl-1 = <&pinctrl_usbh2_active>;
        #address-cells = <1>;
        #size-cells = <0>;

        ethernet@1 {
            compatible = "usb424,9730";
            reg = <1>;
        };
    };

...