Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 | .. SPDX-License-Identifier: GPL-2.0 ====================================== Texas Instruments CPSW ethernet driver ====================================== Multiqueue & CBS & MQPRIO ========================= The cpsw has 3 CBS shapers for each external ports. This document describes MQPRIO and CBS Qdisc offload configuration for cpsw driver based on examples. It potentially can be used in audio video bridging (AVB) and time sensitive networking (TSN). The following examples were tested on AM572x EVM and BBB boards. Test setup ========== Under consideration two examples with AM572x EVM running cpsw driver in dual_emac mode. Several prerequisites: - TX queues must be rated starting from txq0 that has highest priority - Traffic classes are used starting from 0, that has highest priority - CBS shapers should be used with rated queues - The bandwidth for CBS shapers has to be set a little bit more then potential incoming rate, thus, rate of all incoming tx queues has to be a little less - Real rates can differ, due to discreetness - Map skb-priority to txq is not enough, also skb-priority to l2 prio map has to be created with ip or vconfig tool - Any l2/socket prio (0 - 7) for classes can be used, but for simplicity default values are used: 3 and 2 - only 2 classes tested: A and B, but checked and can work with more, maximum allowed 4, but only for 3 rate can be set. Test setup for examples ======================= :: +-------------------------------+ |--+ | | | Workstation0 | |E | MAC 18:03:73:66:87:42 | +-----------------------------+ +--|t | | | | 1 | E | | |h |./tsn_listener -d \ | | Target board: | 0 | t |--+ |0 | 18:03:73:66:87:42 -i eth0 \| | AM572x EVM | 0 | h | | | -s 1500 | | | 0 | 0 | |--+ | | Only 2 classes: |Mb +---| +-------------------------------+ | class A, class B | | | | +---| +-------------------------------+ | | 1 | E | |--+ | | | 0 | t | | | Workstation1 | | | 0 | h |--+ |E | MAC 20:cf:30:85:7d:fd | | |Mb | 1 | +--|t | | +-----------------------------+ |h |./tsn_listener -d \ | |0 | 20:cf:30:85:7d:fd -i eth0 \| | | -s 1500 | |--+ | +-------------------------------+ Example 1: One port tx AVB configuration scheme for target board ---------------------------------------------------------------- (prints and scheme for AM572x evm, applicable for single port boards) - tc - traffic class - txq - transmit queue - p - priority - f - fifo (cpsw fifo) - S - shaper configured :: +------------------------------------------------------------------+ u | +---------------+ +---------------+ +------+ +------+ | s | | | | | | | | | | e | | App 1 | | App 2 | | Apps | | Apps | | r | | Class A | | Class B | | Rest | | Rest | | | | Eth0 | | Eth0 | | Eth0 | | Eth1 | | s | | VLAN100 | | VLAN100 | | | | | | | | p | | 40 Mb/s | | 20 Mb/s | | | | | | | | a | | SO_PRIORITY=3 | | SO_PRIORITY=2 | | | | | | | | c | | | | | | | | | | | | | | e | +---|-----------+ +---|-----------+ +---|--+ +---|--+ | +-----|------------------|------------------|--------|-------------+ +-+ +------------+ | | | | +-----------------+ +--+ | | | | +---|-------|-------------|-----------------------|----------------+ | +----+ +----+ +----+ +----+ +----+ | | | p3 | | p2 | | p1 | | p0 | | p0 | | k | \ / \ / \ / \ / \ / | e | \ / \ / \ / \ / \ / | r | \/ \/ \/ \/ \/ | n | | | | | | e | | | +-----+ | | l | | | | | | | +----+ +----+ +----+ +----+ | s | |tc0 | |tc1 | |tc2 | |tc0 | | p | \ / \ / \ / \ / | a | \ / \ / \ / \ / | c | \/ \/ \/ \/ | e | | | +-----+ | | | | | | | | | | | | | | | | | | | | | | | | +----+ +----+ +----+ +----+ +----+ | | |txq0| |txq1| |txq2| |txq3| |txq4| | | \ / \ / \ / \ / \ / | | \ / \ / \ / \ / \ / | | \/ \/ \/ \/ \/ | | +-|------|------|------|--+ +--|--------------+ | | | | | | | | Eth0.100 | | Eth1 | | +---|------|------|------|------------------------|----------------+ | | | | | p p p p | 3 2 0-1, 4-7 <- L2 priority | | | | | | | | | | | +---|------|------|------|------------------------|----------------+ | | | | | |----------+ | | +----+ +----+ +----+ +----+ +----+ | | |dma7| |dma6| |dma5| |dma4| |dma3| | | \ / \ / \ / \ / \ / | c | \S / \S / \ / \ / \ / | p | \/ \/ \/ \/ \/ | s | | | | +----- | | w | | | | | | | | | | | | | | d | +----+ +----+ +----+p p+----+ | r | | | | | | |o o| | | i | | f3 | | f2 | | f0 |r r| f0 | | v | |tc0 | |tc1 | |tc2 |t t|tc0 | | e | \CBS / \CBS / \CBS /1 2\CBS / | r | \S / \S / \ / \ / | | \/ \/ \/ \/ | +------------------------------------------------------------------+ 1) :: // Add 4 tx queues, for interface Eth0, and 1 tx queue for Eth1 $ ethtool -L eth0 rx 1 tx 5 rx unmodified, ignoring 2) :: // Check if num of queues is set correctly: $ ethtool -l eth0 Channel parameters for eth0: Pre-set maximums: RX: 8 TX: 8 Other: 0 Combined: 0 Current hardware settings: RX: 1 TX: 5 Other: 0 Combined: 0 3) :: // TX queues must be rated starting from 0, so set bws for tx0 and tx1 // Set rates 40 and 20 Mb/s appropriately. // Pay attention, real speed can differ a bit due to discreetness. // Leave last 2 tx queues not rated. $ echo 40 > /sys/class/net/eth0/queues/tx-0/tx_maxrate $ echo 20 > /sys/class/net/eth0/queues/tx-1/tx_maxrate 4) :: // Check maximum rate of tx (cpdma) queues: $ cat /sys/class/net/eth0/queues/tx-*/tx_maxrate 40 20 0 0 0 5) :: // Map skb->priority to traffic class: // 3pri -> tc0, 2pri -> tc1, (0,1,4-7)pri -> tc2 // Map traffic class to transmit queue: // tc0 -> txq0, tc1 -> txq1, tc2 -> (txq2, txq3) $ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \ map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1 5a) :: // As two interface sharing same set of tx queues, assign all traffic // coming to interface Eth1 to separate queue in order to not mix it // with traffic from interface Eth0, so use separate txq to send // packets to Eth1, so all prio -> tc0 and tc0 -> txq4 // Here hw 0, so here still default configuration for eth1 in hw $ tc qdisc replace dev eth1 handle 100: parent root mqprio num_tc 1 \ map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 queues 1@4 hw 0 6) :: // Check classes settings $ tc -g class show dev eth0 +---(100:ffe2) mqprio | +---(100:3) mqprio | +---(100:4) mqprio | +---(100:ffe1) mqprio | +---(100:2) mqprio | +---(100:ffe0) mqprio +---(100:1) mqprio $ tc -g class show dev eth1 +---(100:ffe0) mqprio +---(100:5) mqprio 7) :: // Set rate for class A - 41 Mbit (tc0, txq0) using CBS Qdisc // Set it +1 Mb for reserve (important!) // here only idle slope is important, others arg are ignored // Pay attention, real speed can differ a bit due to discreetness $ tc qdisc add dev eth0 parent 100:1 cbs locredit -1438 \ hicredit 62 sendslope -959000 idleslope 41000 offload 1 net eth0: set FIFO3 bw = 50 8) :: // Set rate for class B - 21 Mbit (tc1, txq1) using CBS Qdisc: // Set it +1 Mb for reserve (important!) $ tc qdisc add dev eth0 parent 100:2 cbs locredit -1468 \ hicredit 65 sendslope -979000 idleslope 21000 offload 1 net eth0: set FIFO2 bw = 30 9) :: // Create vlan 100 to map sk->priority to vlan qos $ ip link add link eth0 name eth0.100 type vlan id 100 8021q: 802.1Q VLAN Support v1.8 8021q: adding VLAN 0 to HW filter on device eth0 8021q: adding VLAN 0 to HW filter on device eth1 net eth0: Adding vlanid 100 to vlan filter 10) :: // Map skb->priority to L2 prio, 1 to 1 $ ip link set eth0.100 type vlan \ egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 11) :: // Check egress map for vlan 100 $ cat /proc/net/vlan/eth0.100 [...] INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 12) :: // Run your appropriate tools with socket option "SO_PRIORITY" // to 3 for class A and/or to 2 for class B // (I took at https://www.spinics.net/lists/netdev/msg460869.html) ./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p3 -s 1500& ./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p2 -s 1500& 13) :: // run your listener on workstation (should be in same vlan) // (I took at https://www.spinics.net/lists/netdev/msg460869.html) ./tsn_listener -d 18:03:73:66:87:42 -i enp5s0 -s 1500 Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39000 kbps 14) :: // Restore default configuration if needed $ ip link del eth0.100 $ tc qdisc del dev eth1 root $ tc qdisc del dev eth0 root net eth0: Prev FIFO2 is shaped net eth0: set FIFO3 bw = 0 net eth0: set FIFO2 bw = 0 $ ethtool -L eth0 rx 1 tx 1 Example 2: Two port tx AVB configuration scheme for target board ---------------------------------------------------------------- (prints and scheme for AM572x evm, for dual emac boards only) :: +------------------------------------------------------------------+ u | +----------+ +----------+ +------+ +----------+ +----------+ | s | | | | | | | | | | | | e | | App 1 | | App 2 | | Apps | | App 3 | | App 4 | | r | | Class A | | Class B | | Rest | | Class B | | Class A | | | | Eth0 | | Eth0 | | | | | Eth1 | | Eth1 | | s | | VLAN100 | | VLAN100 | | | | | VLAN100 | | VLAN100 | | p | | 40 Mb/s | | 20 Mb/s | | | | | 10 Mb/s | | 30 Mb/s | | a | | SO_PRI=3 | | SO_PRI=2 | | | | | SO_PRI=3 | | SO_PRI=2 | | c | | | | | | | | | | | | | | | | | e | +---|------+ +---|------+ +---|--+ +---|------+ +---|------+ | +-----|-------------|-------------|---------|-------------|--------+ +-+ +-------+ | +----------+ +----+ | | +-------+------+ | | | | | | | | +---|-------|-------------|--------------|-------------|-------|---+ | +----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+ | | | p3 | | p2 | | p1 | | p0 | | p0 | | p1 | | p2 | | p3 | | k | \ / \ / \ / \ / \ / \ / \ / \ / | e | \ / \ / \ / \ / \ / \ / \ / \ / | r | \/ \/ \/ \/ \/ \/ \/ \/ | n | | | | | | | | e | | | +----+ +----+ | | | l | | | | | | | | | +----+ +----+ +----+ +----+ +----+ +----+ | s | |tc0 | |tc1 | |tc2 | |tc2 | |tc1 | |tc0 | | p | \ / \ / \ / \ / \ / \ / | a | \ / \ / \ / \ / \ / \ / | c | \/ \/ \/ \/ \/ \/ | e | | | +-----+ +-----+ | | | | | | | | | | | | | | | | | | | | | | | | | | | | E E | | | | | | +----+ +----+ +----+ +----+ t t +----+ +----+ +----+ +----+ | | |txq0| |txq1| |txq4| |txq5| h h |txq6| |txq7| |txq3| |txq2| | | \ / \ / \ / \ / 0 1 \ / \ / \ / \ / | | \ / \ / \ / \ / . . \ / \ / \ / \ / | | \/ \/ \/ \/ 1 1 \/ \/ \/ \/ | | +-|------|------|------|--+ 0 0 +-|------|------|------|--+ | | | | | | | | 0 0 | | | | | | | +---|------|------|------|---------------|------|------|------|----+ | | | | | | | | p p p p p p p p 3 2 0-1, 4-7 <-L2 pri-> 0-1, 4-7 2 3 | | | | | | | | | | | | | | | | +---|------|------|------|---------------|------|------|------|----+ | | | | | | | | | | | +----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+ | | |dma7| |dma6| |dma3| |dma2| |dma1| |dma0| |dma4| |dma5| | | \ / \ / \ / \ / \ / \ / \ / \ / | c | \S / \S / \ / \ / \ / \ / \S / \S / | p | \/ \/ \/ \/ \/ \/ \/ \/ | s | | | | +----- | | | | | w | | | | | +----+ | | | | | | | | | | | | | | d | +----+ +----+ +----+p p+----+ +----+ +----+ | r | | | | | | |o o| | | | | | | i | | f3 | | f2 | | f0 |r CPSW r| f3 | | f2 | | f0 | | v | |tc0 | |tc1 | |tc2 |t t|tc0 | |tc1 | |tc2 | | e | \CBS / \CBS / \CBS /1 2\CBS / \CBS / \CBS / | r | \S / \S / \ / \S / \S / \ / | | \/ \/ \/ \/ \/ \/ | +------------------------------------------------------------------+ ========================================Eth==========================> 1) :: // Add 8 tx queues, for interface Eth0, but they are common, so are accessed // by two interfaces Eth0 and Eth1. $ ethtool -L eth1 rx 1 tx 8 rx unmodified, ignoring 2) :: // Check if num of queues is set correctly: $ ethtool -l eth0 Channel parameters for eth0: Pre-set maximums: RX: 8 TX: 8 Other: 0 Combined: 0 Current hardware settings: RX: 1 TX: 8 Other: 0 Combined: 0 3) :: // TX queues must be rated starting from 0, so set bws for tx0 and tx1 for Eth0 // and for tx2 and tx3 for Eth1. That is, rates 40 and 20 Mb/s appropriately // for Eth0 and 30 and 10 Mb/s for Eth1. // Real speed can differ a bit due to discreetness // Leave last 4 tx queues as not rated $ echo 40 > /sys/class/net/eth0/queues/tx-0/tx_maxrate $ echo 20 > /sys/class/net/eth0/queues/tx-1/tx_maxrate $ echo 30 > /sys/class/net/eth1/queues/tx-2/tx_maxrate $ echo 10 > /sys/class/net/eth1/queues/tx-3/tx_maxrate 4) :: // Check maximum rate of tx (cpdma) queues: $ cat /sys/class/net/eth0/queues/tx-*/tx_maxrate 40 20 30 10 0 0 0 0 5) :: // Map skb->priority to traffic class for Eth0: // 3pri -> tc0, 2pri -> tc1, (0,1,4-7)pri -> tc2 // Map traffic class to transmit queue: // tc0 -> txq0, tc1 -> txq1, tc2 -> (txq4, txq5) $ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \ map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@4 hw 1 6) :: // Check classes settings $ tc -g class show dev eth0 +---(100:ffe2) mqprio | +---(100:5) mqprio | +---(100:6) mqprio | +---(100:ffe1) mqprio | +---(100:2) mqprio | +---(100:ffe0) mqprio +---(100:1) mqprio 7) :: // Set rate for class A - 41 Mbit (tc0, txq0) using CBS Qdisc for Eth0 // here only idle slope is important, others ignored // Real speed can differ a bit due to discreetness $ tc qdisc add dev eth0 parent 100:1 cbs locredit -1470 \ hicredit 62 sendslope -959000 idleslope 41000 offload 1 net eth0: set FIFO3 bw = 50 8) :: // Set rate for class B - 21 Mbit (tc1, txq1) using CBS Qdisc for Eth0 $ tc qdisc add dev eth0 parent 100:2 cbs locredit -1470 \ hicredit 65 sendslope -979000 idleslope 21000 offload 1 net eth0: set FIFO2 bw = 30 9) :: // Create vlan 100 to map sk->priority to vlan qos for Eth0 $ ip link add link eth0 name eth0.100 type vlan id 100 net eth0: Adding vlanid 100 to vlan filter 10) :: // Map skb->priority to L2 prio for Eth0.100, one to one $ ip link set eth0.100 type vlan \ egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 11) :: // Check egress map for vlan 100 $ cat /proc/net/vlan/eth0.100 [...] INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 12) :: // Map skb->priority to traffic class for Eth1: // 3pri -> tc0, 2pri -> tc1, (0,1,4-7)pri -> tc2 // Map traffic class to transmit queue: // tc0 -> txq2, tc1 -> txq3, tc2 -> (txq6, txq7) $ tc qdisc replace dev eth1 handle 100: parent root mqprio num_tc 3 \ map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@2 1@3 2@6 hw 1 13) :: // Check classes settings $ tc -g class show dev eth1 +---(100:ffe2) mqprio | +---(100:7) mqprio | +---(100:8) mqprio | +---(100:ffe1) mqprio | +---(100:4) mqprio | +---(100:ffe0) mqprio +---(100:3) mqprio 14) :: // Set rate for class A - 31 Mbit (tc0, txq2) using CBS Qdisc for Eth1 // here only idle slope is important, others ignored, but calculated // for interface speed - 100Mb for eth1 port. // Set it +1 Mb for reserve (important!) $ tc qdisc add dev eth1 parent 100:3 cbs locredit -1035 \ hicredit 465 sendslope -69000 idleslope 31000 offload 1 net eth1: set FIFO3 bw = 31 15) :: // Set rate for class B - 11 Mbit (tc1, txq3) using CBS Qdisc for Eth1 // Set it +1 Mb for reserve (important!) $ tc qdisc add dev eth1 parent 100:4 cbs locredit -1335 \ hicredit 405 sendslope -89000 idleslope 11000 offload 1 net eth1: set FIFO2 bw = 11 16) :: // Create vlan 100 to map sk->priority to vlan qos for Eth1 $ ip link add link eth1 name eth1.100 type vlan id 100 net eth1: Adding vlanid 100 to vlan filter 17) :: // Map skb->priority to L2 prio for Eth1.100, one to one $ ip link set eth1.100 type vlan \ egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 18) :: // Check egress map for vlan 100 $ cat /proc/net/vlan/eth1.100 [...] INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 19) :: // Run appropriate tools with socket option "SO_PRIORITY" to 3 // for class A and to 2 for class B. For both interfaces ./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p2 -s 1500& ./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p3 -s 1500& ./tsn_talker -d 20:cf:30:85:7d:fd -i eth1.100 -p2 -s 1500& ./tsn_talker -d 20:cf:30:85:7d:fd -i eth1.100 -p3 -s 1500& 20) :: // run your listener on workstation (should be in same vlan) // (I took at https://www.spinics.net/lists/netdev/msg460869.html) ./tsn_listener -d 18:03:73:66:87:42 -i enp5s0 -s 1500 Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39012 kbps Receiving data rate: 39000 kbps 21) :: // Restore default configuration if needed $ ip link del eth1.100 $ ip link del eth0.100 $ tc qdisc del dev eth1 root net eth1: Prev FIFO2 is shaped net eth1: set FIFO3 bw = 0 net eth1: set FIFO2 bw = 0 $ tc qdisc del dev eth0 root net eth0: Prev FIFO2 is shaped net eth0: set FIFO3 bw = 0 net eth0: set FIFO2 bw = 0 $ ethtool -L eth0 rx 1 tx 1 |