// SPDX-License-Identifier: GPL-2.0-only
/*
* LCD/Backlight Driver for Sharp Zaurus Handhelds (various models)
*
* Copyright (c) 2004-2006 Richard Purdie
*
* Based on Sharp's 2.4 Backlight Driver
*
* Copyright (c) 2008 Marvell International Ltd.
* Converted to SPI device based LCD/Backlight device driver
* by Eric Miao <eric.miao@marvell.com>
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/gpio/consumer.h>
#include <linux/fb.h>
#include <linux/lcd.h>
#include <linux/spi/spi.h>
#include <linux/spi/corgi_lcd.h>
#include <linux/slab.h>
#include <asm/mach/sharpsl_param.h>
#define POWER_IS_ON(pwr) ((pwr) <= FB_BLANK_NORMAL)
/* Register Addresses */
#define RESCTL_ADRS 0x00
#define PHACTRL_ADRS 0x01
#define DUTYCTRL_ADRS 0x02
#define POWERREG0_ADRS 0x03
#define POWERREG1_ADRS 0x04
#define GPOR3_ADRS 0x05
#define PICTRL_ADRS 0x06
#define POLCTRL_ADRS 0x07
/* Register Bit Definitions */
#define RESCTL_QVGA 0x01
#define RESCTL_VGA 0x00
#define POWER1_VW_ON 0x01 /* VW Supply FET ON */
#define POWER1_GVSS_ON 0x02 /* GVSS(-8V) Power Supply ON */
#define POWER1_VDD_ON 0x04 /* VDD(8V),SVSS(-4V) Power Supply ON */
#define POWER1_VW_OFF 0x00 /* VW Supply FET OFF */
#define POWER1_GVSS_OFF 0x00 /* GVSS(-8V) Power Supply OFF */
#define POWER1_VDD_OFF 0x00 /* VDD(8V),SVSS(-4V) Power Supply OFF */
#define POWER0_COM_DCLK 0x01 /* COM Voltage DC Bias DAC Serial Data Clock */
#define POWER0_COM_DOUT 0x02 /* COM Voltage DC Bias DAC Serial Data Out */
#define POWER0_DAC_ON 0x04 /* DAC Power Supply ON */
#define POWER0_COM_ON 0x08 /* COM Power Supply ON */
#define POWER0_VCC5_ON 0x10 /* VCC5 Power Supply ON */
#define POWER0_DAC_OFF 0x00 /* DAC Power Supply OFF */
#define POWER0_COM_OFF 0x00 /* COM Power Supply OFF */
#define POWER0_VCC5_OFF 0x00 /* VCC5 Power Supply OFF */
#define PICTRL_INIT_STATE 0x01
#define PICTRL_INIOFF 0x02
#define PICTRL_POWER_DOWN 0x04
#define PICTRL_COM_SIGNAL_OFF 0x08
#define PICTRL_DAC_SIGNAL_OFF 0x10
#define POLCTRL_SYNC_POL_FALL 0x01
#define POLCTRL_EN_POL_FALL 0x02
#define POLCTRL_DATA_POL_FALL 0x04
#define POLCTRL_SYNC_ACT_H 0x08
#define POLCTRL_EN_ACT_L 0x10
#define POLCTRL_SYNC_POL_RISE 0x00
#define POLCTRL_EN_POL_RISE 0x00
#define POLCTRL_DATA_POL_RISE 0x00
#define POLCTRL_SYNC_ACT_L 0x00
#define POLCTRL_EN_ACT_H 0x00
#define PHACTRL_PHASE_MANUAL 0x01
#define DEFAULT_PHAD_QVGA (9)
#define DEFAULT_COMADJ (125)
struct corgi_lcd {
struct spi_device *spi_dev;
struct lcd_device *lcd_dev;
struct backlight_device *bl_dev;
int limit_mask;
int intensity;
int power;
int mode;
char buf[2];
struct gpio_desc *backlight_on;
struct gpio_desc *backlight_cont;
void (*kick_battery)(void);
};
static int corgi_ssp_lcdtg_send(struct corgi_lcd *lcd, int reg, uint8_t val);
static struct corgi_lcd *the_corgi_lcd;
static unsigned long corgibl_flags;
#define CORGIBL_SUSPENDED 0x01
#define CORGIBL_BATTLOW 0x02
/*
* This is only a pseudo I2C interface. We can't use the standard kernel
* routines as the interface is write only. We just assume the data is acked...
*/
static void lcdtg_ssp_i2c_send(struct corgi_lcd *lcd, uint8_t data)
{
corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS, data);
udelay(10);
}
static void lcdtg_i2c_send_bit(struct corgi_lcd *lcd, uint8_t data)
{
lcdtg_ssp_i2c_send(lcd, data);
lcdtg_ssp_i2c_send(lcd, data | POWER0_COM_DCLK);
lcdtg_ssp_i2c_send(lcd, data);
}
static void lcdtg_i2c_send_start(struct corgi_lcd *lcd, uint8_t base)
{
lcdtg_ssp_i2c_send(lcd, base | POWER0_COM_DCLK | POWER0_COM_DOUT);
lcdtg_ssp_i2c_send(lcd, base | POWER0_COM_DCLK);
lcdtg_ssp_i2c_send(lcd, base);
}
static void lcdtg_i2c_send_stop(struct corgi_lcd *lcd, uint8_t base)
{
lcdtg_ssp_i2c_send(lcd, base);
lcdtg_ssp_i2c_send(lcd, base | POWER0_COM_DCLK);
lcdtg_ssp_i2c_send(lcd, base | POWER0_COM_DCLK | POWER0_COM_DOUT);
}
static void lcdtg_i2c_send_byte(struct corgi_lcd *lcd,
uint8_t base, uint8_t data)
{
int i;
for (i = 0; i < 8; i++) {
if (data & 0x80)
lcdtg_i2c_send_bit(lcd, base | POWER0_COM_DOUT);
else
lcdtg_i2c_send_bit(lcd, base);
data <<= 1;
}
}
static void lcdtg_i2c_wait_ack(struct corgi_lcd *lcd, uint8_t base)
{
lcdtg_i2c_send_bit(lcd, base);
}
static void lcdtg_set_common_voltage(struct corgi_lcd *lcd,
uint8_t base_data, uint8_t data)
{
/* Set Common Voltage to M62332FP via I2C */
lcdtg_i2c_send_start(lcd, base_data);
lcdtg_i2c_send_byte(lcd, base_data, 0x9c);
lcdtg_i2c_wait_ack(lcd, base_data);
lcdtg_i2c_send_byte(lcd, base_data, 0x00);
lcdtg_i2c_wait_ack(lcd, base_data);
lcdtg_i2c_send_byte(lcd, base_data, data);
lcdtg_i2c_wait_ack(lcd, base_data);
lcdtg_i2c_send_stop(lcd, base_data);
}
static int corgi_ssp_lcdtg_send(struct corgi_lcd *lcd, int adrs, uint8_t data)
{
struct spi_message msg;
struct spi_transfer xfer = {
.len = 1,
.cs_change = 0,
.tx_buf = lcd->buf,
};
lcd->buf[0] = ((adrs & 0x07) << 5) | (data & 0x1f);
spi_message_init(&msg);
spi_message_add_tail(&xfer, &msg);
return spi_sync(lcd->spi_dev, &msg);
}
/* Set Phase Adjust */
static void lcdtg_set_phadadj(struct corgi_lcd *lcd, int mode)
{
int adj;
switch (mode) {
case CORGI_LCD_MODE_VGA:
/* Setting for VGA */
adj = sharpsl_param.phadadj;
adj = (adj < 0) ? PHACTRL_PHASE_MANUAL :
PHACTRL_PHASE_MANUAL | ((adj & 0xf) << 1);
break;
case CORGI_LCD_MODE_QVGA:
default:
/* Setting for QVGA */
adj = (DEFAULT_PHAD_QVGA << 1) | PHACTRL_PHASE_MANUAL;
break;
}
corgi_ssp_lcdtg_send(lcd, PHACTRL_ADRS, adj);
}
static void corgi_lcd_power_on(struct corgi_lcd *lcd)
{
int comadj;
/* Initialize Internal Logic & Port */
corgi_ssp_lcdtg_send(lcd, PICTRL_ADRS,
PICTRL_POWER_DOWN | PICTRL_INIOFF |
PICTRL_INIT_STATE | PICTRL_COM_SIGNAL_OFF |
PICTRL_DAC_SIGNAL_OFF);
corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_OFF |
POWER0_COM_OFF | POWER0_VCC5_OFF);
corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_OFF);
/* VDD(+8V), SVSS(-4V) ON */
corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_ON);
mdelay(3);
/* DAC ON */
corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_ON |
POWER0_COM_OFF | POWER0_VCC5_OFF);
/* INIB = H, INI = L */
/* PICTL[0] = H , PICTL[1] = PICTL[2] = PICTL[4] = L */
corgi_ssp_lcdtg_send(lcd, PICTRL_ADRS,
PICTRL_INIT_STATE | PICTRL_COM_SIGNAL_OFF);
/* Set Common Voltage */
comadj = sharpsl_param.comadj;
if (comadj < 0)
comadj = DEFAULT_COMADJ;
lcdtg_set_common_voltage(lcd, POWER0_DAC_ON | POWER0_COM_OFF |
POWER0_VCC5_OFF, comadj);
/* VCC5 ON, DAC ON */
corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_ON |
POWER0_COM_OFF | POWER0_VCC5_ON);
/* GVSS(-8V) ON, VDD ON */
corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
POWER1_VW_OFF | POWER1_GVSS_ON | POWER1_VDD_ON);
mdelay(2);
/* COM SIGNAL ON (PICTL[3] = L) */
corgi_ssp_lcdtg_send(lcd, PICTRL_ADRS, PICTRL_INIT_STATE);
/* COM ON, DAC ON, VCC5_ON */
corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_ON |
POWER0_COM_ON | POWER0_VCC5_ON);
/* VW ON, GVSS ON, VDD ON */
corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
POWER1_VW_ON | POWER1_GVSS_ON | POWER1_VDD_ON);
/* Signals output enable */
corgi_ssp_lcdtg_send(lcd, PICTRL_ADRS, 0);
/* Set Phase Adjust */
lcdtg_set_phadadj(lcd, lcd->mode);
/* Initialize for Input Signals from ATI */
corgi_ssp_lcdtg_send(lcd, POLCTRL_ADRS,
POLCTRL_SYNC_POL_RISE | POLCTRL_EN_POL_RISE |
POLCTRL_DATA_POL_RISE | POLCTRL_SYNC_ACT_L |
POLCTRL_EN_ACT_H);
udelay(1000);
switch (lcd->mode) {
case CORGI_LCD_MODE_VGA:
corgi_ssp_lcdtg_send(lcd, RESCTL_ADRS, RESCTL_VGA);
break;
case CORGI_LCD_MODE_QVGA:
default:
corgi_ssp_lcdtg_send(lcd, RESCTL_ADRS, RESCTL_QVGA);
break;
}
}
static void corgi_lcd_power_off(struct corgi_lcd *lcd)
{
/* 60Hz x 2 frame = 16.7msec x 2 = 33.4 msec */
msleep(34);
/* (1)VW OFF */
corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
POWER1_VW_OFF | POWER1_GVSS_ON | POWER1_VDD_ON);
/* (2)COM OFF */
corgi_ssp_lcdtg_send(lcd, PICTRL_ADRS, PICTRL_COM_SIGNAL_OFF);
corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
POWER0_DAC_ON | POWER0_COM_OFF | POWER0_VCC5_ON);
/* (3)Set Common Voltage Bias 0V */
lcdtg_set_common_voltage(lcd, POWER0_DAC_ON | POWER0_COM_OFF |
POWER0_VCC5_ON, 0);
/* (4)GVSS OFF */
corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_ON);
/* (5)VCC5 OFF */
corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
POWER0_DAC_ON | POWER0_COM_OFF | POWER0_VCC5_OFF);
/* (6)Set PDWN, INIOFF, DACOFF */
corgi_ssp_lcdtg_send(lcd, PICTRL_ADRS,
PICTRL_INIOFF | PICTRL_DAC_SIGNAL_OFF |
PICTRL_POWER_DOWN | PICTRL_COM_SIGNAL_OFF);
/* (7)DAC OFF */
corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
POWER0_DAC_OFF | POWER0_COM_OFF | POWER0_VCC5_OFF);
/* (8)VDD OFF */
corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_OFF);
}
static int corgi_lcd_set_mode(struct lcd_device *ld, struct fb_videomode *m)
{
struct corgi_lcd *lcd = lcd_get_data(ld);
int mode = CORGI_LCD_MODE_QVGA;
if (m->xres == 640 || m->xres == 480)
mode = CORGI_LCD_MODE_VGA;
if (lcd->mode == mode)
return 0;
lcdtg_set_phadadj(lcd, mode);
switch (mode) {
case CORGI_LCD_MODE_VGA:
corgi_ssp_lcdtg_send(lcd, RESCTL_ADRS, RESCTL_VGA);
break;
case CORGI_LCD_MODE_QVGA:
default:
corgi_ssp_lcdtg_send(lcd, RESCTL_ADRS, RESCTL_QVGA);
break;
}
lcd->mode = mode;
return 0;
}
static int corgi_lcd_set_power(struct lcd_device *ld, int power)
{
struct corgi_lcd *lcd = lcd_get_data(ld);
if (POWER_IS_ON(power) && !POWER_IS_ON(lcd->power))
corgi_lcd_power_on(lcd);
if (!POWER_IS_ON(power) && POWER_IS_ON(lcd->power))
corgi_lcd_power_off(lcd);
lcd->power = power;
return 0;
}
static int corgi_lcd_get_power(struct lcd_device *ld)
{
struct corgi_lcd *lcd = lcd_get_data(ld);
return lcd->power;
}
static struct lcd_ops corgi_lcd_ops = {
.get_power = corgi_lcd_get_power,
.set_power = corgi_lcd_set_power,
.set_mode = corgi_lcd_set_mode,
};
static int corgi_bl_get_intensity(struct backlight_device *bd)
{
struct corgi_lcd *lcd = bl_get_data(bd);
return lcd->intensity;
}
static int corgi_bl_set_intensity(struct corgi_lcd *lcd, int intensity)
{
int cont;
if (intensity > 0x10)
intensity += 0x10;
corgi_ssp_lcdtg_send(lcd, DUTYCTRL_ADRS, intensity);
/* Bit 5 via GPIO_BACKLIGHT_CONT */
cont = !!(intensity & 0x20);
if (lcd->backlight_cont)
gpiod_set_value_cansleep(lcd->backlight_cont, cont);
if (lcd->backlight_on)
gpiod_set_value_cansleep(lcd->backlight_on, intensity);
if (lcd->kick_battery)
lcd->kick_battery();
lcd->intensity = intensity;
return 0;
}
static int corgi_bl_update_status(struct backlight_device *bd)
{
struct corgi_lcd *lcd = bl_get_data(bd);
int intensity = backlight_get_brightness(bd);
if (corgibl_flags & CORGIBL_SUSPENDED)
intensity = 0;
if ((corgibl_flags & CORGIBL_BATTLOW) && intensity > lcd->limit_mask)
intensity = lcd->limit_mask;
return corgi_bl_set_intensity(lcd, intensity);
}
void corgi_lcd_limit_intensity(int limit)
{
if (limit)
corgibl_flags |= CORGIBL_BATTLOW;
else
corgibl_flags &= ~CORGIBL_BATTLOW;
backlight_update_status(the_corgi_lcd->bl_dev);
}
EXPORT_SYMBOL(corgi_lcd_limit_intensity);
static const struct backlight_ops corgi_bl_ops = {
.get_brightness = corgi_bl_get_intensity,
.update_status = corgi_bl_update_status,
};
#ifdef CONFIG_PM_SLEEP
static int corgi_lcd_suspend(struct device *dev)
{
struct corgi_lcd *lcd = dev_get_drvdata(dev);
corgibl_flags |= CORGIBL_SUSPENDED;
corgi_bl_set_intensity(lcd, 0);
corgi_lcd_set_power(lcd->lcd_dev, FB_BLANK_POWERDOWN);
return 0;
}
static int corgi_lcd_resume(struct device *dev)
{
struct corgi_lcd *lcd = dev_get_drvdata(dev);
corgibl_flags &= ~CORGIBL_SUSPENDED;
corgi_lcd_set_power(lcd->lcd_dev, FB_BLANK_UNBLANK);
backlight_update_status(lcd->bl_dev);
return 0;
}
#endif
static SIMPLE_DEV_PM_OPS(corgi_lcd_pm_ops, corgi_lcd_suspend, corgi_lcd_resume);
static int setup_gpio_backlight(struct corgi_lcd *lcd,
struct corgi_lcd_platform_data *pdata)
{
struct spi_device *spi = lcd->spi_dev;
lcd->backlight_on = devm_gpiod_get_optional(&spi->dev,
"BL_ON", GPIOD_OUT_LOW);
if (IS_ERR(lcd->backlight_on))
return PTR_ERR(lcd->backlight_on);
lcd->backlight_cont = devm_gpiod_get_optional(&spi->dev, "BL_CONT",
GPIOD_OUT_LOW);
if (IS_ERR(lcd->backlight_cont))
return PTR_ERR(lcd->backlight_cont);
return 0;
}
static int corgi_lcd_probe(struct spi_device *spi)
{
struct backlight_properties props;
struct corgi_lcd_platform_data *pdata = dev_get_platdata(&spi->dev);
struct corgi_lcd *lcd;
int ret = 0;
if (pdata == NULL) {
dev_err(&spi->dev, "platform data not available\n");
return -EINVAL;
}
lcd = devm_kzalloc(&spi->dev, sizeof(struct corgi_lcd), GFP_KERNEL);
if (!lcd)
return -ENOMEM;
lcd->spi_dev = spi;
lcd->lcd_dev = devm_lcd_device_register(&spi->dev, "corgi_lcd",
&spi->dev, lcd, &corgi_lcd_ops);
if (IS_ERR(lcd->lcd_dev))
return PTR_ERR(lcd->lcd_dev);
lcd->power = FB_BLANK_POWERDOWN;
lcd->mode = (pdata) ? pdata->init_mode : CORGI_LCD_MODE_VGA;
memset(&props, 0, sizeof(struct backlight_properties));
props.type = BACKLIGHT_RAW;
props.max_brightness = pdata->max_intensity;
lcd->bl_dev = devm_backlight_device_register(&spi->dev, "corgi_bl",
&spi->dev, lcd, &corgi_bl_ops,
&props);
if (IS_ERR(lcd->bl_dev))
return PTR_ERR(lcd->bl_dev);
lcd->bl_dev->props.brightness = pdata->default_intensity;
lcd->bl_dev->props.power = FB_BLANK_UNBLANK;
ret = setup_gpio_backlight(lcd, pdata);
if (ret)
return ret;
lcd->kick_battery = pdata->kick_battery;
spi_set_drvdata(spi, lcd);
corgi_lcd_set_power(lcd->lcd_dev, FB_BLANK_UNBLANK);
backlight_update_status(lcd->bl_dev);
lcd->limit_mask = pdata->limit_mask;
the_corgi_lcd = lcd;
return 0;
}
static void corgi_lcd_remove(struct spi_device *spi)
{
struct corgi_lcd *lcd = spi_get_drvdata(spi);
lcd->bl_dev->props.power = FB_BLANK_UNBLANK;
lcd->bl_dev->props.brightness = 0;
backlight_update_status(lcd->bl_dev);
corgi_lcd_set_power(lcd->lcd_dev, FB_BLANK_POWERDOWN);
}
static struct spi_driver corgi_lcd_driver = {
.driver = {
.name = "corgi-lcd",
.pm = &corgi_lcd_pm_ops,
},
.probe = corgi_lcd_probe,
.remove = corgi_lcd_remove,
};
module_spi_driver(corgi_lcd_driver);
MODULE_DESCRIPTION("LCD and backlight driver for SHARP C7x0/Cxx00");
MODULE_AUTHOR("Eric Miao <eric.miao@marvell.com>");
MODULE_LICENSE("GPL");
MODULE_ALIAS("spi:corgi-lcd");