Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 | /* SPDX-License-Identifier: GPL-2.0-only */ /* * PXA27x standby mode * * Author: David Burrage * * 2005 (c) MontaVista Software, Inc. */ #include <linux/linkage.h> #include <asm/assembler.h> #include "pxa2xx-regs.h" .text #ifdef CONFIG_PXA27x ENTRY(pxa_cpu_standby) ldr r0, =PSSR mov r1, #(PSSR_PH | PSSR_STS) mov r2, #PWRMODE_STANDBY mov r3, #UNCACHED_PHYS_0 @ Read mem context in. ldr ip, [r3] b 1f .align 5 1: mcr p14, 0, r2, c7, c0, 0 @ put the system into Standby str r1, [r0] @ make sure PSSR_PH/STS are clear ret lr #endif #ifdef CONFIG_PXA3xx #define PXA3_MDCNFG 0x0000 #define PXA3_MDCNFG_DMCEN (1 << 30) #define PXA3_DDR_HCAL 0x0060 #define PXA3_DDR_HCAL_HCRNG 0x1f #define PXA3_DDR_HCAL_HCPROG (1 << 28) #define PXA3_DDR_HCAL_HCEN (1 << 31) #define PXA3_DMCIER 0x0070 #define PXA3_DMCIER_EDLP (1 << 29) #define PXA3_DMCISR 0x0078 #define PXA3_RCOMP 0x0100 #define PXA3_RCOMP_SWEVAL (1 << 31) ENTRY(pm_enter_standby_start) mov r1, #0xf6000000 @ DMEMC_REG_BASE (PXA3_MDCNFG) add r1, r1, #0x00100000 /* * Preload the TLB entry for accessing the dynamic memory * controller registers. Note that page table lookups will * fail until the dynamic memory controller has been * reinitialised - and that includes MMU page table walks. * This also means that only the dynamic memory controller * can be reliably accessed in the code following standby. */ ldr r2, [r1] @ Dummy read PXA3_MDCNFG mcr p14, 0, r0, c7, c0, 0 .rept 8 nop .endr ldr r0, [r1, #PXA3_DDR_HCAL] @ Clear (and wait for) HCEN bic r0, r0, #PXA3_DDR_HCAL_HCEN str r0, [r1, #PXA3_DDR_HCAL] 1: ldr r0, [r1, #PXA3_DDR_HCAL] tst r0, #PXA3_DDR_HCAL_HCEN bne 1b ldr r0, [r1, #PXA3_RCOMP] @ Initiate RCOMP orr r0, r0, #PXA3_RCOMP_SWEVAL str r0, [r1, #PXA3_RCOMP] mov r0, #~0 @ Clear interrupts str r0, [r1, #PXA3_DMCISR] ldr r0, [r1, #PXA3_DMCIER] @ set DMIER[EDLP] orr r0, r0, #PXA3_DMCIER_EDLP str r0, [r1, #PXA3_DMCIER] ldr r0, [r1, #PXA3_DDR_HCAL] @ clear HCRNG, set HCPROG, HCEN bic r0, r0, #PXA3_DDR_HCAL_HCRNG orr r0, r0, #PXA3_DDR_HCAL_HCEN | PXA3_DDR_HCAL_HCPROG str r0, [r1, #PXA3_DDR_HCAL] 1: ldr r0, [r1, #PXA3_DMCISR] tst r0, #PXA3_DMCIER_EDLP beq 1b ldr r0, [r1, #PXA3_MDCNFG] @ set PXA3_MDCNFG[DMCEN] orr r0, r0, #PXA3_MDCNFG_DMCEN str r0, [r1, #PXA3_MDCNFG] 1: ldr r0, [r1, #PXA3_MDCNFG] tst r0, #PXA3_MDCNFG_DMCEN beq 1b ldr r0, [r1, #PXA3_DDR_HCAL] @ set PXA3_DDR_HCAL[HCRNG] orr r0, r0, #2 @ HCRNG str r0, [r1, #PXA3_DDR_HCAL] ldr r0, [r1, #PXA3_DMCIER] @ Clear the interrupt bic r0, r0, #0x20000000 str r0, [r1, #PXA3_DMCIER] ret lr ENTRY(pm_enter_standby_end) #endif |