Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 | ======================== Kernel driver for lm3556 ======================== * Texas Instrument: 1.5 A Synchronous Boost LED Flash Driver w/ High-Side Current Source * Datasheet: http://www.national.com/ds/LM/LM3556.pdf Authors: - Daniel Jeong Contact:Daniel Jeong(daniel.jeong-at-ti.com, gshark.jeong-at-gmail.com) Description ----------- There are 3 functions in LM3556, Flash, Torch and Indicator. Flash Mode ^^^^^^^^^^ In Flash Mode, the LED current source(LED) provides 16 target current levels from 93.75 mA to 1500 mA.The Flash currents are adjusted via the CURRENT CONTROL REGISTER(0x09).Flash mode is activated by the ENABLE REGISTER(0x0A), or by pulling the STROBE pin HIGH. LM3556 Flash can be controlled through /sys/class/leds/flash/brightness file * if STROBE pin is enabled, below example control brightness only, and ON / OFF will be controlled by STROBE pin. Flash Example: OFF:: #echo 0 > /sys/class/leds/flash/brightness 93.75 mA:: #echo 1 > /sys/class/leds/flash/brightness ... 1500 mA:: #echo 16 > /sys/class/leds/flash/brightness Torch Mode ^^^^^^^^^^ In Torch Mode, the current source(LED) is programmed via the CURRENT CONTROL REGISTER(0x09).Torch Mode is activated by the ENABLE REGISTER(0x0A) or by the hardware TORCH input. LM3556 torch can be controlled through /sys/class/leds/torch/brightness file. * if TORCH pin is enabled, below example control brightness only, and ON / OFF will be controlled by TORCH pin. Torch Example: OFF:: #echo 0 > /sys/class/leds/torch/brightness 46.88 mA:: #echo 1 > /sys/class/leds/torch/brightness ... 375 mA:: #echo 8 > /sys/class/leds/torch/brightness Indicator Mode ^^^^^^^^^^^^^^ Indicator pattern can be set through /sys/class/leds/indicator/pattern file, and 4 patterns are pre-defined in indicator_pattern array. According to N-lank, Pulse time and N Period values, different pattern wiill be generated.If you want new patterns for your own device, change indicator_pattern array with your own values and INDIC_PATTERN_SIZE. Please refer datasheet for more detail about N-Blank, Pulse time and N Period. Indicator pattern example: pattern 0:: #echo 0 > /sys/class/leds/indicator/pattern ... pattern 3:: #echo 3 > /sys/class/leds/indicator/pattern Indicator brightness can be controlled through sys/class/leds/indicator/brightness file. Example: OFF:: #echo 0 > /sys/class/leds/indicator/brightness 5.86 mA:: #echo 1 > /sys/class/leds/indicator/brightness ... 46.875mA:: #echo 8 > /sys/class/leds/indicator/brightness Notes ----- Driver expects it is registered using the i2c_board_info mechanism. To register the chip at address 0x63 on specific adapter, set the platform data according to include/linux/platform_data/leds-lm3556.h, set the i2c board info Example:: static struct i2c_board_info board_i2c_ch4[] __initdata = { { I2C_BOARD_INFO(LM3556_NAME, 0x63), .platform_data = &lm3556_pdata, }, }; and register it in the platform init function Example:: board_register_i2c_bus(4, 400, board_i2c_ch4, ARRAY_SIZE(board_i2c_ch4)); |