Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 | // SPDX-License-Identifier: (GPL-2.0 OR MIT) /* * Device Tree file for Synology DS116 NAS * * Copyright (C) 2017 Willy Tarreau <w@1wt.eu> */ /dts-v1/; #include "armada-385.dtsi" #include <dt-bindings/gpio/gpio.h> / { model = "Synology DS116"; compatible = "marvell,a385-gp", "marvell,armada385", "marvell,armada380"; chosen { stdout-path = "serial0:115200n8"; }; memory { device_type = "memory"; reg = <0x00000000 0x40000000>; /* 1 GB */ }; soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000 MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000 MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>; internal-regs { i2c@11000 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>; status = "okay"; clock-frequency = <100000>; eeprom@57 { compatible = "atmel,24c64"; reg = <0x57>; }; }; serial@12000 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins>; status = "okay"; }; serial@12100 { /* A PIC16F1829 is connected to uart1 at 9600 bps, * and takes single-character orders : * "1" : power off // already handled by the poweroff node * "2" : short beep * "3" : long beep * "4" : turn the power LED ON * "5" : flash the power LED * "6" : turn the power LED OFF * "7" : turn the status LED OFF * "8" : turn the status LED ON * "9" : flash the status LED * "A" : flash the motherboard LED (D8) * "B" : turn the motherboard LED OFF * "C" : hard reset */ pinctrl-names = "default"; pinctrl-0 = <&uart1_pins>; status = "okay"; }; poweroff@12100 { compatible = "synology,power-off"; reg = <0x12100 0x100>; clocks = <&coreclk 0>; }; ethernet@70000 { pinctrl-names = "default"; phy = <&phy0>; phy-mode = "sgmii"; buffer-manager = <&bm>; bm,pool-long = <0>; status = "okay"; }; mdio@72004 { pinctrl-names = "default"; pinctrl-0 = <&mdio_pins>; phy0: ethernet-phy@1 { reg = <1>; }; }; sata@a8000 { pinctrl-names = "default"; pinctrl-0 = <&sata0_pins>; status = "okay"; #address-cells = <1>; #size-cells = <0>; sata0: sata-port@0 { reg = <0>; target-supply = <®_5v_sata0>; }; }; bm@c8000 { status = "okay"; }; usb3@f0000 { usb-phy = <&usb3_0_phy>; status = "okay"; }; usb3@f8000 { usb-phy = <&usb3_1_phy>; status = "okay"; }; }; bm-bppi { status = "okay"; }; gpio-fan { compatible = "gpio-fan"; gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>, <&gpio1 17 GPIO_ACTIVE_HIGH>, <&gpio1 16 GPIO_ACTIVE_HIGH>; gpio-fan,speed-map = < 0 0 1500 1 2500 2 3000 3 3400 4 3700 5 3900 6 4000 7>; #cooling-cells = <2>; }; gpio-leds { compatible = "gpio-leds"; /* The green part is on gpio0.20 which is also used by * sata0, and accesses to SATA disk 0 make it blink so it * doesn't need to be declared here. */ led-orange { gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; label = "ds116:orange:disk"; default-state = "off"; }; }; }; usb3_0_phy: usb3_0_phy { compatible = "usb-nop-xceiv"; vcc-supply = <®_usb3_0_vbus>; #phy-cells = <0>; }; usb3_1_phy: usb3_1_phy { compatible = "usb-nop-xceiv"; vcc-supply = <®_usb3_1_vbus>; #phy-cells = <0>; }; reg_usb3_0_vbus: usb3-vbus0 { compatible = "regulator-fixed"; regulator-name = "usb3-vbus0"; pinctrl-names = "default"; pinctrl-0 = <&xhci0_vbus_pins>; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; enable-active-high; gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>; }; reg_usb3_1_vbus: usb3-vbus1 { compatible = "regulator-fixed"; regulator-name = "usb3-vbus1"; pinctrl-names = "default"; pinctrl-0 = <&xhci1_vbus_pins>; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; enable-active-high; gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>; }; reg_sata0: pwr-sata0 { compatible = "regulator-fixed"; regulator-name = "pwr_en_sata0"; regulator-min-microvolt = <12000000>; regulator-max-microvolt = <12000000>; enable-active-high; regulator-boot-on; gpio = <&gpio0 15 GPIO_ACTIVE_HIGH>; }; reg_5v_sata0: v5-sata0 { compatible = "regulator-fixed"; regulator-name = "v5.0-sata0"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; vin-supply = <®_sata0>; }; reg_12v_sata0: v12-sata0 { compatible = "regulator-fixed"; regulator-name = "v12.0-sata0"; regulator-min-microvolt = <12000000>; regulator-max-microvolt = <12000000>; vin-supply = <®_sata0>; }; }; &spi0 { pinctrl-names = "default"; pinctrl-0 = <&spi0_pins>; status = "okay"; flash@0 { #address-cells = <1>; #size-cells = <1>; compatible = "macronix,mx25l6405d", "jedec,spi-nor"; reg = <0>; /* Chip select 0 */ spi-max-frequency = <50000000>; m25p,fast-read; /* Note: there is a redboot partition table despite u-boot * being used. The names presented here are the same as those * found in the FIS directory. There is also a small device * tree in the last 64kB of the RedBoot partition which is not * enumerated. The MAC address and the serial number are listed * in the "vendor" partition. */ partition@0 { label = "RedBoot"; reg = <0x00000000 0x000f0000>; read-only; }; partition@c0000 { label = "zImage"; reg = <0x000f0000 0x002d0000>; }; partition@390000 { label = "rd.gz"; reg = <0x003c0000 0x00410000>; }; partition@7d0000 { label = "vendor"; reg = <0x007d0000 0x00010000>; read-only; }; partition@7e0000 { label = "RedBoot config"; reg = <0x007e0000 0x00010000>; read-only; }; partition@7f0000 { label = "FIS directory"; reg = <0x007f0000 0x00010000>; read-only; }; }; }; &pinctrl { /* use only one pin for UART1, as mpp20 is used by sata0 */ uart1_pins: uart-pins-1 { marvell,pins = "mpp19"; marvell,function = "ua1"; }; xhci0_vbus_pins: xhci0_vbus_pins { marvell,pins = "mpp58"; marvell,function = "gpio"; }; xhci1_vbus_pins: xhci1_vbus_pins { marvell,pins = "mpp59"; marvell,function = "gpio"; }; }; |