Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 | # SPDX-License-Identifier: GPL-2.0-only config DRM_MSM tristate "MSM DRM" depends on DRM depends on ARCH_QCOM || SOC_IMX5 || COMPILE_TEST depends on COMMON_CLK depends on IOMMU_SUPPORT depends on QCOM_OCMEM || QCOM_OCMEM=n depends on QCOM_LLCC || QCOM_LLCC=n depends on QCOM_COMMAND_DB || QCOM_COMMAND_DB=n select IOMMU_IO_PGTABLE select QCOM_MDT_LOADER if ARCH_QCOM select REGULATOR select DRM_DP_AUX_BUS select DRM_DISPLAY_DP_HELPER select DRM_DISPLAY_HELPER select DRM_KMS_HELPER select DRM_PANEL select DRM_BRIDGE select DRM_PANEL_BRIDGE select DRM_SCHED select SHMEM select TMPFS select QCOM_SCM select WANT_DEV_COREDUMP select SND_SOC_HDMI_CODEC if SND_SOC select SYNC_FILE select PM_OPP select NVMEM help DRM/KMS driver for MSM/snapdragon. config DRM_MSM_GPU_STATE bool depends on DRM_MSM && (DEBUG_FS || DEV_COREDUMP) default y config DRM_MSM_GPU_SUDO bool "Enable SUDO flag on submits" depends on DRM_MSM && EXPERT default n help Enable userspace that has CAP_SYS_RAWIO to submit GPU commands that are run from RB instead of IB1. This essentially gives userspace kernel level access, but is useful for firmware debugging. Only use this if you are a driver developer. This should *not* be enabled for production kernels. If unsure, say N. config DRM_MSM_MDSS bool depends on DRM_MSM default n config DRM_MSM_MDP4 bool "Enable MDP4 support in MSM DRM driver" depends on DRM_MSM default y help Compile in support for the Mobile Display Processor v4 (MDP4) in the MSM DRM driver. It is the older display controller found in devices using APQ8064/MSM8960/MSM8x60 platforms. config DRM_MSM_MDP5 bool "Enable MDP5 support in MSM DRM driver" depends on DRM_MSM select DRM_MSM_MDSS default y help Compile in support for the Mobile Display Processor v5 (MDP5) in the MSM DRM driver. It is the display controller found in devices using e.g. APQ8016/MSM8916/APQ8096/MSM8996/MSM8974/SDM6x0 platforms. config DRM_MSM_DPU bool "Enable DPU support in MSM DRM driver" depends on DRM_MSM select DRM_MSM_MDSS default y help Compile in support for the Display Processing Unit in the MSM DRM driver. It is the display controller found in devices using e.g. SDM845 and newer platforms. config DRM_MSM_DP bool "Enable DisplayPort support in MSM DRM driver" depends on DRM_MSM select RATIONAL default y help Compile in support for DP driver in MSM DRM driver. DP external display support is enabled through this config option. It can be primary or secondary display on device. config DRM_MSM_DSI bool "Enable DSI support in MSM DRM driver" depends on DRM_MSM select DRM_PANEL select DRM_MIPI_DSI default y help Choose this option if you have a need for MIPI DSI connector support. config DRM_MSM_DSI_28NM_PHY bool "Enable DSI 28nm PHY driver in MSM DRM" depends on DRM_MSM_DSI default y help Choose this option if the 28nm DSI PHY is used on the platform. config DRM_MSM_DSI_20NM_PHY bool "Enable DSI 20nm PHY driver in MSM DRM" depends on DRM_MSM_DSI default y help Choose this option if the 20nm DSI PHY is used on the platform. config DRM_MSM_DSI_28NM_8960_PHY bool "Enable DSI 28nm 8960 PHY driver in MSM DRM" depends on DRM_MSM_DSI default y help Choose this option if the 28nm DSI PHY 8960 variant is used on the platform. config DRM_MSM_DSI_14NM_PHY bool "Enable DSI 14nm PHY driver in MSM DRM (used by MSM8996/APQ8096)" depends on DRM_MSM_DSI default y help Choose this option if DSI PHY on 8996 is used on the platform. config DRM_MSM_DSI_10NM_PHY bool "Enable DSI 10nm PHY driver in MSM DRM (used by SDM845)" depends on DRM_MSM_DSI default y help Choose this option if DSI PHY on SDM845 is used on the platform. config DRM_MSM_DSI_7NM_PHY bool "Enable DSI 7nm/5nm/4nm PHY driver in MSM DRM" depends on DRM_MSM_DSI default y help Choose this option if DSI PHY on SM8150/SM8250/SM8350/SM8450/SM8550/SC7280 is used on the platform. config DRM_MSM_HDMI bool "Enable HDMI support in MSM DRM driver" depends on DRM_MSM default y help Compile in support for the HDMI output MSM DRM driver. It can be a primary or a secondary display on device. Note that this is used only for the direct HDMI output. If the device outputs HDMI data through some kind of DSI-to-HDMI bridge, this option can be disabled. config DRM_MSM_HDMI_HDCP bool "Enable HDMI HDCP support in MSM DRM driver" depends on DRM_MSM && DRM_MSM_HDMI default y help Choose this option to enable HDCP state machine |