/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* Copyright(c) 2008 - 2009 Atheros Corporation. All rights reserved.
*
* Derived from Intel e1000 driver
* Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
*/
#ifndef _ATL1C_HW_H_
#define _ATL1C_HW_H_
#include <linux/types.h>
#include <linux/mii.h>
#define FIELD_GETX(_x, _name) ((_x) >> (_name##_SHIFT) & (_name##_MASK))
#define FIELD_SETX(_x, _name, _v) \
(((_x) & ~((_name##_MASK) << (_name##_SHIFT))) |\
(((_v) & (_name##_MASK)) << (_name##_SHIFT)))
#define FIELDX(_name, _v) (((_v) & (_name##_MASK)) << (_name##_SHIFT))
struct atl1c_adapter;
struct atl1c_hw;
/* function prototype */
void atl1c_phy_disable(struct atl1c_hw *hw);
void atl1c_hw_set_mac_addr(struct atl1c_hw *hw, u8 *mac_addr);
int atl1c_phy_reset(struct atl1c_hw *hw);
int atl1c_read_mac_addr(struct atl1c_hw *hw);
bool atl1c_get_link_status(struct atl1c_hw *hw);
int atl1c_get_speed_and_duplex(struct atl1c_hw *hw, u16 *speed, u16 *duplex);
u32 atl1c_hash_mc_addr(struct atl1c_hw *hw, u8 *mc_addr);
void atl1c_hash_set(struct atl1c_hw *hw, u32 hash_value);
int atl1c_read_phy_reg(struct atl1c_hw *hw, u16 reg_addr, u16 *phy_data);
int atl1c_write_phy_reg(struct atl1c_hw *hw, u32 reg_addr, u16 phy_data);
bool atl1c_read_eeprom(struct atl1c_hw *hw, u32 offset, u32 *p_value);
int atl1c_phy_init(struct atl1c_hw *hw);
int atl1c_check_eeprom_exist(struct atl1c_hw *hw);
int atl1c_restart_autoneg(struct atl1c_hw *hw);
int atl1c_phy_to_ps_link(struct atl1c_hw *hw);
int atl1c_power_saving(struct atl1c_hw *hw, u32 wufc);
bool atl1c_wait_mdio_idle(struct atl1c_hw *hw);
void atl1c_stop_phy_polling(struct atl1c_hw *hw);
void atl1c_start_phy_polling(struct atl1c_hw *hw, u16 clk_sel);
int atl1c_read_phy_core(struct atl1c_hw *hw, bool ext, u8 dev,
u16 reg, u16 *phy_data);
int atl1c_write_phy_core(struct atl1c_hw *hw, bool ext, u8 dev,
u16 reg, u16 phy_data);
int atl1c_read_phy_ext(struct atl1c_hw *hw, u8 dev_addr,
u16 reg_addr, u16 *phy_data);
int atl1c_write_phy_ext(struct atl1c_hw *hw, u8 dev_addr,
u16 reg_addr, u16 phy_data);
int atl1c_read_phy_dbg(struct atl1c_hw *hw, u16 reg_addr, u16 *phy_data);
int atl1c_write_phy_dbg(struct atl1c_hw *hw, u16 reg_addr, u16 phy_data);
void atl1c_post_phy_linkchg(struct atl1c_hw *hw, u16 link_speed);
/* hw-ids */
#define PCI_DEVICE_ID_ATTANSIC_L2C 0x1062
#define PCI_DEVICE_ID_ATTANSIC_L1C 0x1063
#define PCI_DEVICE_ID_ATHEROS_L2C_B 0x2060 /* AR8152 v1.1 Fast 10/100 */
#define PCI_DEVICE_ID_ATHEROS_L2C_B2 0x2062 /* AR8152 v2.0 Fast 10/100 */
#define PCI_DEVICE_ID_ATHEROS_L1D 0x1073 /* AR8151 v1.0 Gigabit 1000 */
#define PCI_DEVICE_ID_ATHEROS_L1D_2_0 0x1083 /* AR8151 v2.0 Gigabit 1000 */
#define L2CB_V10 0xc0
#define L2CB_V11 0xc1
#define L2CB_V20 0xc0
#define L2CB_V21 0xc1
/* register definition */
#define REG_DEVICE_CAP 0x5C
#define DEVICE_CAP_MAX_PAYLOAD_MASK 0x7
#define DEVICE_CAP_MAX_PAYLOAD_SHIFT 0
#define DEVICE_CTRL_MAXRRS_MIN 2
#define REG_LINK_CTRL 0x68
#define LINK_CTRL_L0S_EN 0x01
#define LINK_CTRL_L1_EN 0x02
#define LINK_CTRL_EXT_SYNC 0x80
#define REG_PCIE_IND_ACC_ADDR 0x80
#define REG_PCIE_IND_ACC_DATA 0x84
#define REG_DEV_SERIALNUM_CTRL 0x200
#define REG_DEV_MAC_SEL_MASK 0x0 /* 0:EUI; 1:MAC */
#define REG_DEV_MAC_SEL_SHIFT 0
#define REG_DEV_SERIAL_NUM_EN_MASK 0x1
#define REG_DEV_SERIAL_NUM_EN_SHIFT 1
#define REG_TWSI_CTRL 0x218
#define TWSI_CTLR_FREQ_MASK 0x3UL
#define TWSI_CTRL_FREQ_SHIFT 24
#define TWSI_CTRL_FREQ_100K 0
#define TWSI_CTRL_FREQ_200K 1
#define TWSI_CTRL_FREQ_300K 2
#define TWSI_CTRL_FREQ_400K 3
#define TWSI_CTRL_LD_EXIST BIT(23)
#define TWSI_CTRL_HW_LDSTAT BIT(12) /* 0:finish,1:in progress */
#define TWSI_CTRL_SW_LDSTART BIT(11)
#define TWSI_CTRL_LD_OFFSET_MASK 0xFF
#define TWSI_CTRL_LD_OFFSET_SHIFT 0
#define REG_PCIE_DEV_MISC_CTRL 0x21C
#define PCIE_DEV_MISC_EXT_PIPE 0x2
#define PCIE_DEV_MISC_RETRY_BUFDIS 0x1
#define PCIE_DEV_MISC_SPIROM_EXIST 0x4
#define PCIE_DEV_MISC_SERDES_ENDIAN 0x8
#define PCIE_DEV_MISC_SERDES_SEL_DIN 0x10
#define REG_PCIE_PHYMISC 0x1000
#define PCIE_PHYMISC_FORCE_RCV_DET BIT(2)
#define PCIE_PHYMISC_NFTS_MASK 0xFFUL
#define PCIE_PHYMISC_NFTS_SHIFT 16
#define REG_PCIE_PHYMISC2 0x1004
#define PCIE_PHYMISC2_L0S_TH_MASK 0x3UL
#define PCIE_PHYMISC2_L0S_TH_SHIFT 18
#define L2CB1_PCIE_PHYMISC2_L0S_TH 3
#define PCIE_PHYMISC2_CDR_BW_MASK 0x3UL
#define PCIE_PHYMISC2_CDR_BW_SHIFT 16
#define L2CB1_PCIE_PHYMISC2_CDR_BW 3
#define REG_TWSI_DEBUG 0x1108
#define TWSI_DEBUG_DEV_EXIST BIT(29)
#define REG_DMA_DBG 0x1114
#define DMA_DBG_VENDOR_MSG BIT(0)
#define REG_EEPROM_CTRL 0x12C0
#define EEPROM_CTRL_DATA_HI_MASK 0xFFFF
#define EEPROM_CTRL_DATA_HI_SHIFT 0
#define EEPROM_CTRL_ADDR_MASK 0x3FF
#define EEPROM_CTRL_ADDR_SHIFT 16
#define EEPROM_CTRL_ACK 0x40000000
#define EEPROM_CTRL_RW 0x80000000
#define REG_EEPROM_DATA_LO 0x12C4
#define REG_OTP_CTRL 0x12F0
#define OTP_CTRL_CLK_EN BIT(1)
#define REG_PM_CTRL 0x12F8
#define PM_CTRL_HOTRST BIT(31)
#define PM_CTRL_MAC_ASPM_CHK BIT(30) /* L0s/L1 dis by MAC based on
* thrghput(setting in 15A0) */
#define PM_CTRL_SA_DLY_EN BIT(29)
#define PM_CTRL_L0S_BUFSRX_EN BIT(28)
#define PM_CTRL_LCKDET_TIMER_MASK 0xFUL
#define PM_CTRL_LCKDET_TIMER_SHIFT 24
#define PM_CTRL_LCKDET_TIMER_DEF 0xC
#define PM_CTRL_PM_REQ_TIMER_MASK 0xFUL
#define PM_CTRL_PM_REQ_TIMER_SHIFT 20 /* pm_request_l1 time > @
* ->L0s not L1 */
#define PM_CTRL_PM_REQ_TO_DEF 0xF
#define PMCTRL_TXL1_AFTER_L0S BIT(19) /* l1dv2.0+ */
#define L1D_PMCTRL_L1_ENTRY_TM_MASK 7UL /* l1dv2.0+, 3bits */
#define L1D_PMCTRL_L1_ENTRY_TM_SHIFT 16
#define L1D_PMCTRL_L1_ENTRY_TM_DIS 0
#define L1D_PMCTRL_L1_ENTRY_TM_2US 1
#define L1D_PMCTRL_L1_ENTRY_TM_4US 2
#define L1D_PMCTRL_L1_ENTRY_TM_8US 3
#define L1D_PMCTRL_L1_ENTRY_TM_16US 4
#define L1D_PMCTRL_L1_ENTRY_TM_24US 5
#define L1D_PMCTRL_L1_ENTRY_TM_32US 6
#define L1D_PMCTRL_L1_ENTRY_TM_63US 7
#define PM_CTRL_L1_ENTRY_TIMER_MASK 0xFUL /* l1C 4bits */
#define PM_CTRL_L1_ENTRY_TIMER_SHIFT 16
#define L2CB1_PM_CTRL_L1_ENTRY_TM 7
#define L1C_PM_CTRL_L1_ENTRY_TM 0xF
#define PM_CTRL_RCVR_WT_TIMER BIT(15) /* 1:1us, 0:2ms */
#define PM_CTRL_CLK_PWM_VER1_1 BIT(14) /* 0:1.0a,1:1.1 */
#define PM_CTRL_CLK_SWH_L1 BIT(13) /* en pcie clk sw in L1 */
#define PM_CTRL_ASPM_L0S_EN BIT(12)
#define PM_CTRL_RXL1_AFTER_L0S BIT(11) /* l1dv2.0+ */
#define L1D_PMCTRL_L0S_TIMER_MASK 7UL /* l1d2.0+, 3bits*/
#define L1D_PMCTRL_L0S_TIMER_SHIFT 8
#define PM_CTRL_L0S_ENTRY_TIMER_MASK 0xFUL /* l1c, 4bits */
#define PM_CTRL_L0S_ENTRY_TIMER_SHIFT 8
#define PM_CTRL_SERDES_BUFS_RX_L1_EN BIT(7)
#define PM_CTRL_SERDES_PD_EX_L1 BIT(6) /* power down serdes rx */
#define PM_CTRL_SERDES_PLL_L1_EN BIT(5)
#define PM_CTRL_SERDES_L1_EN BIT(4)
#define PM_CTRL_ASPM_L1_EN BIT(3)
#define PM_CTRL_CLK_REQ_EN BIT(2)
#define PM_CTRL_RBER_EN BIT(1)
#define PM_CTRL_SPRSDWER_EN BIT(0)
#define REG_LTSSM_ID_CTRL 0x12FC
#define LTSSM_ID_EN_WRO 0x1000
/* Selene Master Control Register */
#define REG_MASTER_CTRL 0x1400
#define MASTER_CTRL_OTP_SEL BIT(31)
#define MASTER_DEV_NUM_MASK 0x7FUL
#define MASTER_DEV_NUM_SHIFT 24
#define MASTER_REV_NUM_MASK 0xFFUL
#define MASTER_REV_NUM_SHIFT 16
#define MASTER_CTRL_INT_RDCLR BIT(14)
#define MASTER_CTRL_CLK_SEL_DIS BIT(12) /* 1:alwys sel pclk from
* serdes, not sw to 25M */
#define MASTER_CTRL_RX_ITIMER_EN BIT(11) /* IRQ MODURATION FOR RX */
#define MASTER_CTRL_TX_ITIMER_EN BIT(10) /* MODURATION FOR TX/RX */
#define MASTER_CTRL_MANU_INT BIT(9) /* SOFT MANUAL INT */
#define MASTER_CTRL_MANUTIMER_EN BIT(8)
#define MASTER_CTRL_SA_TIMER_EN BIT(7) /* SYS ALIVE TIMER EN */
#define MASTER_CTRL_OOB_DIS BIT(6) /* OUT OF BOX DIS */
#define MASTER_CTRL_WAKEN_25M BIT(5) /* WAKE WO. PCIE CLK */
#define MASTER_CTRL_BERT_START BIT(4)
#define MASTER_PCIE_TSTMOD_MASK 3UL
#define MASTER_PCIE_TSTMOD_SHIFT 2
#define MASTER_PCIE_RST BIT(1)
#define MASTER_CTRL_SOFT_RST BIT(0) /* RST MAC & DMA */
#define DMA_MAC_RST_TO 50
/* Timer Initial Value Register */
#define REG_MANUAL_TIMER_INIT 0x1404
/* IRQ ModeratorTimer Initial Value Register */
#define REG_IRQ_MODRT_TIMER_INIT 0x1408
#define IRQ_MODRT_TIMER_MASK 0xffff
#define IRQ_MODRT_TX_TIMER_SHIFT 0
#define IRQ_MODRT_RX_TIMER_SHIFT 16
#define REG_GPHY_CTRL 0x140C
#define GPHY_CTRL_ADDR_MASK 0x1FUL
#define GPHY_CTRL_ADDR_SHIFT 19
#define GPHY_CTRL_BP_VLTGSW BIT(18)
#define GPHY_CTRL_100AB_EN BIT(17)
#define GPHY_CTRL_10AB_EN BIT(16)
#define GPHY_CTRL_PHY_PLL_BYPASS BIT(15)
#define GPHY_CTRL_PWDOWN_HW BIT(14) /* affect MAC&PHY, to low pw */
#define GPHY_CTRL_PHY_PLL_ON BIT(13) /* 1:pll always on, 0:can sw */
#define GPHY_CTRL_SEL_ANA_RST BIT(12)
#define GPHY_CTRL_HIB_PULSE BIT(11)
#define GPHY_CTRL_HIB_EN BIT(10)
#define GPHY_CTRL_GIGA_DIS BIT(9)
#define GPHY_CTRL_PHY_IDDQ_DIS BIT(8) /* pw on RST */
#define GPHY_CTRL_PHY_IDDQ BIT(7) /* bit8 affect bit7 while rb */
#define GPHY_CTRL_LPW_EXIT BIT(6)
#define GPHY_CTRL_GATE_25M_EN BIT(5)
#define GPHY_CTRL_REV_ANEG BIT(4)
#define GPHY_CTRL_ANEG_NOW BIT(3)
#define GPHY_CTRL_LED_MODE BIT(2)
#define GPHY_CTRL_RTL_MODE BIT(1)
#define GPHY_CTRL_EXT_RESET BIT(0) /* 1:out of DSP RST status */
#define GPHY_CTRL_EXT_RST_TO 80 /* 800us atmost */
#define GPHY_CTRL_CLS (\
GPHY_CTRL_LED_MODE |\
GPHY_CTRL_100AB_EN |\
GPHY_CTRL_PHY_PLL_ON)
/* Block IDLE Status Register */
#define REG_IDLE_STATUS 0x1410
#define IDLE_STATUS_SFORCE_MASK 0xFUL
#define IDLE_STATUS_SFORCE_SHIFT 14
#define IDLE_STATUS_CALIB_DONE BIT(13)
#define IDLE_STATUS_CALIB_RES_MASK 0x1FUL
#define IDLE_STATUS_CALIB_RES_SHIFT 8
#define IDLE_STATUS_CALIBERR_MASK 0xFUL
#define IDLE_STATUS_CALIBERR_SHIFT 4
#define IDLE_STATUS_TXQ_BUSY BIT(3)
#define IDLE_STATUS_RXQ_BUSY BIT(2)
#define IDLE_STATUS_TXMAC_BUSY BIT(1)
#define IDLE_STATUS_RXMAC_BUSY BIT(0)
#define IDLE_STATUS_MASK (\
IDLE_STATUS_TXQ_BUSY |\
IDLE_STATUS_RXQ_BUSY |\
IDLE_STATUS_TXMAC_BUSY |\
IDLE_STATUS_RXMAC_BUSY)
/* MDIO Control Register */
#define REG_MDIO_CTRL 0x1414
#define MDIO_CTRL_MODE_EXT BIT(30)
#define MDIO_CTRL_POST_READ BIT(29)
#define MDIO_CTRL_AP_EN BIT(28)
#define MDIO_CTRL_BUSY BIT(27)
#define MDIO_CTRL_CLK_SEL_MASK 0x7UL
#define MDIO_CTRL_CLK_SEL_SHIFT 24
#define MDIO_CTRL_CLK_25_4 0 /* 25MHz divide 4 */
#define MDIO_CTRL_CLK_25_6 2
#define MDIO_CTRL_CLK_25_8 3
#define MDIO_CTRL_CLK_25_10 4
#define MDIO_CTRL_CLK_25_32 5
#define MDIO_CTRL_CLK_25_64 6
#define MDIO_CTRL_CLK_25_128 7
#define MDIO_CTRL_START BIT(23)
#define MDIO_CTRL_SPRES_PRMBL BIT(22)
#define MDIO_CTRL_OP_READ BIT(21) /* 1:read, 0:write */
#define MDIO_CTRL_REG_MASK 0x1FUL
#define MDIO_CTRL_REG_SHIFT 16
#define MDIO_CTRL_DATA_MASK 0xFFFFUL
#define MDIO_CTRL_DATA_SHIFT 0
#define MDIO_MAX_AC_TO 120 /* 1.2ms timeout for slow clk */
/* for extension reg access */
#define REG_MDIO_EXTN 0x1448
#define MDIO_EXTN_PORTAD_MASK 0x1FUL
#define MDIO_EXTN_PORTAD_SHIFT 21
#define MDIO_EXTN_DEVAD_MASK 0x1FUL
#define MDIO_EXTN_DEVAD_SHIFT 16
#define MDIO_EXTN_REG_MASK 0xFFFFUL
#define MDIO_EXTN_REG_SHIFT 0
/* BIST Control and Status Register0 (for the Packet Memory) */
#define REG_BIST0_CTRL 0x141c
#define BIST0_NOW 0x1
#define BIST0_SRAM_FAIL 0x2 /* 1: The SRAM failure is
* un-repairable because
* it has address decoder
* failure or more than 1 cell
* stuck-to-x failure */
#define BIST0_FUSE_FLAG 0x4
/* BIST Control and Status Register1(for the retry buffer of PCI Express) */
#define REG_BIST1_CTRL 0x1420
#define BIST1_NOW 0x1
#define BIST1_SRAM_FAIL 0x2
#define BIST1_FUSE_FLAG 0x4
/* SerDes Lock Detect Control and Status Register */
#define REG_SERDES 0x1424
#define SERDES_PHY_CLK_SLOWDOWN BIT(18)
#define SERDES_MAC_CLK_SLOWDOWN BIT(17)
#define SERDES_SELFB_PLL_MASK 0x3UL
#define SERDES_SELFB_PLL_SHIFT 14
#define SERDES_PHYCLK_SEL_GTX BIT(13) /* 1:gtx_clk, 0:25M */
#define SERDES_PCIECLK_SEL_SRDS BIT(12) /* 1:serdes,0:25M */
#define SERDES_BUFS_RX_EN BIT(11)
#define SERDES_PD_RX BIT(10)
#define SERDES_PLL_EN BIT(9)
#define SERDES_EN BIT(8)
#define SERDES_SELFB_PLL_SEL_CSR BIT(6) /* 0:state-machine,1:csr */
#define SERDES_SELFB_PLL_CSR_MASK 0x3UL
#define SERDES_SELFB_PLL_CSR_SHIFT 4
#define SERDES_SELFB_PLL_CSR_4 3 /* 4-12% OV-CLK */
#define SERDES_SELFB_PLL_CSR_0 2 /* 0-4% OV-CLK */
#define SERDES_SELFB_PLL_CSR_12 1 /* 12-18% OV-CLK */
#define SERDES_SELFB_PLL_CSR_18 0 /* 18-25% OV-CLK */
#define SERDES_VCO_SLOW BIT(3)
#define SERDES_VCO_FAST BIT(2)
#define SERDES_LOCK_DETECT_EN BIT(1)
#define SERDES_LOCK_DETECT BIT(0)
#define REG_LPI_DECISN_TIMER 0x143C
#define L2CB_LPI_DESISN_TIMER 0x7D00
#define REG_LPI_CTRL 0x1440
#define LPI_CTRL_CHK_DA BIT(31)
#define LPI_CTRL_ENH_TO_MASK 0x1FFFUL
#define LPI_CTRL_ENH_TO_SHIFT 12
#define LPI_CTRL_ENH_TH_MASK 0x1FUL
#define LPI_CTRL_ENH_TH_SHIFT 6
#define LPI_CTRL_ENH_EN BIT(5)
#define LPI_CTRL_CHK_RX BIT(4)
#define LPI_CTRL_CHK_STATE BIT(3)
#define LPI_CTRL_GMII BIT(2)
#define LPI_CTRL_TO_PHY BIT(1)
#define LPI_CTRL_EN BIT(0)
#define REG_LPI_WAIT 0x1444
#define LPI_WAIT_TIMER_MASK 0xFFFFUL
#define LPI_WAIT_TIMER_SHIFT 0
/* MAC Control Register */
#define REG_MAC_CTRL 0x1480
#define MAC_CTRL_SPEED_MODE_SW BIT(30) /* 0:phy,1:sw */
#define MAC_CTRL_HASH_ALG_CRC32 BIT(29) /* 1:legacy,0:lw_5b */
#define MAC_CTRL_SINGLE_PAUSE_EN BIT(28)
#define MAC_CTRL_DBG BIT(27)
#define MAC_CTRL_BC_EN BIT(26)
#define MAC_CTRL_MC_ALL_EN BIT(25)
#define MAC_CTRL_RX_CHKSUM_EN BIT(24)
#define MAC_CTRL_TX_HUGE BIT(23)
#define MAC_CTRL_DBG_TX_BKPRESURE BIT(22)
#define MAC_CTRL_SPEED_MASK 3UL
#define MAC_CTRL_SPEED_SHIFT 20
#define MAC_CTRL_SPEED_10_100 1
#define MAC_CTRL_SPEED_1000 2
#define MAC_CTRL_TX_SIMURST BIT(19)
#define MAC_CTRL_SCNT BIT(17)
#define MAC_CTRL_TX_PAUSE BIT(16)
#define MAC_CTRL_PROMIS_EN BIT(15)
#define MAC_CTRL_RMV_VLAN BIT(14)
#define MAC_CTRL_PRMLEN_MASK 0xFUL
#define MAC_CTRL_PRMLEN_SHIFT 10
#define MAC_CTRL_HUGE_EN BIT(9)
#define MAC_CTRL_LENCHK BIT(8)
#define MAC_CTRL_PAD BIT(7)
#define MAC_CTRL_ADD_CRC BIT(6)
#define MAC_CTRL_DUPLX BIT(5)
#define MAC_CTRL_LOOPBACK BIT(4)
#define MAC_CTRL_RX_FLOW BIT(3)
#define MAC_CTRL_TX_FLOW BIT(2)
#define MAC_CTRL_RX_EN BIT(1)
#define MAC_CTRL_TX_EN BIT(0)
/* MAC IPG/IFG Control Register */
#define REG_MAC_IPG_IFG 0x1484
#define MAC_IPG_IFG_IPGT_SHIFT 0 /* Desired back to back
* inter-packet gap. The
* default is 96-bit time */
#define MAC_IPG_IFG_IPGT_MASK 0x7f
#define MAC_IPG_IFG_MIFG_SHIFT 8 /* Minimum number of IFG to
* enforce in between RX frames */
#define MAC_IPG_IFG_MIFG_MASK 0xff /* Frame gap below such IFP is dropped */
#define MAC_IPG_IFG_IPGR1_SHIFT 16 /* 64bit Carrier-Sense window */
#define MAC_IPG_IFG_IPGR1_MASK 0x7f
#define MAC_IPG_IFG_IPGR2_SHIFT 24 /* 96-bit IPG window */
#define MAC_IPG_IFG_IPGR2_MASK 0x7f
/* MAC STATION ADDRESS */
#define REG_MAC_STA_ADDR 0x1488
/* Hash table for multicast address */
#define REG_RX_HASH_TABLE 0x1490
/* MAC Half-Duplex Control Register */
#define REG_MAC_HALF_DUPLX_CTRL 0x1498
#define MAC_HALF_DUPLX_CTRL_LCOL_SHIFT 0 /* Collision Window */
#define MAC_HALF_DUPLX_CTRL_LCOL_MASK 0x3ff
#define MAC_HALF_DUPLX_CTRL_RETRY_SHIFT 12
#define MAC_HALF_DUPLX_CTRL_RETRY_MASK 0xf
#define MAC_HALF_DUPLX_CTRL_EXC_DEF_EN 0x10000
#define MAC_HALF_DUPLX_CTRL_NO_BACK_C 0x20000
#define MAC_HALF_DUPLX_CTRL_NO_BACK_P 0x40000 /* No back-off on backpressure,
* immediately start the
* transmission after back pressure */
#define MAC_HALF_DUPLX_CTRL_ABEBE 0x80000 /* 1: Alternative Binary Exponential Back-off Enabled */
#define MAC_HALF_DUPLX_CTRL_ABEBT_SHIFT 20 /* Maximum binary exponential number */
#define MAC_HALF_DUPLX_CTRL_ABEBT_MASK 0xf
#define MAC_HALF_DUPLX_CTRL_JAMIPG_SHIFT 24 /* IPG to start JAM for collision based flow control in half-duplex */
#define MAC_HALF_DUPLX_CTRL_JAMIPG_MASK 0xf /* mode. In unit of 8-bit time */
/* Maximum Frame Length Control Register */
#define REG_MTU 0x149c
/* Wake-On-Lan control register */
#define REG_WOL_CTRL 0x14a0
#define WOL_PT7_MATCH BIT(31)
#define WOL_PT6_MATCH BIT(30)
#define WOL_PT5_MATCH BIT(29)
#define WOL_PT4_MATCH BIT(28)
#define WOL_PT3_MATCH BIT(27)
#define WOL_PT2_MATCH BIT(26)
#define WOL_PT1_MATCH BIT(25)
#define WOL_PT0_MATCH BIT(24)
#define WOL_PT7_EN BIT(23)
#define WOL_PT6_EN BIT(22)
#define WOL_PT5_EN BIT(21)
#define WOL_PT4_EN BIT(20)
#define WOL_PT3_EN BIT(19)
#define WOL_PT2_EN BIT(18)
#define WOL_PT1_EN BIT(17)
#define WOL_PT0_EN BIT(16)
#define WOL_LNKCHG_ST BIT(10)
#define WOL_MAGIC_ST BIT(9)
#define WOL_PATTERN_ST BIT(8)
#define WOL_OOB_EN BIT(6)
#define WOL_LINK_CHG_PME_EN BIT(5)
#define WOL_LINK_CHG_EN BIT(4)
#define WOL_MAGIC_PME_EN BIT(3)
#define WOL_MAGIC_EN BIT(2)
#define WOL_PATTERN_PME_EN BIT(1)
#define WOL_PATTERN_EN BIT(0)
/* WOL Length ( 2 DWORD ) */
#define REG_WOL_PTLEN1 0x14A4
#define WOL_PTLEN1_3_MASK 0xFFUL
#define WOL_PTLEN1_3_SHIFT 24
#define WOL_PTLEN1_2_MASK 0xFFUL
#define WOL_PTLEN1_2_SHIFT 16
#define WOL_PTLEN1_1_MASK 0xFFUL
#define WOL_PTLEN1_1_SHIFT 8
#define WOL_PTLEN1_0_MASK 0xFFUL
#define WOL_PTLEN1_0_SHIFT 0
#define REG_WOL_PTLEN2 0x14A8
#define WOL_PTLEN2_7_MASK 0xFFUL
#define WOL_PTLEN2_7_SHIFT 24
#define WOL_PTLEN2_6_MASK 0xFFUL
#define WOL_PTLEN2_6_SHIFT 16
#define WOL_PTLEN2_5_MASK 0xFFUL
#define WOL_PTLEN2_5_SHIFT 8
#define WOL_PTLEN2_4_MASK 0xFFUL
#define WOL_PTLEN2_4_SHIFT 0
/* Internal SRAM Partition Register */
#define RFDX_HEAD_ADDR_MASK 0x03FF
#define RFDX_HARD_ADDR_SHIFT 0
#define RFDX_TAIL_ADDR_MASK 0x03FF
#define RFDX_TAIL_ADDR_SHIFT 16
#define REG_SRAM_RFD0_INFO 0x1500
#define REG_SRAM_RFD1_INFO 0x1504
#define REG_SRAM_RFD2_INFO 0x1508
#define REG_SRAM_RFD3_INFO 0x150C
#define REG_RFD_NIC_LEN 0x1510 /* In 8-bytes */
#define RFD_NIC_LEN_MASK 0x03FF
#define REG_SRAM_TRD_ADDR 0x1518
#define TPD_HEAD_ADDR_MASK 0x03FF
#define TPD_HEAD_ADDR_SHIFT 0
#define TPD_TAIL_ADDR_MASK 0x03FF
#define TPD_TAIL_ADDR_SHIFT 16
#define REG_SRAM_TRD_LEN 0x151C /* In 8-bytes */
#define TPD_NIC_LEN_MASK 0x03FF
#define REG_SRAM_RXF_ADDR 0x1520
#define REG_SRAM_RXF_LEN 0x1524
#define REG_SRAM_TXF_ADDR 0x1528
#define REG_SRAM_TXF_LEN 0x152C
#define REG_SRAM_TCPH_ADDR 0x1530
#define REG_SRAM_PKTH_ADDR 0x1532
/*
* Load Ptr Register
* Software sets this bit after the initialization of the head and tail */
#define REG_LOAD_PTR 0x1534
/*
* addresses of all descriptors, as well as the following descriptor
* control register, which triggers each function block to load the head
* pointer to prepare for the operation. This bit is then self-cleared
* after one cycle.
*/
#define REG_RX_BASE_ADDR_HI 0x1540
#define REG_TX_BASE_ADDR_HI 0x1544
#define REG_RFD0_HEAD_ADDR_LO 0x1550
#define REG_RFD1_HEAD_ADDR_LO 0x1554
#define REG_RFD2_HEAD_ADDR_LO 0x1558
#define REG_RFD3_HEAD_ADDR_LO 0x155C
#define REG_RFD_RING_SIZE 0x1560
#define RFD_RING_SIZE_MASK 0x0FFF
#define REG_RX_BUF_SIZE 0x1564
#define RX_BUF_SIZE_MASK 0xFFFF
#define REG_RRD0_HEAD_ADDR_LO 0x1568
#define REG_RRD1_HEAD_ADDR_LO 0x156C
#define REG_RRD2_HEAD_ADDR_LO 0x1570
#define REG_RRD3_HEAD_ADDR_LO 0x1574
#define REG_RRD_RING_SIZE 0x1578
#define RRD_RING_SIZE_MASK 0x0FFF
#define REG_TPD_PRI1_ADDR_LO 0x157C
#define REG_TPD_PRI0_ADDR_LO 0x1580
#define REG_TPD_PRI2_ADDR_LO 0x1F10
#define REG_TPD_PRI3_ADDR_LO 0x1F14
#define REG_TPD_RING_SIZE 0x1584
#define TPD_RING_SIZE_MASK 0xFFFF
/* TXQ Control Register */
#define REG_TXQ_CTRL 0x1590
#define TXQ_TXF_BURST_NUM_MASK 0xFFFFUL
#define TXQ_TXF_BURST_NUM_SHIFT 16
#define L1C_TXQ_TXF_BURST_PREF 0x200
#define L2CB_TXQ_TXF_BURST_PREF 0x40
#define TXQ_CTRL_PEDING_CLR BIT(8)
#define TXQ_CTRL_LS_8023_EN BIT(7)
#define TXQ_CTRL_ENH_MODE BIT(6)
#define TXQ_CTRL_EN BIT(5)
#define TXQ_CTRL_IP_OPTION_EN BIT(4)
#define TXQ_NUM_TPD_BURST_MASK 0xFUL
#define TXQ_NUM_TPD_BURST_SHIFT 0
#define TXQ_NUM_TPD_BURST_DEF 5
#define TXQ_CFGV (\
FIELDX(TXQ_NUM_TPD_BURST, TXQ_NUM_TPD_BURST_DEF) |\
TXQ_CTRL_ENH_MODE |\
TXQ_CTRL_LS_8023_EN |\
TXQ_CTRL_IP_OPTION_EN)
#define L1C_TXQ_CFGV (\
TXQ_CFGV |\
FIELDX(TXQ_TXF_BURST_NUM, L1C_TXQ_TXF_BURST_PREF))
#define L2CB_TXQ_CFGV (\
TXQ_CFGV |\
FIELDX(TXQ_TXF_BURST_NUM, L2CB_TXQ_TXF_BURST_PREF))
/* Jumbo packet Threshold for task offload */
#define REG_TX_TSO_OFFLOAD_THRESH 0x1594 /* In 8-bytes */
#define TX_TSO_OFFLOAD_THRESH_MASK 0x07FF
#define MAX_TSO_FRAME_SIZE (7*1024)
#define REG_TXF_WATER_MARK 0x1598 /* In 8-bytes */
#define TXF_WATER_MARK_MASK 0x0FFF
#define TXF_LOW_WATER_MARK_SHIFT 0
#define TXF_HIGH_WATER_MARK_SHIFT 16
#define TXQ_CTRL_BURST_MODE_EN 0x80000000
#define REG_THRUPUT_MON_CTRL 0x159C
#define THRUPUT_MON_RATE_MASK 0x3
#define THRUPUT_MON_RATE_SHIFT 0
#define THRUPUT_MON_EN 0x80
/* RXQ Control Register */
#define REG_RXQ_CTRL 0x15A0
#define ASPM_THRUPUT_LIMIT_MASK 0x3
#define ASPM_THRUPUT_LIMIT_SHIFT 0
#define ASPM_THRUPUT_LIMIT_NO 0x00
#define ASPM_THRUPUT_LIMIT_1M 0x01
#define ASPM_THRUPUT_LIMIT_10M 0x02
#define ASPM_THRUPUT_LIMIT_100M 0x03
#define IPV6_CHKSUM_CTRL_EN BIT(7)
#define RXQ_RFD_BURST_NUM_MASK 0x003F
#define RXQ_RFD_BURST_NUM_SHIFT 20
#define RXQ_NUM_RFD_PREF_DEF 8
#define RSS_MODE_MASK 3UL
#define RSS_MODE_SHIFT 26
#define RSS_MODE_DIS 0
#define RSS_MODE_SQSI 1
#define RSS_MODE_MQSI 2
#define RSS_MODE_MQMI 3
#define RSS_NIP_QUEUE_SEL BIT(28) /* 0:q0, 1:table */
#define RRS_HASH_CTRL_EN BIT(29)
#define RX_CUT_THRU_EN BIT(30)
#define RXQ_CTRL_EN BIT(31)
#define REG_RFD_FREE_THRESH 0x15A4
#define RFD_FREE_THRESH_MASK 0x003F
#define RFD_FREE_HI_THRESH_SHIFT 0
#define RFD_FREE_LO_THRESH_SHIFT 6
/* RXF flow control register */
#define REG_RXQ_RXF_PAUSE_THRESH 0x15A8
#define RXQ_RXF_PAUSE_TH_HI_SHIFT 0
#define RXQ_RXF_PAUSE_TH_HI_MASK 0x0FFF
#define RXQ_RXF_PAUSE_TH_LO_SHIFT 16
#define RXQ_RXF_PAUSE_TH_LO_MASK 0x0FFF
#define REG_RXD_DMA_CTRL 0x15AC
#define RXD_DMA_THRESH_MASK 0x0FFF /* In 8-bytes */
#define RXD_DMA_THRESH_SHIFT 0
#define RXD_DMA_DOWN_TIMER_MASK 0xFFFF
#define RXD_DMA_DOWN_TIMER_SHIFT 16
/* DMA Engine Control Register */
#define REG_DMA_CTRL 0x15C0
#define DMA_CTRL_SMB_NOW BIT(31)
#define DMA_CTRL_WPEND_CLR BIT(30)
#define DMA_CTRL_RPEND_CLR BIT(29)
#define DMA_CTRL_WDLY_CNT_MASK 0xFUL
#define DMA_CTRL_WDLY_CNT_SHIFT 16
#define DMA_CTRL_WDLY_CNT_DEF 4
#define DMA_CTRL_RDLY_CNT_MASK 0x1FUL
#define DMA_CTRL_RDLY_CNT_SHIFT 11
#define DMA_CTRL_RDLY_CNT_DEF 15
#define DMA_CTRL_RREQ_PRI_DATA BIT(10) /* 0:tpd, 1:data */
#define DMA_CTRL_WREQ_BLEN_MASK 7UL
#define DMA_CTRL_WREQ_BLEN_SHIFT 7
#define DMA_CTRL_RREQ_BLEN_MASK 7UL
#define DMA_CTRL_RREQ_BLEN_SHIFT 4
#define L1C_CTRL_DMA_RCB_LEN128 BIT(3) /* 0:64bytes,1:128bytes */
#define DMA_CTRL_RORDER_MODE_MASK 7UL
#define DMA_CTRL_RORDER_MODE_SHIFT 0
#define DMA_CTRL_RORDER_MODE_OUT 4
#define DMA_CTRL_RORDER_MODE_ENHANCE 2
#define DMA_CTRL_RORDER_MODE_IN 1
/* INT-triggle/SMB Control Register */
#define REG_SMB_STAT_TIMER 0x15C4 /* 2us resolution */
#define SMB_STAT_TIMER_MASK 0xFFFFFF
#define REG_TINT_TPD_THRESH 0x15C8 /* tpd th to trig intrrupt */
/* Mail box */
#define MB_RFDX_PROD_IDX_MASK 0xFFFF
#define REG_MB_RFD0_PROD_IDX 0x15E0
#define REG_MB_RFD1_PROD_IDX 0x15E4
#define REG_MB_RFD2_PROD_IDX 0x15E8
#define REG_MB_RFD3_PROD_IDX 0x15EC
#define REG_TPD_PRI1_PIDX 0x15F0 /* 16bit,hi-tpd producer idx */
#define REG_TPD_PRI0_PIDX 0x15F2 /* 16bit,lo-tpd producer idx */
#define REG_TPD_PRI1_CIDX 0x15F4 /* 16bit,hi-tpd consumer idx */
#define REG_TPD_PRI0_CIDX 0x15F6 /* 16bit,lo-tpd consumer idx */
#define REG_TPD_PRI3_PIDX 0x1F18
#define REG_TPD_PRI2_PIDX 0x1F1A
#define REG_TPD_PRI3_CIDX 0x1F1C
#define REG_TPD_PRI2_CIDX 0x1F1E
#define REG_MB_RFD01_CONS_IDX 0x15F8
#define MB_RFD0_CONS_IDX_MASK 0x0000FFFF
#define MB_RFD1_CONS_IDX_MASK 0xFFFF0000
#define REG_MB_RFD23_CONS_IDX 0x15FC
#define MB_RFD2_CONS_IDX_MASK 0x0000FFFF
#define MB_RFD3_CONS_IDX_MASK 0xFFFF0000
/* Interrupt Status Register */
#define REG_ISR 0x1600
#define ISR_SMB 0x00000001
#define ISR_TIMER 0x00000002
/*
* Software manual interrupt, for debug. Set when SW_MAN_INT_EN is set
* in Table 51 Selene Master Control Register (Offset 0x1400).
*/
#define ISR_MANUAL 0x00000004
#define ISR_HW_RXF_OV 0x00000008 /* RXF overflow interrupt */
#define ISR_RFD0_UR 0x00000010 /* RFD0 under run */
#define ISR_RFD1_UR 0x00000020
#define ISR_RFD2_UR 0x00000040
#define ISR_RFD3_UR 0x00000080
#define ISR_TXF_UR 0x00000100
#define ISR_DMAR_TO_RST 0x00000200
#define ISR_DMAW_TO_RST 0x00000400
#define ISR_TX_CREDIT 0x00000800
#define ISR_GPHY 0x00001000
/* GPHY low power state interrupt */
#define ISR_GPHY_LPW 0x00002000
#define ISR_TXQ_TO_RST 0x00004000
#define ISR_TX_PKT_0 0x00008000
#define ISR_RX_PKT_0 0x00010000
#define ISR_RX_PKT_1 0x00020000
#define ISR_RX_PKT_2 0x00040000
#define ISR_RX_PKT_3 0x00080000
#define ISR_MAC_RX 0x00100000
#define ISR_MAC_TX 0x00200000
#define ISR_UR_DETECTED 0x00400000
#define ISR_FERR_DETECTED 0x00800000
#define ISR_NFERR_DETECTED 0x01000000
#define ISR_CERR_DETECTED 0x02000000
#define ISR_PHY_LINKDOWN 0x04000000
#define ISR_TX_PKT_1 0x10000000
#define ISR_TX_PKT_2 0x20000000
#define ISR_TX_PKT_3 0x40000000
#define ISR_DIS_INT 0x80000000
/* Interrupt Mask Register */
#define REG_IMR 0x1604
#define IMR_NORMAL_MASK (\
ISR_MANUAL |\
ISR_HW_RXF_OV |\
ISR_RFD0_UR |\
ISR_TXF_UR |\
ISR_DMAR_TO_RST |\
ISR_TXQ_TO_RST |\
ISR_DMAW_TO_RST |\
ISR_GPHY |\
ISR_GPHY_LPW |\
ISR_PHY_LINKDOWN)
#define ISR_TX_PKT ( \
ISR_TX_PKT_0 | \
ISR_TX_PKT_1 | \
ISR_TX_PKT_2 | \
ISR_TX_PKT_3)
#define ISR_RX_PKT (\
ISR_RX_PKT_0 |\
ISR_RX_PKT_1 |\
ISR_RX_PKT_2 |\
ISR_RX_PKT_3)
#define ISR_OVER (\
ISR_RFD0_UR |\
ISR_RFD1_UR |\
ISR_RFD2_UR |\
ISR_RFD3_UR |\
ISR_HW_RXF_OV |\
ISR_TXF_UR)
#define ISR_ERROR (\
ISR_DMAR_TO_RST |\
ISR_TXQ_TO_RST |\
ISR_DMAW_TO_RST |\
ISR_PHY_LINKDOWN)
#define REG_INT_RETRIG_TIMER 0x1608
#define INT_RETRIG_TIMER_MASK 0xFFFF
#define REG_MAC_RX_STATUS_BIN 0x1700
#define REG_MAC_RX_STATUS_END 0x175c
#define REG_MAC_TX_STATUS_BIN 0x1760
#define REG_MAC_TX_STATUS_END 0x17c0
#define REG_CLK_GATING_CTRL 0x1814
#define CLK_GATING_DMAW_EN 0x0001
#define CLK_GATING_DMAR_EN 0x0002
#define CLK_GATING_TXQ_EN 0x0004
#define CLK_GATING_RXQ_EN 0x0008
#define CLK_GATING_TXMAC_EN 0x0010
#define CLK_GATING_RXMAC_EN 0x0020
#define CLK_GATING_EN_ALL (CLK_GATING_DMAW_EN |\
CLK_GATING_DMAR_EN |\
CLK_GATING_TXQ_EN |\
CLK_GATING_RXQ_EN |\
CLK_GATING_TXMAC_EN|\
CLK_GATING_RXMAC_EN)
/* DEBUG ADDR */
#define REG_DEBUG_DATA0 0x1900
#define REG_DEBUG_DATA1 0x1904
#define REG_MT_MAGIC 0x1F00
#define REG_MT_MODE 0x1F04
#define REG_MT_SPEED 0x1F08
#define REG_MT_VERSION 0x1F0C
#define MT_MAGIC 0xaabb1234
#define MT_MODE_4Q BIT(0)
#define L1D_MPW_PHYID1 0xD01C /* V7 */
#define L1D_MPW_PHYID2 0xD01D /* V1-V6 */
#define L1D_MPW_PHYID3 0xD01E /* V8 */
/* Autoneg Advertisement Register */
#define ADVERTISE_DEFAULT_CAP \
(ADVERTISE_ALL | ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM)
/* 1000BASE-T Control Register */
#define GIGA_CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port 0=DTE device */
#define GIGA_CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master 0=Configure PHY as Slave */
#define GIGA_CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value 0=Automatic Master/Slave config */
#define GIGA_CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */
#define GIGA_CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */
#define GIGA_CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */
#define GIGA_CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */
#define GIGA_CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */
#define GIGA_CR_1000T_SPEED_MASK 0x0300
#define GIGA_CR_1000T_DEFAULT_CAP 0x0300
/* PHY Specific Status Register */
#define MII_GIGA_PSSR 0x11
#define GIGA_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */
#define GIGA_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */
#define GIGA_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
#define GIGA_PSSR_10MBS 0x0000 /* 00=10Mbs */
#define GIGA_PSSR_100MBS 0x4000 /* 01=100Mbs */
#define GIGA_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
/* PHY Interrupt Enable Register */
#define MII_IER 0x12
#define IER_LINK_UP 0x0400
#define IER_LINK_DOWN 0x0800
/* PHY Interrupt Status Register */
#define MII_ISR 0x13
#define ISR_LINK_UP 0x0400
#define ISR_LINK_DOWN 0x0800
/* Cable-Detect-Test Control Register */
#define MII_CDTC 0x16
#define CDTC_EN_OFF 0 /* sc */
#define CDTC_EN_BITS 1
#define CDTC_PAIR_OFF 8
#define CDTC_PAIR_BIT 2
/* Cable-Detect-Test Status Register */
#define MII_CDTS 0x1C
#define CDTS_STATUS_OFF 8
#define CDTS_STATUS_BITS 2
#define CDTS_STATUS_NORMAL 0
#define CDTS_STATUS_SHORT 1
#define CDTS_STATUS_OPEN 2
#define CDTS_STATUS_INVALID 3
#define MII_DBG_ADDR 0x1D
#define MII_DBG_DATA 0x1E
/***************************** debug port *************************************/
#define MIIDBG_ANACTRL 0x00
#define ANACTRL_CLK125M_DELAY_EN 0x8000
#define ANACTRL_VCO_FAST 0x4000
#define ANACTRL_VCO_SLOW 0x2000
#define ANACTRL_AFE_MODE_EN 0x1000
#define ANACTRL_LCKDET_PHY 0x800
#define ANACTRL_LCKDET_EN 0x400
#define ANACTRL_OEN_125M 0x200
#define ANACTRL_HBIAS_EN 0x100
#define ANACTRL_HB_EN 0x80
#define ANACTRL_SEL_HSP 0x40
#define ANACTRL_CLASSA_EN 0x20
#define ANACTRL_MANUSWON_SWR_MASK 3U
#define ANACTRL_MANUSWON_SWR_SHIFT 2
#define ANACTRL_MANUSWON_SWR_2V 0
#define ANACTRL_MANUSWON_SWR_1P9V 1
#define ANACTRL_MANUSWON_SWR_1P8V 2
#define ANACTRL_MANUSWON_SWR_1P7V 3
#define ANACTRL_MANUSWON_BW3_4M 0x2
#define ANACTRL_RESTART_CAL 0x1
#define ANACTRL_DEF 0x02EF
#define MIIDBG_SYSMODCTRL 0x04
#define SYSMODCTRL_IECHOADJ_PFMH_PHY 0x8000
#define SYSMODCTRL_IECHOADJ_BIASGEN 0x4000
#define SYSMODCTRL_IECHOADJ_PFML_PHY 0x2000
#define SYSMODCTRL_IECHOADJ_PS_MASK 3U
#define SYSMODCTRL_IECHOADJ_PS_SHIFT 10
#define SYSMODCTRL_IECHOADJ_PS_40 3
#define SYSMODCTRL_IECHOADJ_PS_20 2
#define SYSMODCTRL_IECHOADJ_PS_0 1
#define SYSMODCTRL_IECHOADJ_10BT_100MV 0x40 /* 1:100mv, 0:200mv */
#define SYSMODCTRL_IECHOADJ_HLFAP_MASK 3U
#define SYSMODCTRL_IECHOADJ_HLFAP_SHIFT 4
#define SYSMODCTRL_IECHOADJ_VDFULBW 0x8
#define SYSMODCTRL_IECHOADJ_VDBIASHLF 0x4
#define SYSMODCTRL_IECHOADJ_VDAMPHLF 0x2
#define SYSMODCTRL_IECHOADJ_VDLANSW 0x1
#define SYSMODCTRL_IECHOADJ_DEF 0x88BB /* ???? */
/* for l1d & l2cb */
#define SYSMODCTRL_IECHOADJ_CUR_ADD 0x8000
#define SYSMODCTRL_IECHOADJ_CUR_MASK 7U
#define SYSMODCTRL_IECHOADJ_CUR_SHIFT 12
#define SYSMODCTRL_IECHOADJ_VOL_MASK 0xFU
#define SYSMODCTRL_IECHOADJ_VOL_SHIFT 8
#define SYSMODCTRL_IECHOADJ_VOL_17ALL 3
#define SYSMODCTRL_IECHOADJ_VOL_100M15 1
#define SYSMODCTRL_IECHOADJ_VOL_10M17 0
#define SYSMODCTRL_IECHOADJ_BIAS1_MASK 0xFU
#define SYSMODCTRL_IECHOADJ_BIAS1_SHIFT 4
#define SYSMODCTRL_IECHOADJ_BIAS2_MASK 0xFU
#define SYSMODCTRL_IECHOADJ_BIAS2_SHIFT 0
#define L1D_SYSMODCTRL_IECHOADJ_DEF 0x4FBB
#define MIIDBG_SRDSYSMOD 0x05
#define SRDSYSMOD_LCKDET_EN 0x2000
#define SRDSYSMOD_PLL_EN 0x800
#define SRDSYSMOD_SEL_HSP 0x400
#define SRDSYSMOD_HLFTXDR 0x200
#define SRDSYSMOD_TXCLK_DELAY_EN 0x100
#define SRDSYSMOD_TXELECIDLE 0x80
#define SRDSYSMOD_DEEMP_EN 0x40
#define SRDSYSMOD_MS_PAD 0x4
#define SRDSYSMOD_CDR_ADC_VLTG 0x2
#define SRDSYSMOD_CDR_DAC_1MA 0x1
#define SRDSYSMOD_DEF 0x2C46
#define MIIDBG_CFGLPSPD 0x0A
#define CFGLPSPD_RSTCNT_MASK 3U
#define CFGLPSPD_RSTCNT_SHIFT 14
#define CFGLPSPD_RSTCNT_CLK125SW 0x2000
#define MIIDBG_HIBNEG 0x0B
#define HIBNEG_PSHIB_EN 0x8000
#define HIBNEG_WAKE_BOTH 0x4000
#define HIBNEG_ONOFF_ANACHG_SUDEN 0x2000
#define HIBNEG_HIB_PULSE 0x1000
#define HIBNEG_GATE_25M_EN 0x800
#define HIBNEG_RST_80U 0x400
#define HIBNEG_RST_TIMER_MASK 3U
#define HIBNEG_RST_TIMER_SHIFT 8
#define HIBNEG_GTX_CLK_DELAY_MASK 3U
#define HIBNEG_GTX_CLK_DELAY_SHIFT 5
#define HIBNEG_BYPSS_BRKTIMER 0x10
#define HIBNEG_DEF 0xBC40
#define MIIDBG_TST10BTCFG 0x12
#define TST10BTCFG_INTV_TIMER_MASK 3U
#define TST10BTCFG_INTV_TIMER_SHIFT 14
#define TST10BTCFG_TRIGER_TIMER_MASK 3U
#define TST10BTCFG_TRIGER_TIMER_SHIFT 12
#define TST10BTCFG_DIV_MAN_MLT3_EN 0x800
#define TST10BTCFG_OFF_DAC_IDLE 0x400
#define TST10BTCFG_LPBK_DEEP 0x4 /* 1:deep,0:shallow */
#define TST10BTCFG_DEF 0x4C04
#define MIIDBG_AZ_ANADECT 0x15
#define AZ_ANADECT_10BTRX_TH 0x8000
#define AZ_ANADECT_BOTH_01CHNL 0x4000
#define AZ_ANADECT_INTV_MASK 0x3FU
#define AZ_ANADECT_INTV_SHIFT 8
#define AZ_ANADECT_THRESH_MASK 0xFU
#define AZ_ANADECT_THRESH_SHIFT 4
#define AZ_ANADECT_CHNL_MASK 0xFU
#define AZ_ANADECT_CHNL_SHIFT 0
#define AZ_ANADECT_DEF 0x3220
#define AZ_ANADECT_LONG 0xb210
#define MIIDBG_MSE16DB 0x18 /* l1d */
#define L1D_MSE16DB_UP 0x05EA
#define L1D_MSE16DB_DOWN 0x02EA
#define MIIDBG_LEGCYPS 0x29
#define LEGCYPS_EN 0x8000
#define LEGCYPS_DAC_AMP1000_MASK 7U
#define LEGCYPS_DAC_AMP1000_SHIFT 12
#define LEGCYPS_DAC_AMP100_MASK 7U
#define LEGCYPS_DAC_AMP100_SHIFT 9
#define LEGCYPS_DAC_AMP10_MASK 7U
#define LEGCYPS_DAC_AMP10_SHIFT 6
#define LEGCYPS_UNPLUG_TIMER_MASK 7U
#define LEGCYPS_UNPLUG_TIMER_SHIFT 3
#define LEGCYPS_UNPLUG_DECT_EN 0x4
#define LEGCYPS_ECNC_PS_EN 0x1
#define L1D_LEGCYPS_DEF 0x129D
#define L1C_LEGCYPS_DEF 0x36DD
#define MIIDBG_TST100BTCFG 0x36
#define TST100BTCFG_NORMAL_BW_EN 0x8000
#define TST100BTCFG_BADLNK_BYPASS 0x4000
#define TST100BTCFG_SHORTCABL_TH_MASK 0x3FU
#define TST100BTCFG_SHORTCABL_TH_SHIFT 8
#define TST100BTCFG_LITCH_EN 0x80
#define TST100BTCFG_VLT_SW 0x40
#define TST100BTCFG_LONGCABL_TH_MASK 0x3FU
#define TST100BTCFG_LONGCABL_TH_SHIFT 0
#define TST100BTCFG_DEF 0xE12C
#define MIIDBG_VOLT_CTRL 0x3B /* only for l2cb 1 & 2 */
#define VOLT_CTRL_CABLE1TH_MASK 0x1FFU
#define VOLT_CTRL_CABLE1TH_SHIFT 7
#define VOLT_CTRL_AMPCTRL_MASK 3U
#define VOLT_CTRL_AMPCTRL_SHIFT 5
#define VOLT_CTRL_SW_BYPASS 0x10
#define VOLT_CTRL_SWLOWEST 0x8
#define VOLT_CTRL_DACAMP10_MASK 7U
#define VOLT_CTRL_DACAMP10_SHIFT 0
#define MIIDBG_CABLE1TH_DET 0x3E
#define CABLE1TH_DET_EN 0x8000
/******* dev 3 *********/
#define MIIEXT_PCS 3
#define MIIEXT_CLDCTRL3 0x8003
#define CLDCTRL3_BP_CABLE1TH_DET_GT 0x8000
#define CLDCTRL3_AZ_DISAMP 0x1000
#define L2CB_CLDCTRL3 0x4D19
#define L1D_CLDCTRL3 0xDD19
#define MIIEXT_CLDCTRL6 0x8006
#define CLDCTRL6_CAB_LEN_MASK 0x1FFU
#define CLDCTRL6_CAB_LEN_SHIFT 0
#define CLDCTRL6_CAB_LEN_SHORT 0x50
/********* dev 7 **********/
#define MIIEXT_ANEG 7
#define MIIEXT_LOCAL_EEEADV 0x3C
#define LOCAL_EEEADV_1000BT 0x4
#define LOCAL_EEEADV_100BT 0x2
#define MIIEXT_REMOTE_EEEADV 0x3D
#define REMOTE_EEEADV_1000BT 0x4
#define REMOTE_EEEADV_100BT 0x2
#define MIIEXT_EEE_ANEG 0x8000
#define EEE_ANEG_1000M 0x4
#define EEE_ANEG_100M 0x2
#endif /*_ATL1C_HW_H_*/
