What:		/sys/bus/*/drivers/ufshcd/*/auto_hibern8
Date:		March 2018
Contact:	linux-scsi@vger.kernel.org
Description:
		This file contains the auto-hibernate idle timer setting of a
		UFS host controller. A value of '0' means auto-hibernate is not
		enabled. Otherwise the value is the number of microseconds of
		idle time before the UFS host controller will autonomously put
		the link into hibernate state. That will save power at the
		expense of increased latency. Note that the hardware supports
		10-bit values with a power-of-ten multiplier which allows a
		maximum value of 102300000. Refer to the UFS Host Controller
		Interface specification for more details.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/device_type
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the device type. This is one of the UFS
		device descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/device_class
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the device class. This is one of the UFS
		device descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/device_sub_class
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the UFS storage subclass. This is one of
		the UFS device descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/protocol
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the protocol supported by an UFS device.
		This is one of the UFS device descriptor parameters.
		The full information about the descriptor could be found
		at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/number_of_luns
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows number of logical units. This is one of
		the UFS device descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/number_of_wluns
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows number of well known logical units.
		This is one of the UFS device descriptor parameters.
		The full information about the descriptor could be found
		at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/boot_enable
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows value that indicates whether the device is
		enabled for boot. This is one of the UFS device descriptor
		parameters. The full information about the descriptor could
		be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/descriptor_access_enable
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows value that indicates whether the device
		descriptor could be read after partial initialization phase
		of the boot sequence. This is one of the UFS device descriptor
		parameters. The full information about the descriptor could
		be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/initial_power_mode
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows value that defines the power mode after
		device initialization or hardware reset. This is one of
		the UFS device descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/high_priority_lun
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the high priority lun. This is one of
		the UFS device descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/secure_removal_type
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the secure removal type. This is one of
		the UFS device descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/support_security_lun
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows whether the security lun is supported.
		This is one of the UFS device descriptor parameters.
		The full information about the descriptor could be found
		at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/bkops_termination_latency
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the background operations termination
		latency. This is one of the UFS device descriptor parameters.
		The full information about the descriptor could be found
		at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/initial_active_icc_level
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the initial active ICC level. This is one
		of the UFS device descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/specification_version
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the specification version. This is one
		of the UFS device descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/manufacturing_date
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the manufacturing date in BCD format.
		This is one of the UFS device descriptor parameters.
		The full information about the descriptor could be found
		at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/manufacturer_id
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the manufacturee ID. This is one of the
		UFS device descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/rtt_capability
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the maximum number of outstanding RTTs
		supported by the device. This is one of the UFS device
		descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/rtc_update
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the frequency and method of the realtime
		clock update. This is one of the UFS device descriptor
		parameters. The full information about the descriptor
		could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/ufs_features
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows which features are supported by the device.
		This is one of the UFS device descriptor parameters.
		The full information about the descriptor could be
		found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/ffu_timeout
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the FFU timeout. This is one of the
		UFS device descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/queue_depth
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the device queue depth. This is one of the
		UFS device descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/device_version
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the device version. This is one of the
		UFS device descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/number_of_secure_wpa
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows number of secure write protect areas
		supported by the device. This is one of the UFS device
		descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/psa_max_data_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the maximum amount of data that may be
		written during the pre-soldering phase of the PSA flow.
		This is one of the UFS device descriptor parameters.
		The full information about the descriptor could be found
		at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/device_descriptor/psa_state_timeout
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the command maximum timeout for a change
		in PSA state. This is one of the UFS device descriptor
		parameters. The full information about the descriptor could
		be found at UFS specifications 2.1.
		The file is read only.


What:		/sys/bus/platform/drivers/ufshcd/*/interconnect_descriptor/unipro_version
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the MIPI UniPro version number in BCD format.
		This is one of the UFS interconnect descriptor parameters.
		The full information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/interconnect_descriptor/mphy_version
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the MIPI M-PHY version number in BCD format.
		This is one of the UFS interconnect descriptor parameters.
		The full information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.


What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/raw_device_capacity
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the total memory quantity available to
		the user to configure the device logical units. This is one
		of the UFS geometry descriptor parameters. The full
		information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/max_number_of_luns
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the maximum number of logical units
		supported by the UFS device. This is one of the UFS
		geometry descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/segment_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the segment size. This is one of the UFS
		geometry descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/allocation_unit_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the allocation unit size. This is one of
		the UFS geometry descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/min_addressable_block_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the minimum addressable block size. This
		is one of the UFS geometry descriptor parameters. The full
		information about the descriptor could be found at UFS
		specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/optimal_read_block_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the optimal read block size. This is one
		of the UFS geometry descriptor parameters. The full
		information about the descriptor could be found at UFS
		specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/optimal_write_block_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the optimal write block size. This is one
		of the UFS geometry descriptor parameters. The full
		information about the descriptor could be found at UFS
		specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/max_in_buffer_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the maximum data-in buffer size. This
		is one of the UFS geometry descriptor parameters. The full
		information about the descriptor could be found at UFS
		specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/max_out_buffer_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the maximum data-out buffer size. This
		is one of the UFS geometry descriptor parameters. The full
		information about the descriptor could be found at UFS
		specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/rpmb_rw_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the maximum number of RPMB frames allowed
		in Security Protocol In/Out. This is one of the UFS geometry
		descriptor parameters. The full information about the
		descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/dyn_capacity_resource_policy
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the dynamic capacity resource policy. This
		is one of the UFS geometry descriptor parameters. The full
		information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/data_ordering
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows support for out-of-order data transfer.
		This is one of the UFS geometry descriptor parameters.
		The full information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/max_number_of_contexts
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows maximum available number of contexts which
		are supported by the device. This is one of the UFS geometry
		descriptor parameters. The full information about the
		descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/sys_data_tag_unit_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows system data tag unit size. This is one of
		the UFS geometry descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/sys_data_tag_resource_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows maximum storage area size allocated by
		the device to handle system data by the tagging mechanism.
		This is one of the UFS geometry descriptor parameters.
		The full information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/secure_removal_types
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows supported secure removal types. This is
		one of the UFS geometry descriptor parameters. The full
		information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/memory_types
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows supported memory types. This is one of
		the UFS geometry descriptor parameters. The full
		information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/*_memory_max_alloc_units
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the maximum number of allocation units for
		different memory types (system code, non persistent,
		enhanced type 1-4). This is one of the UFS geometry
		descriptor parameters. The full information about the
		descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/*_memory_capacity_adjustment_factor
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the memory capacity adjustment factor for
		different memory types (system code, non persistent,
		enhanced type 1-4). This is one of the UFS geometry
		descriptor parameters. The full information about the
		descriptor could be found at UFS specifications 2.1.
		The file is read only.


What:		/sys/bus/platform/drivers/ufshcd/*/health_descriptor/eol_info
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows preend of life information. This is one
		of the UFS health descriptor parameters. The full
		information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/health_descriptor/life_time_estimation_a
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows indication of the device life time
		(method a). This is one of the UFS health descriptor
		parameters. The full information about the descriptor
		could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/health_descriptor/life_time_estimation_b
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows indication of the device life time
		(method b). This is one of the UFS health descriptor
		parameters. The full information about the descriptor
		could be found at UFS specifications 2.1.
		The file is read only.


What:		/sys/bus/platform/drivers/ufshcd/*/power_descriptor/active_icc_levels_vcc*
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows maximum VCC, VCCQ and VCCQ2 value for
		active ICC levels from 0 to 15. This is one of the UFS
		power descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.


What:		/sys/bus/platform/drivers/ufshcd/*/string_descriptors/manufacturer_name
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file contains a device manufactureer name string.
		The full information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/string_descriptors/product_name
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file contains a product name string. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/string_descriptors/oem_id
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file contains a OEM ID string. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/string_descriptors/serial_number
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file contains a device serial number string. The full
		information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/string_descriptors/product_revision
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file contains a product revision string. The full
		information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.


What:		/sys/class/scsi_device/*/device/unit_descriptor/boot_lun_id
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows boot LUN information. This is one of
		the UFS unit descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/class/scsi_device/*/device/unit_descriptor/lun_write_protect
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows LUN write protection status. This is one of
		the UFS unit descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/class/scsi_device/*/device/unit_descriptor/lun_queue_depth
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows LUN queue depth. This is one of the UFS
		unit descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/class/scsi_device/*/device/unit_descriptor/psa_sensitive
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows PSA sensitivity. This is one of the UFS
		unit descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/class/scsi_device/*/device/unit_descriptor/lun_memory_type
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows LUN memory type. This is one of the UFS
		unit descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/class/scsi_device/*/device/unit_descriptor/data_reliability
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file defines the device behavior when a power failure
		occurs during a write operation. This is one of the UFS
		unit descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/class/scsi_device/*/device/unit_descriptor/logical_block_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the size of addressable logical blocks
		(calculated as an exponent with base 2). This is one of
		the UFS unit descriptor parameters. The full information about
		the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/class/scsi_device/*/device/unit_descriptor/logical_block_count
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows total number of addressable logical blocks.
		This is one of the UFS unit descriptor parameters. The full
		information about the descriptor could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/class/scsi_device/*/device/unit_descriptor/erase_block_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the erase block size. This is one of
		the UFS unit descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/class/scsi_device/*/device/unit_descriptor/provisioning_type
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the thin provisioning type. This is one of
		the UFS unit descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/class/scsi_device/*/device/unit_descriptor/physical_memory_resourse_count
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the total physical memory resources. This is
		one of the UFS unit descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/class/scsi_device/*/device/unit_descriptor/context_capabilities
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the context capabilities. This is one of
		the UFS unit descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/class/scsi_device/*/device/unit_descriptor/large_unit_granularity
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the granularity of the LUN. This is one of
		the UFS unit descriptor parameters. The full information
		about the descriptor could be found at UFS specifications 2.1.
		The file is read only.


What:		/sys/bus/platform/drivers/ufshcd/*/flags/device_init
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the device init status. The full information
		about the flag could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/flags/permanent_wpe
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows whether permanent write protection is enabled.
		The full information about the flag could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/flags/power_on_wpe
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows whether write protection is enabled on all
		logical units configured as power on write protected. The
		full information about the flag could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/flags/bkops_enable
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows whether the device background operations are
		enabled. The full information about the flag could be
		found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/flags/life_span_mode_enable
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows whether the device life span mode is enabled.
		The full information about the flag could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/flags/phy_resource_removal
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows whether physical resource removal is enable.
		The full information about the flag could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/flags/busy_rtc
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows whether the device is executing internal
		operation related to real time clock. The full information
		about the flag could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/flags/disable_fw_update
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows whether the device FW update is permanently
		disabled. The full information about the flag could be found
		at UFS specifications 2.1.
		The file is read only.


What:		/sys/bus/platform/drivers/ufshcd/*/attributes/boot_lun_enabled
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file provides the boot lun enabled UFS device attribute.
		The full information about the attribute could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/current_power_mode
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file provides the current power mode UFS device attribute.
		The full information about the attribute could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/active_icc_level
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file provides the active icc level UFS device attribute.
		The full information about the attribute could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/ooo_data_enabled
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file provides the out of order data transfer enabled UFS
		device attribute. The full information about the attribute
		could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/bkops_status
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file provides the background operations status UFS device
		attribute. The full information about the attribute could
		be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/purge_status
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file provides the purge operation status UFS device
		attribute. The full information about the attribute could
		be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/max_data_in_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the maximum data size in a DATA IN
		UPIU. The full information about the attribute could
		be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/max_data_out_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the maximum number of bytes that can be
		requested with a READY TO TRANSFER UPIU. The full information
		about the attribute could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/reference_clock_frequency
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file provides the reference clock frequency UFS device
		attribute. The full information about the attribute could
		be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/configuration_descriptor_lock
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows whether the configuration descriptor is locked.
		The full information about the attribute could be found at
		UFS specifications 2.1. The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/max_number_of_rtt
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file provides the maximum current number of
		outstanding RTTs in device that is allowed. The full
		information about the attribute could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/exception_event_control
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file provides the exception event control UFS device
		attribute. The full information about the attribute could
		be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/exception_event_status
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file provides the exception event status UFS device
		attribute. The full information about the attribute could
		be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/ffu_status
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file provides the ffu status UFS device attribute.
		The full information about the attribute could be found at
		UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/psa_state
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file show the PSA feature status. The full information
		about the attribute could be found at UFS specifications 2.1.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/attributes/psa_data_size
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the amount of data that the host plans to
		load to all logical units in pre-soldering state.
		The full information about the attribute could be found at
		UFS specifications 2.1.
		The file is read only.


What:		/sys/class/scsi_device/*/device/dyn_cap_needed
Date:		February 2018
Contact:	Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Description:	This file shows the The amount of physical memory needed
		to be removed from the physical memory resources pool of
		the particular logical unit. The full information about
		the attribute could be found at UFS specifications 2.1.
		The file is read only.


What:		/sys/bus/platform/drivers/ufshcd/*/rpm_lvl
Date:		September 2014
Contact:	Subhash Jadavani <subhashj@codeaurora.org>
Description:	This entry could be used to set or show the UFS device
		runtime power management level. The current driver
		implementation supports 6 levels with next target states:
		0 - an UFS device will stay active, an UIC link will
		stay active
		1 - an UFS device will stay active, an UIC link will
		hibernate
		2 - an UFS device will moved to sleep, an UIC link will
		stay active
		3 - an UFS device will moved to sleep, an UIC link will
		hibernate
		4 - an UFS device will be powered off, an UIC link will
		hibernate
		5 - an UFS device will be powered off, an UIC link will
		be powered off

What:		/sys/bus/platform/drivers/ufshcd/*/rpm_target_dev_state
Date:		February 2018
Contact:	Subhash Jadavani <subhashj@codeaurora.org>
Description:	This entry shows the target power mode of an UFS device
		for the chosen runtime power management level.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/rpm_target_link_state
Date:		February 2018
Contact:	Subhash Jadavani <subhashj@codeaurora.org>
Description:	This entry shows the target state of an UFS UIC link
		for the chosen runtime power management level.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/spm_lvl
Date:		September 2014
Contact:	Subhash Jadavani <subhashj@codeaurora.org>
Description:	This entry could be used to set or show the UFS device
		system power management level. The current driver
		implementation supports 6 levels with next target states:
		0 - an UFS device will stay active, an UIC link will
		stay active
		1 - an UFS device will stay active, an UIC link will
		hibernate
		2 - an UFS device will moved to sleep, an UIC link will
		stay active
		3 - an UFS device will moved to sleep, an UIC link will
		hibernate
		4 - an UFS device will be powered off, an UIC link will
		hibernate
		5 - an UFS device will be powered off, an UIC link will
		be powered off

What:		/sys/bus/platform/drivers/ufshcd/*/spm_target_dev_state
Date:		February 2018
Contact:	Subhash Jadavani <subhashj@codeaurora.org>
Description:	This entry shows the target power mode of an UFS device
		for the chosen system power management level.
		The file is read only.

What:		/sys/bus/platform/drivers/ufshcd/*/spm_target_link_state
Date:		February 2018
Contact:	Subhash Jadavani <subhashj@codeaurora.org>
Description:	This entry shows the target state of an UFS UIC link
		for the chosen system power management level.
		The file is read only.