// SPDX-License-Identifier: GPL-2.0-only
/*
 * Devicetree for the Samsung Galaxy Beam GT-I8530 also known as Gavini.
 */

/dts-v1/;
#include "ste-db8500.dtsi"
#include "ste-ab8500.dtsi"
#include "ste-dbx5x0-pinctrl.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>

/ {
	model = "Samsung Galaxy Beam (GT-I8530)";
	compatible = "samsung,gavini", "st-ericsson,u8500";

	chosen {
		stdout-path = &serial2;
	};

	/* TI TXS0206 level translator for 2.9 V */
	sd_level_translator: regulator-gpio {
		compatible = "regulator-fixed";

		/* GPIO193 EN */
		gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>;
		enable-active-high;

		regulator-name = "sd-level-translator";
		regulator-min-microvolt = <2900000>;
		regulator-max-microvolt = <2900000>;
		regulator-type = "voltage";

		startup-delay-us = <200>;

		pinctrl-names = "default";
		pinctrl-0 = <&sd_level_translator_default>;
	};

	/* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */
	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
		compatible = "regulator-fixed";
		/* Supplied in turn by VBAT */
		regulator-name = "VMEM_3V3";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
		startup-delay-us = <5000>; // FIXME
		enable-active-high;
		pinctrl-names = "default";
		pinctrl-0 = <&emmc_ldo_en_default_mode>;
	};

	/*
	 * External Ricoh "TSP" regulator for the touchscreen.
	 * One GPIO line controls two voltages of 3.3V and 1.8V
	 * this line is known as "TSP_LDO_ON1" in the schematics.
	 */
	ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 {
		compatible = "regulator-fixed";
		/* Supplied in turn by VBAT */
		regulator-name = "LDO_TSP_A3V3";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		/* GPIO94 controls this regulator */
		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
		/* 70 ms power-on delay */
		startup-delay-us = <70000>;
		enable-active-high;
		pinctrl-names = "default";
		pinctrl-0 = <&tsp_ldo_en_default_mode>;
	};
	ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 {
		compatible = "regulator-fixed";
		/* Supplied in turn by VBAT */
		regulator-name = "VREG_TSP_1V8";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		/* GPIO94 controls this regulator */
		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
		/* 70 ms power-on delay */
		startup-delay-us = <70000>;
		enable-active-high;
		pinctrl-names = "default";
		pinctrl-0 = <&tsp_ldo_en_default_mode>;
	};

	/*
	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
	 * LCD_PWR_EN controls both a 3.0V and 1.8V output.
	 */
	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
		compatible = "regulator-fixed";
		/* Supplied in turn by VBAT */
		regulator-name = "VREG_LCD_3V0";
		regulator-min-microvolt = <3000000>;
		regulator-max-microvolt = <3000000>;
		/* GPIO219 controls this regulator */
		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
		enable-active-high;
		pinctrl-names = "default";
		pinctrl-0 = <&lcd_pwr_en_default_mode>;
	};
	lcd_1v8_reg: regulator-gpio-lcd-1v8 {
		compatible = "regulator-fixed";
		/* Supplied in turn by VBAT */
		regulator-name = "VREG_LCD_1V8";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		/* GPIO219 controls this regulator too */
		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
		enable-active-high;
		pinctrl-names = "default";
		pinctrl-0 = <&lcd_pwr_en_default_mode>;
	};

	/*
	 * This regulator is a GPIO line that drives the Broadcom WLAN
	 * line WL_REG_ON high and enables the internal regulators
	 * inside the chip. Unfortunatley it is erroneously named
	 * WLAN_RST_N on the schematic but it is not a reset line.
	 *
	 * The voltage specified here is only used to determine the OCR mask,
	 * the for the SDIO connector, the chip is actually connected
	 * directly to VBAT.
	 */
	wl_reg: regulator-gpio-wlan {
		compatible = "regulator-fixed";
		regulator-name = "WL_REG_ON";
		regulator-min-microvolt = <3000000>;
		regulator-max-microvolt = <3000000>;
		startup-delay-us = <100000>;
		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
		enable-active-high;
		pinctrl-names = "default";
		pinctrl-0 = <&wlan_ldo_en_default>;
	};

	gpio-keys {
		compatible = "gpio-keys";
		pinctrl-names = "default";
		pinctrl-0 = <&gpio_keys_default_mode>;

		button-projector {
			linux,code = <KEY_SWITCHVIDEOMODE>;
			label = "Projector";
			/* GPIO32 "Projector On HotKey" */
			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
		};
		button-home {
			linux,code = <KEY_HOME>;
			label = "HOME";
			/* GPIO91 */
			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
		};
		button-volup {
			linux,code = <KEY_VOLUMEUP>;
			label = "VOL+";
			/* GPIO67 */
			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
		};
		button-voldown {
			linux,code = <KEY_VOLUMEDOWN>;
			label = "VOL-";
			/* GPIO92 */
			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
		};
	};

	/* Richtek RT8515GQW Flash LED Driver IC */
	flash {
		compatible = "richtek,rt8515";
		/* GPIO 140 */
		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
		/* GPIO 141 */
		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
		/*
		 * RFS is 16 kOhm and RTS is 100 kOhm giving
		 * the flash max current 343mA and torch max
		 * current 55 mA.
		 */
		richtek,rfs-ohms = <16000>;
		richtek,rts-ohms = <100000>;
		pinctrl-names = "default";
		pinctrl-0 = <&gpio_flash_default_mode>;

		led {
			function = LED_FUNCTION_FLASH;
			color = <LED_COLOR_ID_WHITE>;
			flash-max-timeout-us = <250000>;
			flash-max-microamp = <343750>;
			led-max-microamp = <55000>;
		};
	};

	gpio-leds {
		compatible = "gpio-leds";
		pinctrl-names = "default";
		pinctrl-0 = <&gpio_leds_default_mode>;
		used-led {
			label = "touchkeys";
			/* GPIO68 */
			gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
			default-state = "on";
		};
	};

	ktd259: backlight {
		compatible = "kinetic,ktd259";
		/* GPIO20 */
		enable-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
		/* Default to 13/32 brightness */
		default-brightness = <13>;
		pinctrl-names = "default";
		pinctrl-0 = <&ktd259_backlight_default_mode>;
	};

	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
	i2c-gpio-0 {
		compatible = "i2c-gpio";
		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
		pinctrl-names = "default";
		pinctrl-0 = <&i2c_gpio_0_default>;
		#address-cells = <1>;
		#size-cells = <0>;

		/* TODO: Memsic MMC328 magnetometer */
		magnetometer@30 {
			compatible = "memsic,mmc328";
			reg = <0x30>;
			/* TODO: if you have the schematic, check if both voltages come from AUX2 */
			/* VDA 1.8 V */
			vda-supply = <&ab8500_ldo_aux2_reg>;
			/* VDD 1.8V */
			vdd-supply = <&ab8500_ldo_aux2_reg>;
			/* GPIO204 */
			reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
			pinctrl-names = "default";
			pinctrl-0 = <&mmc328_default>;
		};
		/* TODO: this should also be used by the NCP6914 Camera power management unit */
	};

	/*
	 * TODO: See if we can use the PL023 for this instead.
	 */
	spi-gpio-0 {
		compatible = "spi-gpio";
		/* Clock on GPIO220, pin SCL */
		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
		/* MOSI on GPIO224, pin SDI "slave data in" */
		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
		/* MISO on GPIO225, pin SDO "slave data out" */
		miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
		/* Chip select on GPIO223 */
		cs-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
		num-chipselects = <1>;

		pinctrl-names = "default";
		pinctrl-0 = <&spi_gpio_0_default>;
		#address-cells = <1>;
		#size-cells = <0>;

		panel@0 {
			compatible = "samsung,lms397kf04";
			/* 300 ns at read cycle -> 3 MHz max speed */
			//spi-max-frequency = <3000000>;
			spi-max-frequency = <1200000>;
			/* TYPE 3: inverse clock polarity and phase */
			spi-cpha;
			spi-cpol;

			reg = <0>;
			vci-supply = <&lcd_3v0_reg>;
			vccio-supply = <&lcd_1v8_reg>;
			/* Reset on GPIO139 */
			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
			pinctrl-names = "default";
			pinctrl-0 = <&panel_default_mode>;
			backlight = <&ktd259>;

			port {
				panel_in: endpoint {
					remote-endpoint = <&display_out>;
				};
			};
		};
	};

	/* Bit-banged I2C on GPIO201 and GPIO202 also called "MOT_I2C" */
	i2c-gpio-2 {
		compatible = "i2c-gpio";
		sda-gpios = <&gpio6 10 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
		scl-gpios = <&gpio6 9 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
		pinctrl-names = "default";
		pinctrl-0 = <&i2c_gpio_2_default>;
		#address-cells = <1>;
		#size-cells = <0>;
		/* TODO: add the Immersion ISA1200 I2C device here */
	};

	/* Bit-banged I2C on GPIO196 and GPIO197 also called "MPR_I2C" */
	i2c-gpio-3 {
		compatible = "i2c-gpio";
		sda-gpios = <&gpio6 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
		scl-gpios = <&gpio6 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
		pinctrl-names = "default";
		pinctrl-0 = <&i2c_gpio_3_default>;
		#address-cells = <1>;
		#size-cells = <0>;
		/* TODO: add the DPP2601 projector I2C device 0x1b here */
	};

	soc {
		/* External Micro SD slot */
		mmc@80126000 {
			arm,primecell-periphid = <0x10480180>;
			max-frequency = <50000000>;
			bus-width = <4>;
			cap-sd-highspeed;
			cap-mmc-highspeed;
			st,sig-pin-fbclk;
			full-pwr-cycle;
			/* MMC is powered by AUX3 1.2V .. 2.91V */
			vmmc-supply = <&ab8500_ldo_aux3_reg>;
			/* 2.9 V level translator */
			vqmmc-supply = <&sd_level_translator>;
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&mc0_a_2_default>;
			pinctrl-1 = <&mc0_a_2_sleep>;
			/* "flash detect" actually card detect */
			cd-gpios  = <&gpio6 25 GPIO_ACTIVE_LOW>;
			status = "okay";
		};

		/* WLAN SDIO channel */
		mmc@80118000 {
			arm,primecell-periphid = <0x10480180>;
			max-frequency = <50000000>;
			bus-width = <4>;
			non-removable;
			cap-sd-highspeed;
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&mc1_a_2_default>;
			pinctrl-1 = <&mc1_a_2_sleep>;
			/*
			 * GPIO-controlled voltage enablement: this drives
			 * the WL_REG_ON line high when we use this device.
			 * Represented as regulator to fill OCR mask.
			 */
			vmmc-supply = <&wl_reg>;

			#address-cells = <1>;
			#size-cells = <0>;
			status = "okay";

			wifi@1 {
				compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
				reg = <1>;
				/* GPIO216 WL_HOST_WAKE */
				interrupt-parent = <&gpio6>;
				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
				interrupt-names = "host-wake";
				pinctrl-names = "default";
				pinctrl-0 = <&wlan_default_mode>;
			};
		};

		/* eMMC */
		mmc@80005000 {
			arm,primecell-periphid = <0x10480180>;
		        max-frequency = <50000000>;
			bus-width = <8>;
			non-removable;
			cap-mmc-highspeed;
			mmc-ddr-1_8v;
			no-sdio;
			no-sd;
			vmmc-supply = <&ldo_3v3_reg>;
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&mc2_a_1_default>;
			pinctrl-1 = <&mc2_a_1_sleep>;
			status = "okay";
		};

		/* GBF (Bluetooth) UART */
		uart@80120000 {
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&u0_a_1_default>;
			pinctrl-1 = <&u0_a_1_sleep>;
			status = "okay";

			bluetooth {
				compatible = "brcm,bcm4330-bt";
				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
				/* BT_WAKE on GPIO199 */
				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
				/* BT_HOST_WAKE on GPIO97 */
				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
				/* BT_RST_N on GPIO209 */
				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
				pinctrl-names = "default";
				pinctrl-0 = <&bluetooth_default_mode>;
			};
		};

		/* GPS UART */
		uart@80121000 {
			status = "okay";
			pinctrl-names = "default", "sleep";
			/* CTS/RTS is not used, CTS is repurposed as GPIO */
			pinctrl-0 = <&u1rxtx_a_1_default>;
			pinctrl-1 = <&u1rxtx_a_1_sleep>;
			/* FIXME: add a device for the GPS here */
		};

		/* Debugging console UART connected to TSU6111RSVR (FSA880) */
		uart@80007000 {
			status = "okay";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&u2rxtx_c_1_default>;
			pinctrl-1 = <&u2rxtx_c_1_sleep>;
		};

		prcmu@80157000 {
			ab8500 {
				ab8500_usb {
					pinctrl-names = "default", "sleep";
					pinctrl-0 = <&usb_a_1_default>;
					pinctrl-1 = <&usb_a_1_sleep>;
				};

				ab8500-regulators {
					ab8500_ldo_aux1 {
						/* Used for VDD for sensors */
						regulator-name = "V-SENSORS-VDD";
						regulator-min-microvolt = <3000000>;
						regulator-max-microvolt = <3000000>;
					};

					ab8500_ldo_aux2 {
						/* Used for VIO for sensors */
						regulator-name = "V-SENSORS-VIO";
						regulator-min-microvolt = <1800000>;
						regulator-max-microvolt = <1800000>;
					};

					ab8500_ldo_aux3 {
						/* Used for voltage for external MMC/SD card */
						regulator-name = "V-MMC-SD";
						regulator-min-microvolt = <1200000>;
						regulator-max-microvolt = <2910000>;
					};
				};
			};
		};

		/* I2C0 */
		i2c@80004000 {
			status = "okay";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&i2c0_a_1_default>;
			pinctrl-1 = <&i2c0_a_1_sleep>;

			/* FIXME: fix the proximity sensor bindings and driver */
			proximity@39 {
				/* Gavini has the GP2A030S00F proximity sensor */
				compatible = "sharp,gp2a030s00f";
				clock-frequency = <400000>;
				reg = <0x39>;
				/* FIXME: GPIO146 provides power on, IR LED? */
			};

			gyroscope@68 {
				compatible = "invensense,mpu3050";
				reg = <0x68>;
				/* GPIO226 interrupt */
				interrupt-parent = <&gpio7>;
				interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
				mount-matrix = "0", "1", "0",
					       "1", "0", "0",
					       "0", "0", "1";
				vlogic-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
				pinctrl-names = "default";
				pinctrl-0 = <&mpu3050_default>;

				/*
				 * The MPU-3050 acts as a hub for the
				 * accelerometer.
				 */
				i2c-gate {
					#address-cells = <1>;
					#size-cells = <0>;

					/* Bosch BMA222E accelerometer */
					accelerometer@18 {
						compatible = "bosch,bma222e";
						reg = <0x18>;
						mount-matrix = "0", "1", "0",
							       "-1", "0", "0",
							       "0", "0", "1";
						vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
						vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
					};
				};
			};
		};

		/* I2C2 "AGC I2C" */
		i2c@80128000 {
			status = "okay";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&i2c2_b_1_default>;
			pinctrl-1 = <&i2c2_b_1_sleep>;

			/* Texas Instruments TSU6111 micro USB switch */
			usb-switch@25 {
				compatible = "ti,tsu6111";
				reg = <0x25>;
				/* Interrupt JACK_INT_N on GPIO95 */
				interrupt-parent = <&gpio2>;
				interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
				pinctrl-names = "default";
				pinctrl-0 = <&tsu6111_default>;
			};
		};

		/* I2C3 */
		i2c@80110000 {
			status = "okay";

			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&i2c3_c_2_default>;
			pinctrl-1 = <&i2c3_c_2_sleep>;

			/* Melfas MMS136 touchscreen */
			touchscreen@48 {
				compatible = "melfas,mms136";
				reg = <0x48>;
				/* GPIO218 (TSP_INT_1V8) */
				interrupt-parent = <&gpio6>;
				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
				/* AVDD is "analog supply", 2.57-3.47 V */
				avdd-supply = <&ldo_tsp_3v3_reg>;
				/* VDD is "digital supply" 1.71-3.47V */
				vdd-supply = <&ldo_tsp_1v8_reg>;
				pinctrl-names = "default";
				pinctrl-0 = <&tsp_default>;
				touchscreen-size-x = <480>;
				touchscreen-size-y = <800>;
			};
		};

		mcde@a0350000 {
			status = "okay";
			pinctrl-names = "default";
			pinctrl-0 = <&dpi_default_mode>;

			port {
				display_out: endpoint {
					remote-endpoint = <&panel_in>;
				};
			};
		};
	};
};

&pinctrl {
	/*
	 * This extends the MC0_A_2 default config to include
	 * the card detect GPIO217 line.
	 */
	sdi0 {
		mc0_a_2_default {
			default_cfg4 {
				pins = "GPIO217_AH12"; /* card detect */
				ste,config = <&gpio_in_nopull>;
			};
		};
	};
	mcde {
		dpi_default_mode: dpi_default {
			default_mux1 {
				/* Mux in all the data lines */
				function = "lcd";
				groups =
					/* Data lines D0-D7 GPIO70..GPIO77 */
					"lcd_d0_d7_a_1",
					/* Data lines D8-D11 GPIO78..GPIO81 */
					"lcd_d8_d11_a_1",
					/* Data lines D12-D15 GPIO82..GPIO85 */
					"lcd_d12_d15_a_1",
					/* Data lines D16-D23 GPIO161..GPIO168 */
					"lcd_d16_d23_b_1";
			};
			default_mux2 {
				function = "lcda";
				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
				groups = "lcdaclk_b_1", "lcda_b_1";
			};
			/* Input, no pull-up is the default state for pins used for an alt function */
			default_cfg1 {
				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
				ste,config = <&in_nopull>;
			};
		};
	};
	/* GPIO for panel reset control */
	panel {
		panel_default_mode: panel_default {
			gavini_cfg1 {
				/* Reset line */
				pins = "GPIO139_C9";
				ste,config = <&gpio_out_lo>;
			};
		};
	};
	/* GPIO that enables the LDO regulator for the eMMC */
	emmc-ldo {
		emmc_ldo_en_default_mode: emmc_ldo_default {
			/* LDO enable on GPIO6 */
			gavini_cfg1 {
				pins = "GPIO6_AF6";
				ste,config = <&gpio_out_hi>;
			};
		};
	};
	/* GPIO that enables the LDO regulator for the touchscreen */
	tsp-ldo {
		tsp_ldo_en_default_mode: tsp_ldo_default {
			/* LDO enable on GPIO94 */
			gavini_cfg1 {
				pins = "GPIO94_D7";
				ste,config = <&gpio_out_hi>;
			};
		};
	};
	/* Flash and torch */
	flash {
		gpio_flash_default_mode: flash_default {
			janice_cfg1 {
				pins = "GPIO140_B11", "GPIO141_C12";
				ste,config = <&gpio_out_lo>;
			};
		};
	};
	/* GPIO that enables the LDO regulator for the key LED */
	gpio-leds {
		gpio_leds_default_mode: gpio_leds_default {
			/* EN_LED_LDO on GPIO68 */
			gavini_cfg1 {
				pins = "GPIO68_E1";
				ste,config = <&gpio_out_hi>;
			};
		};
	};
	backlight {
		ktd259_backlight_default_mode: backlight_default {
			skomer_cfg1 {
				pins = "GPIO20_AB4"; /* LCD_BL_EN */
				ste,config = <&gpio_out_lo>;
			};
		};
	};
	/* GPIO that enables the LDO regulator for the touchkeys */
	touchkey-ldo {
		tsp_ldo_on2_default_mode: tsp_ldo_on2_default {
			/* TSP_LDO_ON2 on GPIO89 */
			gavini_cfg1 {
				pins = "GPIO89_E6";
				ste,config = <&gpio_out_lo>;
			};
		};
	};
	touchkey {
		touchkey_default_mode: touchkey_default {
			gavini_cfg1 {
				/* Interrupt */
				pins = "GPIO198_AG25";
				ste,config = <&gpio_in_nopull>;
			};
			gavini_cfg2 {
				/* Reset, actually completely unused (not routed) */
				pins = "GPIO205_AG23";
				ste,config = <&gpio_in_pd>;
			};
		};
	};
	/* GPIO that enables the LDO regulator for the LCD display */
	lcd-ldo {
		lcd_pwr_en_default_mode: lcd_pwr_en_default {
			/* LCD_PWR_EN on GPIO219 */
			gavini_cfg1 {
				pins = "GPIO219_AG10";
				ste,config = <&gpio_out_hi>;
			};
		};
	};
	/* GPIO that enables the WLAN internal LDO regulators */
	wlan-ldo {
		wlan_ldo_en_default: wlan_ldo_default {
			/* GPIO215 named WLAN_RST_N */
			gavini_cfg1 {
				pins = "GPIO215_AH13";
				ste,config = <&gpio_out_lo>;
			};
		};
	};
	/* GPIO that enables the 2.9V SD card level translator */
	sd-level-translator {
		sd_level_translator_default: sd_level_translator_default {
			/* level shifter on GPIO193 */
			skomer_cfg1 {
				pins = "GPIO193_AH27";
				ste,config = <&gpio_out_hi>;
			};
		};
	};
	/* GPIO keys */
	gpio-keys {
		gpio_keys_default_mode: gpio_keys_default {
			skomer_cfg1 {
				pins = "GPIO32_V2", /* Projector On HotKey */
				       "GPIO67_G2", /* VOL UP */
				       "GPIO91_B6", /* HOME */
				       "GPIO92_D6"; /* VOL DOWN */
				ste,config = <&gpio_in_pu>;
			};
		};
	};
	/* Interrupt line for the Atmel MXT228 touchscreen */
	tsp {
		tsp_default: tsp_default {
			gavini_cfg1 {
				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
				ste,config = <&gpio_in_nopull>;
			};
		};
	};
	/* Reset line for the Memsic MMC328 magnetometer */
	mmc328 {
		mmc328_default: mmc328_gavini {
			gavini_cfg1 {
				pins = "GPIO204_AF23";
				ste,config = <&gpio_out_hi>;
			};
		};
	};
	/* Interrupt line for Invensense MPU3050 gyroscope */
	mpu3050 {
		mpu3050_default: mpu3050 {
			gavini_cfg1 {
				/* GPIO226 used for IRQ */
				pins = "GPIO226_AF8";
				ste,config = <&gpio_in_nopull>;
			};
		};
	};
	/* GPIO-based I2C bus for magnetometer and NCP6914 */
	i2c-gpio-0 {
		i2c_gpio_0_default: i2c_gpio_0 {
			gavini_cfg1 {
				pins = "GPIO143_D12", "GPIO144_B13";
				ste,config = <&gpio_in_nopull>;
			};
		};
	};
	/* GPIO-based I2C bus for the Immersion ISA1200 */
	i2c-gpio-2 {
		i2c_gpio_2_default: i2c_gpio_2 {
			gavini_cfg1 {
				pins = "GPIO201_AF24", "GPIO202_AF25";
				ste,config = <&gpio_in_nopull>;
			};
		};
	};
	/* GPIO-based I2C bus for the TI DPP2601 */
	i2c-gpio-3 {
		i2c_gpio_3_default: i2c_gpio_3 {
			gavini_cfg1 {
				pins = "GPIO196_AG26", "GPIO197_AH24";
				ste,config = <&gpio_in_nopull>;
			};
		};
	};
	/* GPIO-based SPI bus for the display */
	spi-gpio-0 {
		spi_gpio_0_default: spi_gpio_0_d {
			gavini_cfg1 {
				pins = "GPIO220_AH10", "GPIO223_AH9", "GPIO224_AG9";
				ste,config = <&gpio_out_hi>;
			};
			gavini_cfg2 {
				pins = "GPIO225_AG8";
				ste,config = <&gpio_in_nopull>;
			};
		};
		spi_gpio_0_sleep: spi_gpio_0_s {
			gavini_cfg1 {
				pins = "GPIO220_AH10", "GPIO223_AH9",
				     "GPIO224_AG9", "GPIO225_AG8";
				ste,config = <&gpio_out_hi>;
			};
			gavini_cfg2 {
				pins = "GPIO225_AG8";
				ste,config = <&gpio_out_lo>;
			};
		};
	};
	wlan {
		wlan_default_mode: wlan_default {
			/* GPIO216 for WL_HOST_WAKE */
			gavini_cfg2 {
				pins = "GPIO216_AG12";
				ste,config = <&gpio_in_pd>;
			};
		};
	};
	bluetooth {
		bluetooth_default_mode: bluetooth_default {
			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
			gavini_cfg1 {
				pins = "GPIO199_AH23", "GPIO222_AJ9";
				ste,config = <&gpio_out_lo>;
			};
			/* GPIO97 BT_HOST_WAKE */
			gavini_cfg2 {
				pins = "GPIO97_D9";
				ste,config = <&gpio_in_nopull>;
			};
			/* GPIO209 BT_RST_N */
			gavini_cfg3 {
				pins = "GPIO209_AG15";
				ste,config = <&gpio_out_hi>;
			};
		};
	};
	/* Interrupt line for TI TSU6111 Micro USB switch */
	tsu6111 {
		tsu6111_default: tsu6111 {
			gavini_cfg1 {
				/* GPIO95 used for IRQ */
				pins = "GPIO95_E8";
				ste,config = <&gpio_in_nopull>;
			};
		};
	};
};