Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 | /* * Linux ARCnet driver - COM20020 chipset support - function declarations * * Written 1997 by David Woodhouse. * Written 1994-1999 by Avery Pennarun. * Derived from skeleton.c by Donald Becker. * * Special thanks to Contemporary Controls, Inc. (www.ccontrols.com) * for sponsoring the further development of this driver. * * ********************** * * The original copyright of skeleton.c was as follows: * * skeleton.c Written 1993 by Donald Becker. * Copyright 1993 United States Government as represented by the * Director, National Security Agency. This software may only be used * and distributed according to the terms of the GNU General Public License as * modified by SRC, incorporated herein by reference. * * ********************** * * For more details, see drivers/net/arcnet.c * * ********************** */ #ifndef __COM20020_H #define __COM20020_H int com20020_check(struct net_device *dev); int com20020_found(struct net_device *dev, int shared); extern const struct net_device_ops com20020_netdev_ops; /* The number of low I/O ports used by the card. */ #define ARCNET_TOTAL_SIZE 8 /* various register addresses */ #ifdef CONFIG_SA1100_CT6001 #define BUS_ALIGN 2 /* 8 bit device on a 16 bit bus - needs padding */ #else #define BUS_ALIGN 1 #endif #define _INTMASK (ioaddr+BUS_ALIGN*0) /* writable */ #define _STATUS (ioaddr+BUS_ALIGN*0) /* readable */ #define _COMMAND (ioaddr+BUS_ALIGN*1) /* standard arcnet commands */ #define _DIAGSTAT (ioaddr+BUS_ALIGN*1) /* diagnostic status register */ #define _ADDR_HI (ioaddr+BUS_ALIGN*2) /* control registers for IO-mapped memory */ #define _ADDR_LO (ioaddr+BUS_ALIGN*3) #define _MEMDATA (ioaddr+BUS_ALIGN*4) /* data port for IO-mapped memory */ #define _SUBADR (ioaddr+BUS_ALIGN*5) /* the extended port _XREG refers to */ #define _CONFIG (ioaddr+BUS_ALIGN*6) /* configuration register */ #define _XREG (ioaddr+BUS_ALIGN*7) /* extra registers (indexed by _CONFIG or _SUBADR) */ /* in the ADDR_HI register */ #define RDDATAflag 0x80 /* next access is a read (not a write) */ /* in the DIAGSTAT register */ #define NEWNXTIDflag 0x02 /* ID to which token is passed has changed */ /* in the CONFIG register */ #define RESETcfg 0x80 /* put card in reset state */ #define TXENcfg 0x20 /* enable TX */ /* in SETUP register */ #define PROMISCset 0x10 /* enable RCV_ALL */ #define P1MODE 0x80 /* enable P1-MODE for Backplane */ #define SLOWARB 0x01 /* enable Slow Arbitration for >=5Mbps */ /* COM2002x */ #define SUB_TENTATIVE 0 /* tentative node ID */ #define SUB_NODE 1 /* node ID */ #define SUB_SETUP1 2 /* various options */ #define SUB_TEST 3 /* test/diag register */ /* COM20022 only */ #define SUB_SETUP2 4 /* sundry options */ #define SUB_BUSCTL 5 /* bus control options */ #define SUB_DMACOUNT 6 /* DMA count options */ #define SET_SUBADR(x) do { \ if ((x) < 4) \ { \ lp->config = (lp->config & ~0x03) | (x); \ SETCONF; \ } \ else \ { \ outb(x, _SUBADR); \ } \ } while (0) #undef ARCRESET #undef ASTATUS #undef ACOMMAND #undef AINTMASK #define ARCRESET { outb(lp->config | 0x80, _CONFIG); \ udelay(5); \ outb(lp->config , _CONFIG); \ } #define ARCRESET0 { outb(0x18 | 0x80, _CONFIG); \ udelay(5); \ outb(0x18 , _CONFIG); \ } #define ASTATUS() inb(_STATUS) #define ADIAGSTATUS() inb(_DIAGSTAT) #define ACOMMAND(cmd) outb((cmd),_COMMAND) #define AINTMASK(msk) outb((msk),_INTMASK) #define SETCONF outb(lp->config, _CONFIG) #endif /* __COM20020_H */ |