/*----------------------------------------------------------------*/
/*
   Qlogic linux driver - work in progress. No Warranty express or implied.
   Use at your own risk.  Support Tort Reform so you won't have to read all
   these silly disclaimers.

   Copyright 1994, Tom Zerucha.   
   tz@execpc.com
   
   Additional Code, and much appreciated help by
   Michael A. Griffith
   grif@cs.ucr.edu

   Thanks to Eric Youngdale and Dave Hinds for loadable module and PCMCIA
   help respectively, and for suffering through my foolishness during the
   debugging process.

   Reference Qlogic FAS408 Technical Manual, 53408-510-00A, May 10, 1994
   (you can reference it, but it is incomplete and inaccurate in places)

   Version 0.46 1/30/97 - kernel 1.2.0+

   Functions as standalone, loadable, and PCMCIA driver, the latter from
   Dave Hinds' PCMCIA package.
   
   Cleaned up 26/10/2002 by Alan Cox <alan@redhat.com> as part of the 2.5
   SCSI driver cleanup and audit. This driver still needs work on the
   following
   	-	Non terminating hardware waits
   	-	Support multiple cards at a time
   	-	Some layering violations with its pcmcia stub

   Redistributable under terms of the GNU General Public License

   For the avoidance of doubt the "preferred form" of this code is one which
   is in an open non patent encumbered format. Where cryptographic key signing
   forms part of the process of creating an executable the information
   including keys needed to generate an equivalently functional executable
   are deemed to be part of the source code.

*/
/*----------------------------------------------------------------*/
/* Configuration */

/* Set the following to 2 to use normal interrupt (active high/totempole-
   tristate), otherwise use 0 (REQUIRED FOR PCMCIA) for active low, open
   drain */

#define QL_INT_ACTIVE_HIGH 2

/* Set the following to 1 to enable the use of interrupts.  Note that 0 tends
   to be more stable, but slower (or ties up the system more) */

#define QL_USE_IRQ 1

/* Set the following to max out the speed of the PIO PseudoDMA transfers,
   again, 0 tends to be slower, but more stable.  */

#define QL_TURBO_PDMA 1

/* This should be 1 to enable parity detection */

#define QL_ENABLE_PARITY 1

/* This will reset all devices when the driver is initialized (during bootup).
   The other linux drivers don't do this, but the DOS drivers do, and after
   using DOS or some kind of crash or lockup this will bring things back
   without requiring a cold boot.  It does take some time to recover from a
   reset, so it is slower, and I have seen timeouts so that devices weren't
   recognized when this was set. */

#define QL_RESET_AT_START 0

/* crystal frequency in megahertz (for offset 5 and 9)
   Please set this for your card.  Most Qlogic cards are 40 Mhz.  The
   Control Concepts ISA (not VLB) is 24 Mhz */

#define XTALFREQ	40

/**********/
/* DANGER! modify these at your own risk */
/* SLOWCABLE can usually be reset to zero if you have a clean setup and
   proper termination.  The rest are for synchronous transfers and other
   advanced features if your device can transfer faster than 5Mb/sec.
   If you are really curious, email me for a quick howto until I have
   something official */
/**********/

/*****/
/* config register 1 (offset 8) options */
/* This needs to be set to 1 if your cabling is long or noisy */
#define SLOWCABLE 1

/*****/
/* offset 0xc */
/* This will set fast (10Mhz) synchronous timing when set to 1
   For this to have an effect, FASTCLK must also be 1 */
#define FASTSCSI 0

/* This when set to 1 will set a faster sync transfer rate */
#define FASTCLK 0	/*(XTALFREQ>25?1:0)*/

/*****/
/* offset 6 */
/* This is the sync transfer divisor, XTALFREQ/X will be the maximum
   achievable data rate (assuming the rest of the system is capable
   and set properly) */
#define SYNCXFRPD 5	/*(XTALFREQ/5)*/

/*****/
/* offset 7 */
/* This is the count of how many synchronous transfers can take place
	i.e. how many reqs can occur before an ack is given.
	The maximum value for this is 15, the upper bits can modify
	REQ/ACK assertion and deassertion during synchronous transfers
	If this is 0, the bus will only transfer asynchronously */
#define SYNCOFFST 0
/* for the curious, bits 7&6 control the deassertion delay in 1/2 cycles
	of the 40Mhz clock. If FASTCLK is 1, specifying 01 (1/2) will
	cause the deassertion to be early by 1/2 clock.  Bits 5&4 control
	the assertion delay, also in 1/2 clocks (FASTCLK is ignored here). */

/*----------------------------------------------------------------*/
#ifdef PCMCIA
#undef QL_INT_ACTIVE_HIGH
#define QL_INT_ACTIVE_HIGH 0
#endif

#include <linux/module.h>
#include <linux/blkdev.h>		/* to get disk capacity */
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/proc_fs.h>
#include <linux/unistd.h>
#include <linux/spinlock.h>
#include <linux/stat.h>

#include <asm/io.h>
#include <asm/irq.h>
#include <asm/dma.h>

#include "scsi.h"
#include "hosts.h"

/*----------------------------------------------------------------*/
/* driver state info, local to driver */
static int qbase;		/* Port */
static int qinitid;		/* initiator ID */
static int qabort;		/* Flag to cause an abort */
static int qlirq = -1;		/* IRQ being used */
static char qinfo[80];		/* description */
static Scsi_Cmnd *qlcmd;	/* current command being processed */

static int qlcfg5 = (XTALFREQ << 5);	/* 15625/512 */
static int qlcfg6 = SYNCXFRPD;
static int qlcfg7 = SYNCOFFST;
static int qlcfg8 = (SLOWCABLE << 7) | (QL_ENABLE_PARITY << 4);
static int qlcfg9 = ((XTALFREQ + 4) / 5);
static int qlcfgc = (FASTCLK << 3) | (FASTSCSI << 4);

int qlogicfas_queuecommand(Scsi_Cmnd * cmd, void (*done) (Scsi_Cmnd *));

/*----------------------------------------------------------------*/
/* The qlogic card uses two register maps - These macros select which one */
#define REG0 ( outb( inb( qbase + 0xd ) & 0x7f , qbase + 0xd ), outb( 4 , qbase + 0xd ))
#define REG1 ( outb( inb( qbase + 0xd ) | 0x80 , qbase + 0xd ), outb( 0xb4 | QL_INT_ACTIVE_HIGH , qbase + 0xd ))

/* following is watchdog timeout in microseconds */
#define WATCHDOG 5000000

/*----------------------------------------------------------------*/
/* the following will set the monitor border color (useful to find
   where something crashed or gets stuck at and as a simple profiler) */

#if 0
#define rtrc(i) {inb(0x3da);outb(0x31,0x3c0);outb((i),0x3c0);}
#else
#define rtrc(i) {}
#endif

/*----------------------------------------------------------------*/
/* local functions */
/*----------------------------------------------------------------*/

/* error recovery - reset everything */

static void ql_zap(void)
{
	int x;

	x = inb(qbase + 0xd);
	REG0;
	outb(3, qbase + 3);	/* reset SCSI */
	outb(2, qbase + 3);	/* reset chip */
	if (x & 0x80)
		REG1;
}

/*
 *	Do a pseudo-dma tranfer
 */
 
static int ql_pdma(int phase, char *request, int reqlen)
{
	int j;
	j = 0;
	if (phase & 1) {	/* in */
#if QL_TURBO_PDMA
		rtrc(4)
		/* empty fifo in large chunks */
		if (reqlen >= 128 && (inb(qbase + 8) & 2)) {	/* full */
			insl(qbase + 4, request, 32);
			reqlen -= 128;
			request += 128;
		}
		while (reqlen >= 84 && !(j & 0xc0))	/* 2/3 */
			if ((j = inb(qbase + 8)) & 4) 
			{
				insl(qbase + 4, request, 21);
				reqlen -= 84;
				request += 84;
			}
		if (reqlen >= 44 && (inb(qbase + 8) & 8)) {	/* 1/3 */
			insl(qbase + 4, request, 11);
			reqlen -= 44;
			request += 44;
		}
#endif
		/* until both empty and int (or until reclen is 0) */
		rtrc(7)
		j = 0;
		while (reqlen && !((j & 0x10) && (j & 0xc0))) 
		{
			/* while bytes to receive and not empty */
			j &= 0xc0;
			while (reqlen && !((j = inb(qbase + 8)) & 0x10)) 
			{
				*request++ = inb(qbase + 4);
				reqlen--;
			}
			if (j & 0x10)
				j = inb(qbase + 8);

		}
	} else {		/* out */
#if QL_TURBO_PDMA
		rtrc(4)
		    if (reqlen >= 128 && inb(qbase + 8) & 0x10) {	/* empty */
			outsl(qbase + 4, request, 32);
			reqlen -= 128;
			request += 128;
		}
		while (reqlen >= 84 && !(j & 0xc0))	/* 1/3 */
			if (!((j = inb(qbase + 8)) & 8)) {
				outsl(qbase + 4, request, 21);
				reqlen -= 84;
				request += 84;
			}
		if (reqlen >= 40 && !(inb(qbase + 8) & 4)) {	/* 2/3 */
			outsl(qbase + 4, request, 10);
			reqlen -= 40;
			request += 40;
		}
#endif
		/* until full and int (or until reclen is 0) */
		rtrc(7)
		    j = 0;
		while (reqlen && !((j & 2) && (j & 0xc0))) {
			/* while bytes to send and not full */
			while (reqlen && !((j = inb(qbase + 8)) & 2)) 
			{
				outb(*request++, qbase + 4);
				reqlen--;
			}
			if (j & 2)
				j = inb(qbase + 8);
		}
	}
	/* maybe return reqlen */
	return inb(qbase + 8) & 0xc0;
}

/*
 *	Wait for interrupt flag (polled - not real hardware interrupt) 
 */

static int ql_wai(void)
{
	int k;
	unsigned long i;

	k = 0;
	i = jiffies + WATCHDOG;
	while (time_before(jiffies, i) && !qabort && !((k = inb(qbase + 4)) & 0xe0)) {
		barrier();
		cpu_relax();
	}
	if (time_after_eq(jiffies, i))
		return (DID_TIME_OUT);
	if (qabort)
		return (qabort == 1 ? DID_ABORT : DID_RESET);
	if (k & 0x60)
		ql_zap();
	if (k & 0x20)
		return (DID_PARITY);
	if (k & 0x40)
		return (DID_ERROR);
	return 0;
}

/*
 *	Initiate scsi command - queueing handler 
 *	caller must hold host lock
 */

static void ql_icmd(Scsi_Cmnd * cmd)
{
	unsigned int i;

	qabort = 0;

	REG0;
	/* clearing of interrupts and the fifo is needed */

	inb(qbase + 5);		/* clear interrupts */
	if (inb(qbase + 5))	/* if still interrupting */
		outb(2, qbase + 3);	/* reset chip */
	else if (inb(qbase + 7) & 0x1f)
		outb(1, qbase + 3);	/* clear fifo */
	while (inb(qbase + 5));	/* clear ints */
	REG1;
	outb(1, qbase + 8);	/* set for PIO pseudo DMA */
	outb(0, qbase + 0xb);	/* disable ints */
	inb(qbase + 8);		/* clear int bits */
	REG0;
	outb(0x40, qbase + 0xb);	/* enable features */

	/* configurables */
	outb(qlcfgc, qbase + 0xc);
	/* config: no reset interrupt, (initiator) bus id */
	outb(0x40 | qlcfg8 | qinitid, qbase + 8);
	outb(qlcfg7, qbase + 7);
	outb(qlcfg6, qbase + 6);
	 /**/ outb(qlcfg5, qbase + 5);	/* select timer */
	outb(qlcfg9 & 7, qbase + 9);	/* prescaler */
/*	outb(0x99, qbase + 5);	*/
	outb(cmd->device->id, qbase + 4);

	for (i = 0; i < cmd->cmd_len; i++)
		outb(cmd->cmnd[i], qbase + 2);

	qlcmd = cmd;
	outb(0x41, qbase + 3);	/* select and send command */
}

/*
 *	Process scsi command - usually after interrupt 
 */

static unsigned int ql_pcmd(Scsi_Cmnd * cmd)
{
	unsigned int i, j;
	unsigned long k;
	unsigned int result;	/* ultimate return result */
	unsigned int status;	/* scsi returned status */
	unsigned int message;	/* scsi returned message */
	unsigned int phase;	/* recorded scsi phase */
	unsigned int reqlen;	/* total length of transfer */
	struct scatterlist *sglist;	/* scatter-gather list pointer */
	unsigned int sgcount;	/* sg counter */
	char *buf;

	rtrc(1)
	j = inb(qbase + 6);
	i = inb(qbase + 5);
	if (i == 0x20) {
		return (DID_NO_CONNECT << 16);
	}
	i |= inb(qbase + 5);	/* the 0x10 bit can be set after the 0x08 */
	if (i != 0x18) {
		printk(KERN_ERR "Ql:Bad Interrupt status:%02x\n", i);
		ql_zap();
		return (DID_BAD_INTR << 16);
	}
	j &= 7;			/* j = inb( qbase + 7 ) >> 5; */

	/* correct status is supposed to be step 4 */
	/* it sometimes returns step 3 but with 0 bytes left to send */
	/* We can try stuffing the FIFO with the max each time, but we will get a
	   sequence of 3 if any bytes are left (but we do flush the FIFO anyway */

	if (j != 3 && j != 4) {
		printk(KERN_ERR "Ql:Bad sequence for command %d, int %02X, cmdleft = %d\n",
		     j, i, inb(qbase + 7) & 0x1f);
		ql_zap();
		return (DID_ERROR << 16);
	}
	result = DID_OK;
	if (inb(qbase + 7) & 0x1f)	/* if some bytes in fifo */
		outb(1, qbase + 3);	/* clear fifo */
	/* note that request_bufflen is the total xfer size when sg is used */
	reqlen = cmd->request_bufflen;
	/* note that it won't work if transfers > 16M are requested */
	if (reqlen && !((phase = inb(qbase + 4)) & 6)) {	/* data phase */
		rtrc(2)
		outb(reqlen, qbase);	/* low-mid xfer cnt */
		outb(reqlen >> 8, qbase + 1);	/* low-mid xfer cnt */
		outb(reqlen >> 16, qbase + 0xe);	/* high xfer cnt */
		outb(0x90, qbase + 3);	/* command do xfer */
		/* PIO pseudo DMA to buffer or sglist */
		REG1;
		if (!cmd->use_sg)
			ql_pdma(phase, cmd->request_buffer,
				cmd->request_bufflen);
		else {
			sgcount = cmd->use_sg;
			sglist = cmd->request_buffer;
			while (sgcount--) {
				if (qabort) {
					REG0;
					return ((qabort == 1 ? DID_ABORT : DID_RESET) << 16);
				}
				buf = page_address(sglist->page) + sglist->offset;
				if (ql_pdma(phase, buf, sglist->length))
					break;
				sglist++;
			}
		}
		REG0;
		rtrc(2)
		/*
		 *	Wait for irq (split into second state of irq handler
		 *	if this can take time) 
		 */
		if ((k = ql_wai()))
			return (k << 16);
		k = inb(qbase + 5);	/* should be 0x10, bus service */
	}

	/*
	 *	Enter Status (and Message In) Phase 
	 */
	 
	k = jiffies + WATCHDOG;

	while (time_before(jiffies, k) && !qabort && !(inb(qbase + 4) & 6))
		cpu_relax();	/* wait for status phase */

	if (time_after_eq(jiffies, k)) {
		ql_zap();
		return (DID_TIME_OUT << 16);
	}

	/* FIXME: timeout ?? */
	while (inb(qbase + 5))
		cpu_relax();	/* clear pending ints */

	if (qabort)
		return ((qabort == 1 ? DID_ABORT : DID_RESET) << 16);

	outb(0x11, qbase + 3);	/* get status and message */
	if ((k = ql_wai()))
		return (k << 16);
	i = inb(qbase + 5);	/* get chip irq stat */
	j = inb(qbase + 7) & 0x1f;	/* and bytes rec'd */
	status = inb(qbase + 2);
	message = inb(qbase + 2);

	/*
	 *	Should get function complete int if Status and message, else 
	 *	bus serv if only status 
	 */
	if (!((i == 8 && j == 2) || (i == 0x10 && j == 1))) {
		printk(KERN_ERR "Ql:Error during status phase, int=%02X, %d bytes recd\n", i, j);
		result = DID_ERROR;
	}
	outb(0x12, qbase + 3);	/* done, disconnect */
	rtrc(1)
	if ((k = ql_wai()))
		return (k << 16);

	/*
	 *	Should get bus service interrupt and disconnect interrupt 
	 */
	 
	i = inb(qbase + 5);	/* should be bus service */
	while (!qabort && ((i & 0x20) != 0x20)) {
		barrier();
		cpu_relax();
		i |= inb(qbase + 5);
	}
	rtrc(0)

	if (qabort)
		return ((qabort == 1 ? DID_ABORT : DID_RESET) << 16);
		
	return (result << 16) | (message << 8) | (status & STATUS_MASK);
}

#if QL_USE_IRQ

/*
 *	Interrupt handler 
 */

static void ql_ihandl(int irq, void *dev_id, struct pt_regs *regs)
{
	Scsi_Cmnd *icmd;
	REG0;

	if (!(inb(qbase + 4) & 0x80))	/* false alarm? */
		return;

	if (qlcmd == NULL) {	/* no command to process? */
		int i;
		i = 16;
		while (i-- && inb(qbase + 5));	/* maybe also ql_zap() */
		return;
	}
	icmd = qlcmd;
	icmd->result = ql_pcmd(icmd);
	qlcmd = NULL;
	/*
	 *	If result is CHECK CONDITION done calls qcommand to request 
	 *	sense 
	 */
	(icmd->scsi_done) (icmd);
}

static irqreturn_t do_ql_ihandl(int irq, void *dev_id, struct pt_regs *regs)
{
	unsigned long flags;
	struct Scsi_Host *host = dev_id;

	spin_lock_irqsave(host->host_lock, flags);
	ql_ihandl(irq, dev_id, regs);
	spin_unlock_irqrestore(host->host_lock, flags);
	return IRQ_HANDLED;
}

#endif

#if QL_USE_IRQ

/*
 *	Queued command
 */

int qlogicfas_queuecommand(Scsi_Cmnd * cmd, void (*done) (Scsi_Cmnd *))
{
	if (cmd->device->id == qinitid) {
		cmd->result = DID_BAD_TARGET << 16;
		done(cmd);
		return 0;
	}

	cmd->scsi_done = done;
	/* wait for the last command's interrupt to finish */
	while (qlcmd != NULL) {
		barrier();
		cpu_relax();
	}
	ql_icmd(cmd);
	return 0;
}
#else
int qlogicfas_queuecommand(Scsi_Cmnd * cmd, void (*done) (Scsi_Cmnd *))
{
	return 1;
}
#endif

#ifdef PCMCIA

/*
 *	Allow PCMCIA code to preset the port
 *	port should be 0 and irq to -1 respectively for autoprobing 
 */

void qlogicfas_preset(int port, int irq)
{
	qbase = port;
	qlirq = irq;
}

#endif

/*
 *	Look for qlogic card and init if found 
 */
 
struct Scsi_Host *__qlogicfas_detect(Scsi_Host_Template *host)
{
	int i, j;		/* these are only used by IRQ detect */
	int qltyp;		/* type of chip */
	struct Scsi_Host *hreg;	/* registered host structure */

	/*	Qlogic Cards only exist at 0x230 or 0x330 (the chip itself
	 *	decodes the address - I check 230 first since MIDI cards are
	 *	typically at 0x330
	 *
	 *	Theoretically, two Qlogic cards can coexist in the same system.
	 *	This should work by simply using this as a loadable module for
	 *	the second card, but I haven't tested this.
	 */

	if (!qbase) {
		for (qbase = 0x230; qbase < 0x430; qbase += 0x100) {
			if (!request_region(qbase, 0x10, "qlogicfas"))
				continue;
			REG1;
			if (((inb(qbase + 0xe) ^ inb(qbase + 0xe)) == 7)
			    && ((inb(qbase + 0xe) ^ inb(qbase + 0xe)) == 7))
				break;
			release_region(qbase, 0x10);
		}
		if (qbase == 0x430)
			return NULL;;
	} else
		printk(KERN_INFO "Ql: Using preset base address of %03x\n", qbase);

	qltyp = inb(qbase + 0xe) & 0xf8;
	qinitid = host->this_id;
	if (qinitid < 0)
		qinitid = 7;	/* if no ID, use 7 */
	outb(1, qbase + 8);	/* set for PIO pseudo DMA */
	REG0;
	outb(0x40 | qlcfg8 | qinitid, qbase + 8);	/* (ini) bus id, disable scsi rst */
	outb(qlcfg5, qbase + 5);	/* select timer */
	outb(qlcfg9, qbase + 9);	/* prescaler */

#if QL_RESET_AT_START
	outb(3, qbase + 3);
	REG1;
	/* FIXME: timeout */
	while (inb(qbase + 0xf) & 4)
		cpu_relax();
	REG0;
#endif

#if QL_USE_IRQ
	/*
	 *	IRQ probe - toggle pin and check request pending 
	 */

	if (qlirq == -1) {
		i = 0xffff;
		j = 3;
		outb(0x90, qbase + 3);	/* illegal command - cause interrupt */
		REG1;
		outb(10, 0x20);	/* access pending interrupt map */
		outb(10, 0xa0);
		while (j--) {
			outb(0xb0 | QL_INT_ACTIVE_HIGH, qbase + 0xd);	/* int pin off */
			i &= ~(inb(0x20) | (inb(0xa0) << 8));		/* find IRQ off */
			outb(0xb4 | QL_INT_ACTIVE_HIGH, qbase + 0xd);	/* int pin on */
			i &= inb(0x20) | (inb(0xa0) << 8);		/* find IRQ on */
		}
		REG0;
		while (inb(qbase + 5));	/* purge int */
		j = -1;
		while (i)	/* find on bit */
			i >>= 1, j++;	/* should check for exactly 1 on */
		qlirq = j;
	} else
		printk(KERN_INFO "Ql: Using preset IRQ %d\n", qlirq);

	if (qlirq >= 0 && !request_irq(qlirq, do_ql_ihandl, 0, "qlogicfas", NULL))
		host->can_queue = 1;
#endif
	hreg = scsi_register(host, 0);	/* no host data */
	if (!hreg)
		goto err_release_mem;
	hreg->io_port = qbase;
	hreg->n_io_port = 16;
	hreg->dma_channel = -1;
	if (qlirq != -1)
		hreg->irq = qlirq;

	sprintf(qinfo,
		"Qlogicfas Driver version 0.46, chip %02X at %03X, IRQ %d, TPdma:%d",
		qltyp, qbase, qlirq, QL_TURBO_PDMA);
	host->name = qinfo;

	return hreg;

err_release_mem:
	release_region(qbase, 0x10);
	if (host->can_queue)
		free_irq(qlirq, do_ql_ihandl);
	return NULL;;

}

int __devinit qlogicfas_detect(Scsi_Host_Template *sht)
{
	return (__qlogicfas_detect(sht) != NULL);
}

static int qlogicfas_release(struct Scsi_Host *shost)
{
	if (shost->irq)
		free_irq(shost->irq, NULL);
	if (shost->dma_channel != 0xff)
		free_dma(shost->dma_channel);
	if (shost->io_port && shost->n_io_port)
		release_region(shost->io_port, shost->n_io_port);
	scsi_unregister(shost);
	return 0;
}

/* 
 *	Return bios parameters 
 */

int qlogicfas_biosparam(struct scsi_device * disk,
		        struct block_device *dev,
			sector_t capacity, int ip[])
{
/* This should mimic the DOS Qlogic driver's behavior exactly */
	ip[0] = 0x40;
	ip[1] = 0x20;
	ip[2] = (unsigned long) capacity / (ip[0] * ip[1]);
	if (ip[2] > 1024) {
		ip[0] = 0xff;
		ip[1] = 0x3f;
		ip[2] = (unsigned long) capacity / (ip[0] * ip[1]);
#if 0
		if (ip[2] > 1023)
			ip[2] = 1023;
#endif
	}
	return 0;
}

/*
 *	Abort a command in progress
 */
 
static int qlogicfas_abort(Scsi_Cmnd * cmd)
{
	qabort = 1;
	ql_zap();
	return SUCCESS;
}

/* 
 *	Reset SCSI bus
 *	FIXME: This function is invoked with cmd = NULL directly by
 *	the PCMCIA qlogic_stub code. This wants fixing
 */

int qlogicfas_bus_reset(Scsi_Cmnd * cmd)
{
	qabort = 2;
	ql_zap();
	return SUCCESS;
}

/* 
 *	Reset SCSI host controller
 */

static int qlogicfas_host_reset(Scsi_Cmnd * cmd)
{
	return FAILED;
}

/* 
 *	Reset SCSI device
 */

static int qlogicfas_device_reset(Scsi_Cmnd * cmd)
{
	return FAILED;
}

/*
 *	Return info string
 */

static const char *qlogicfas_info(struct Scsi_Host *host)
{
	return qinfo;
}

MODULE_AUTHOR("Tom Zerucha, Michael Griffith");
MODULE_DESCRIPTION("Driver for the Qlogic FAS SCSI controllers");
MODULE_LICENSE("GPL");

/*
 *	The driver template is also needed for PCMCIA
 */
Scsi_Host_Template qlogicfas_driver_template = {
	.module			= THIS_MODULE,
	.name			= "qlogicfas",
	.proc_name		= "qlogicfas",
	.detect			= qlogicfas_detect,
	.release		= qlogicfas_release,
	.info			= qlogicfas_info,
	.queuecommand		= qlogicfas_queuecommand,
	.eh_abort_handler	= qlogicfas_abort,
	.eh_bus_reset_handler	= qlogicfas_bus_reset,
	.eh_device_reset_handler= qlogicfas_device_reset,
	.eh_host_reset_handler	= qlogicfas_host_reset,
	.bios_param		= qlogicfas_biosparam,
	.can_queue		= 0,
	.this_id		= -1,
	.sg_tablesize		= SG_ALL,
	.cmd_per_lun		= 1,
	.use_clustering		= DISABLE_CLUSTERING,
};

#ifndef PCMCIA
#define driver_template qlogicfas_driver_template
#include "scsi_module.c"
#endif