Loading...
/* * arch/ppc/platforms/ebony.h * * Ebony board definitions * * Matt Porter <mporter@mvista.com> * * Copyright 2002 MontaVista Software Inc. * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. */ #ifdef __KERNEL__ #ifndef __ASM_EBONY_H__ #define __ASM_EBONY_H__ #include <linux/config.h> #include <platforms/4xx/ibm440gp.h> /* F/W TLB mapping used in bootloader glue to reset EMAC */ #define PPC44x_EMAC0_MR0 0xE0000800 /* Macros to get at Ebony VPD info */ #define EBONY_VPD_BASE 0x00000001fffffe00ULL #define EBONY_VPD_SIZE 0x24 #define EBONY_NA0_OFFSET 0x0c #define EBONY_NA1_OFFSET 0x18 #define EBONY_NA0_ADDR(base) (base + EBONY_NA0_OFFSET) #define EBONY_NA1_ADDR(base) (base + EBONY_NA1_OFFSET) /* Default clock rates for Rev. B and Rev. C silicon */ #define EBONY_440GP_RB_SYSCLK 33000000 #define EBONY_440GP_RC_SYSCLK 400000000 /* RTC/NVRAM location */ #define EBONY_RTC_ADDR 0x0000000148000000ULL #define EBONY_RTC_SIZE 0x2000 /* Flash */ #define EBONY_FPGA_ADDR 0x0000000148300000ULL #define EBONY_BOOT_SMALL_FLASH(x) (x & 0x20) #define EBONY_ONBRD_FLASH_EN(x) (x & 0x02) #define EBONY_FLASH_SEL(x) (x & 0x01) #define EBONY_SMALL_FLASH_LOW1 0x00000001ff800000ULL #define EBONY_SMALL_FLASH_LOW2 0x00000001ff880000ULL #define EBONY_SMALL_FLASH_HIGH1 0x00000001fff00000ULL #define EBONY_SMALL_FLASH_HIGH2 0x00000001fff80000ULL #define EBONY_SMALL_FLASH_SIZE 0x80000 #define EBONY_LARGE_FLASH_LOW 0x00000001ff800000ULL #define EBONY_LARGE_FLASH_HIGH 0x00000001ffc00000ULL #define EBONY_LARGE_FLASH_SIZE 0x400000 #define EBONY_SMALL_FLASH_BASE 0x00000001fff80000ULL #define EBONY_LARGE_FLASH_BASE 0x00000001ff800000ULL /* * Serial port defines */ /* OpenBIOS defined UART mappings, used before early_serial_setup */ #define UART0_IO_BASE 0xE0000200 #define UART1_IO_BASE 0xE0000300 /* external Epson SG-615P */ #define BASE_BAUD 691200 #define STD_UART_OP(num) \ { 0, BASE_BAUD, 0, UART##num##_INT, \ (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST), \ iomem_base: UART##num##_IO_BASE, \ io_type: SERIAL_IO_MEM}, #define SERIAL_PORT_DFNS \ STD_UART_OP(0) \ STD_UART_OP(1) /* PCI support */ #define EBONY_PCI_LOWER_IO 0x00000000 #define EBONY_PCI_UPPER_IO 0x0000ffff #define EBONY_PCI_LOWER_MEM 0x80002000 #define EBONY_PCI_UPPER_MEM 0xffffefff #define EBONY_PCI_CFGREGS_BASE 0x000000020ec00000 #define EBONY_PCI_CFGA_PLB32 0x0ec00000 #define EBONY_PCI_CFGD_PLB32 0x0ec00004 #define EBONY_PCI_IO_BASE 0x0000000208000000ULL #define EBONY_PCI_IO_SIZE 0x00010000 #define EBONY_PCI_MEM_OFFSET 0x00000000 #endif /* __ASM_EBONY_H__ */ #endif /* __KERNEL__ */ |