Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 | /* * include/asm-ppc/pc_serial.h * * This is basically a copy of include/asm-i386/serial.h. * It is used on platforms which have an ISA bus and thus are likely * to have PC-style serial ports at the legacy I/O port addresses. * It also includes the definitions for the fourport, accent, boca * and hub6 multiport serial cards, although I have never heard of * anyone using any of those on a PPC platform. -- paulus */ #include <linux/config.h> /* * This assumes you have a 1.8432 MHz clock for your UART. * * It'd be nice if someone built a serial card with a 24.576 MHz * clock, since the 16550A is capable of handling a top speed of 1.5 * megabits/second; but this requires the faster clock. */ #define BASE_BAUD ( 1843200 / 16 ) #ifdef CONFIG_SERIAL_MANY_PORTS #define RS_TABLE_SIZE 64 #else #define RS_TABLE_SIZE 4 #endif /* Standard COM flags (except for COM4, because of the 8514 problem) */ #ifdef CONFIG_SERIAL_DETECT_IRQ #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ) #define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ) #else #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST) #define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF #endif #ifdef CONFIG_SERIAL_MANY_PORTS #define FOURPORT_FLAGS ASYNC_FOURPORT #define ACCENT_FLAGS 0 #define BOCA_FLAGS 0 #define HUB6_FLAGS 0 #endif /* * The following define the access methods for the HUB6 card. All * access is through two ports for all 24 possible chips. The card is * selected through the high 2 bits, the port on that card with the * "middle" 3 bits, and the register on that port with the bottom * 3 bits. * * While the access port and interrupt is configurable, the default * port locations are 0x302 for the port control register, and 0x303 * for the data read/write register. Normally, the interrupt is at irq3 * but can be anything from 3 to 7 inclusive. Note that using 3 will * require disabling com2. */ #define C_P(card,port) (((card)<<6|(port)<<3) + 1) #define STD_SERIAL_PORT_DEFNS \ /* UART CLK PORT IRQ FLAGS */ \ { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \ { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \ { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \ { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */ #ifdef CONFIG_SERIAL_MANY_PORTS #define EXTRA_SERIAL_PORT_DEFNS \ { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \ { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \ { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \ { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \ { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \ { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \ { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \ { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \ { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \ { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \ { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \ { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \ { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \ { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \ { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \ { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \ { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \ { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \ { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \ { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \ { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \ { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \ { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \ { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \ { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \ { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \ { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \ { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */ #else #define EXTRA_SERIAL_PORT_DEFNS #endif /* You can have up to four HUB6's in the system, but I've only * included two cards here for a total of twelve ports. */ #if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS)) #define HUB6_SERIAL_PORT_DFNS \ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */ #else #define HUB6_SERIAL_PORT_DFNS #endif #define SERIAL_PORT_DFNS \ STD_SERIAL_PORT_DEFNS \ EXTRA_SERIAL_PORT_DEFNS \ HUB6_SERIAL_PORT_DFNS |