Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 | /*****************************************************************************/ /* * crt0_ram.S -- startup code for MCF5307 ColdFire Arnewsh board. * * (C) Copyright 1999-2002, Greg Ungerer (gerg@snapgear.com). * Copyright (C) 2000 Lineo Inc. (www.lineo.com) * * 1999/02/24 Modified for the 5307 processor David W. Miller */ /*****************************************************************************/ #include "linux/autoconf.h" #include "asm/coldfire.h" #include "asm/mcfsim.h" #include "asm/nettel.h" /*****************************************************************************/ /* * SnapGear/NETtel board memory setup. */ #define MEM_BASE 0x00000000 /* Memory base at address 0 */ #define MEM_SIZE 0x00800000 /* Memory size 8Mb */ #define VBR_BASE MEM_BASE /* Vector address */ /*****************************************************************************/ .global _start .global _rambase .global _ramvec .global _ramstart .global _ramend /*****************************************************************************/ .data /* * Set up the usable of RAM stuff. Size of RAM is determined then * an initial stack set up at the end. */ _rambase: .long 0 _ramvec: .long 0 _ramstart: .long 0 _ramend: .long 0 /*****************************************************************************/ .text /* * This is the codes first entry point. This is where it all * begins... */ _start: nop /* Filler */ move.w #0x2700, %sr /* No interrupts */ /* * Setup VBR here, otherwise buserror remap will not work. * if dBug was active before (on my SBC with dBug 1.1 of Dec 16 1996) * * bkr@cut.de 19990306 * * Note: this is because dBUG points VBR to ROM, making vectors read * only, so the bus trap can't be changed. (RS) */ move.l #VBR_BASE, %a7 /* Note VBR can't be read */ movec %a7, %VBR move.l %a7, _ramvec /* Set up vector addr */ move.l %a7, _rambase /* Set up base RAM addr */ /* * Determine size of RAM, then set up initial stack. */ move.l #MEM_SIZE, %a0 move.l %a0, %d0 /* Mem end addr is in a0 */ move.l %d0, %sp /* Set up initial stack ptr */ move.l %d0, _ramend /* Set end ram addr */ /* make region ROM cachable (turn off for flash programming?) */ /* 0xff000000 - 0xffffffff */ #ifdef DEBUGGER_COMPATIBLE_CACHE movl #(0xff<<ACR_BASE_POS)+(0<<ACR_MASK_POS)+ACR_ENABLE+ACR_ANY+ACR_CM_WTHRU+ACR_WPROTECT,%d0 #else movl #(0xff<<ACR_BASE_POS)+(0<<ACR_MASK_POS)+ACR_ENABLE+ACR_ANY+ACR_CM_WBACK+ACR_WPROTECT,%d0 #endif movc %d0,%ACR0 /* make region RAM cachable * /* 0x00000000 - 0x00ffffffff */ #ifdef DEBUGGER_COMPATIBLE_CACHE movl #(0x00<<ACR_BASE_POS)+(0<<ACR_MASK_POS)+ACR_ENABLE+ACR_ANY+ACR_CM_WTHRU,%d0 #else movl #(0x00<<ACR_BASE_POS)+(0<<ACR_MASK_POS)+ACR_ENABLE+ACR_ANY+ACR_CM_WBACK,%d0 #endif movc %d0,%ACR1 /* make the default cache mode precise */ movl #CACR_EC+CACR_ESB+CACR_DCM_OFF_PRE,%d0 /* enable cache */ movc %d0,%CACR nop #ifdef CONFIG_ROMFS_FS /* * Move ROM filesystem above bss :-) */ lea.l _sbss, %a0 /* Get start of bss */ lea.l _ebss, %a1 /* Set up destination */ move.l %a0, %a2 /* Copy of bss start */ move.l 8(%a0), %d0 /* Get size of ROMFS */ addq.l #8, %d0 /* Allow for rounding */ and.l #0xfffffffc, %d0 /* Whole words */ add.l %d0, %a0 /* Copy from end */ add.l %d0, %a1 /* Copy from end */ move.l %a1, _ramstart /* Set start of ram */ _copy_romfs: move.l -(%a0), %d0 /* Copy dword */ move.l %d0, -(%a1) cmp.l %a0, %a2 /* Check if at end */ bne _copy_romfs #else /* CONFIG_ROMFS_FS */ lea.l _ebss, %a1 move.l %a1, _ramstart #endif /* CONFIG_ROMFS_FS */ /* * Zero out the bss region. */ lea.l _sbss, %a0 /* Get start of bss */ lea.l _ebss, %a1 /* Get end of bss */ clr.l %d0 /* Set value */ _clear_bss: move.l %d0, (%a0)+ /* Clear each word */ cmp.l %a0, %a1 /* Check if at end */ bne _clear_bss /* * load the current task pointer and stack */ lea init_thread_union, %a0 lea 0x2000(%a0), %sp /* * Assember start up done, start code proper. */ jsr start_kernel /* Start Linux kernel */ _exit: jmp _exit /* Should never get here */ /*****************************************************************************/ |