Loading...
# # ATM device configuration # mainmenu_option next_comment comment 'ATM drivers' if [ "$CONFIG_INET" = "y" ]; then tristate 'ATM over TCP' CONFIG_ATM_TCP fi if [ "$CONFIG_PCI" = "y" ]; then tristate 'Efficient Networks ENI155P' CONFIG_ATM_ENI if [ "$CONFIG_ATM_ENI" != "n" ]; then bool ' Enable extended debugging' CONFIG_ATM_ENI_DEBUG bool ' Fine-tune burst settings' CONFIG_ATM_ENI_TUNE_BURST if [ "$CONFIG_ATM_ENI_TUNE_BURST" = "y" ]; then bool ' Enable 16W TX bursts (discouraged)' CONFIG_ATM_ENI_BURST_TX_16W bool ' Enable 8W TX bursts (recommended)' CONFIG_ATM_ENI_BURST_TX_8W bool ' Enable 4W TX bursts (optional)' CONFIG_ATM_ENI_BURST_TX_4W bool ' Enable 2W TX bursts (optional)' CONFIG_ATM_ENI_BURST_TX_2W bool ' Enable 16W RX bursts (discouraged)' CONFIG_ATM_ENI_BURST_RX_16W bool ' Enable 8W RX bursts (discouraged)' CONFIG_ATM_ENI_BURST_RX_8W bool ' Enable 4W RX bursts (recommended)' CONFIG_ATM_ENI_BURST_RX_4W bool ' Enable 2W RX bursts (optional)' CONFIG_ATM_ENI_BURST_RX_2W fi fi tristate 'Fujitsu FireStream (FS50/FS155) ' CONFIG_ATM_FIRESTREAM tristate 'ZeitNet ZN1221/ZN1225' CONFIG_ATM_ZATM if [ "$CONFIG_ATM_ZATM" != "n" ]; then bool ' Enable extended debugging' CONFIG_ATM_ZATM_DEBUG if [ "$CONFIG_X86" = "y" ]; then bool ' Enable usec resolution timestamps' CONFIG_ATM_ZATM_EXACT_TS fi fi # bool 'Rolfs TI TNETA1570' CONFIG_ATM_TNETA1570 y # if [ "$CONFIG_ATM_TNETA1570" = "y" ]; then # bool ' Enable extended debugging' CONFIG_ATM_TNETA1570_DEBUG n # fi tristate 'IDT 77201 (NICStAR) (ForeRunnerLE)' CONFIG_ATM_NICSTAR if [ "$CONFIG_ATM_NICSTAR" != "n" ]; then bool ' Use suni PHY driver (155Mbps)' CONFIG_ATM_NICSTAR_USE_SUNI bool ' Use IDT77015 PHY driver (25Mbps)' CONFIG_ATM_NICSTAR_USE_IDT77105 fi tristate 'Madge Ambassador (Collage PCI 155 Server)' CONFIG_ATM_AMBASSADOR if [ "$CONFIG_ATM_AMBASSADOR" != "n" ]; then bool ' Enable debugging messages' CONFIG_ATM_AMBASSADOR_DEBUG fi tristate 'Madge Horizon [Ultra] (Collage PCI 25 and Collage PCI 155 Client)' CONFIG_ATM_HORIZON if [ "$CONFIG_ATM_HORIZON" != "n" ]; then bool ' Enable debugging messages' CONFIG_ATM_HORIZON_DEBUG fi tristate 'Interphase ATM PCI x575/x525/x531' CONFIG_ATM_IA if [ "$CONFIG_ATM_IA" != "n" ]; then bool ' Enable debugging messages' CONFIG_ATM_IA_DEBUG fi fi if [ "$CONFIG_PCI" = "y" -o "$CONFIG_SBUS" = "y" ]; then tristate 'FORE Systems 200E-series' CONFIG_ATM_FORE200E_MAYBE if [ "$CONFIG_ATM_FORE200E_MAYBE" != "n" ]; then if [ "$CONFIG_PCI" = "y" ]; then bool ' PCA-200E support' CONFIG_ATM_FORE200E_PCA y if [ "$CONFIG_ATM_FORE200E_PCA" = "y" ]; then bool ' Use default PCA-200E firmware (normally enabled)' CONFIG_ATM_FORE200E_PCA_DEFAULT_FW if [ "$CONFIG_ATM_FORE200E_PCA_DEFAULT_FW" = "n" ]; then string ' Pathname of user-supplied binary firmware' CONFIG_ATM_FORE200E_PCA_FW "" fi fi fi if [ "$CONFIG_SBUS" = "y" ]; then bool ' SBA-200E support' CONFIG_ATM_FORE200E_SBA y if [ "$CONFIG_ATM_FORE200E_SBA" = "y" ]; then bool ' Use default SBA-200E firmware (normally enabled)' CONFIG_ATM_FORE200E_SBA_DEFAULT_FW if [ "$CONFIG_ATM_FORE200E_SBA_DEFAULT_FW" = "n" ]; then string ' Pathname of user-supplied binary firmware' CONFIG_ATM_FORE200E_SBA_FW "" fi fi fi fi if [ "$CONFIG_ATM_FORE200E_PCA" = "y" -o "$CONFIG_ATM_FORE200E_SBA" = "y" ]; \ then int ' Maximum number of tx retries' CONFIG_ATM_FORE200E_TX_RETRY 16 int ' Debugging level (0-3)' CONFIG_ATM_FORE200E_DEBUG 0 if [ "$CONFIG_ATM_FORE200E_MAYBE" = "y" ]; then define_tristate CONFIG_ATM_FORE200E y else define_tristate CONFIG_ATM_FORE200E m fi fi fi endmenu |