/* $Id: lmc_media.c,v 1.16 2000/06/06 08:32:14 asj Exp $ */

#include <linux/version.h>
#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/string.h>
#include <linux/timer.h>
#include <linux/ptrace.h>
#include <linux/errno.h>
#include <linux/ioport.h>
#include <linux/malloc.h>
#include <linux/interrupt.h>
#include <linux/pci.h>
#include <asm/segment.h>
//#include <asm/smp.h>

#if LINUX_VERSION_CODE < 0x20155
#include <linux/bios32.h>
#endif

#include <linux/in.h>
#include <linux/if_arp.h>
#include <asm/processor.h>             /* Processor type for cache alignment. */
#include <asm/bitops.h>
#include <asm/io.h>
#include <asm/dma.h>

#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include "../syncppp.h"
#include <linux/inet.h>

#if LINUX_VERSION_CODE >= 0x20200
#include <asm/uaccess.h>
//#include <asm/spinlock.h>
#endif

#include "lmc_ver.h"
#include "lmc.h"
#include "lmc_var.h"
#include "lmc_ioctl.h"
#include "lmc_debug.h"

#define CONFIG_LMC_IGNORE_HARDWARE_HANDSHAKE 1

 /*
  * Copyright (c) 1997-2000 LAN Media Corporation (LMC)
  * All rights reserved.  www.lanmedia.com
  *
  * This code is written by:
  * Andrew Stanley-Jones (asj@cban.com)
  * Rob Braun (bbraun@vix.com),
  * Michael Graff (explorer@vix.com) and
  * Matt Thomas (matt@3am-software.com).
  *
  * This software may be used and distributed according to the terms
  * of the GNU Public License version 2, incorporated herein by reference.
  */

/*
 * For lack of a better place, put the SSI cable stuff here.
 */
char *lmc_t1_cables[] = {
  "V.10/RS423", "EIA530A", "reserved", "X.21", "V.35",
  "EIA449/EIA530/V.36", "V.28/EIA232", "none", NULL
};

/*
 * protocol independent method.
 */
static void lmc_set_protocol (lmc_softc_t * const, lmc_ctl_t *);

/*
 * media independent methods to check on media status, link, light LEDs,
 * etc.
 */
static void lmc_ds3_init (lmc_softc_t * const);
static void lmc_ds3_default (lmc_softc_t * const);
static void lmc_ds3_set_status (lmc_softc_t * const, lmc_ctl_t *);
static void lmc_ds3_set_100ft (lmc_softc_t * const, int);
static int lmc_ds3_get_link_status (lmc_softc_t * const);
static void lmc_ds3_set_crc_length (lmc_softc_t * const, int);
static void lmc_ds3_set_scram (lmc_softc_t * const, int);
static void lmc_ds3_watchdog (lmc_softc_t * const);

static void lmc_hssi_init (lmc_softc_t * const);
static void lmc_hssi_default (lmc_softc_t * const);
static void lmc_hssi_set_status (lmc_softc_t * const, lmc_ctl_t *);
static void lmc_hssi_set_clock (lmc_softc_t * const, int);
static int lmc_hssi_get_link_status (lmc_softc_t * const);
static void lmc_hssi_set_link_status (lmc_softc_t * const, int);
static void lmc_hssi_set_crc_length (lmc_softc_t * const, int);
static void lmc_hssi_watchdog (lmc_softc_t * const);

static void lmc_ssi_init (lmc_softc_t * const);
static void lmc_ssi_default (lmc_softc_t * const);
static void lmc_ssi_set_status (lmc_softc_t * const, lmc_ctl_t *);
static void lmc_ssi_set_clock (lmc_softc_t * const, int);
static void lmc_ssi_set_speed (lmc_softc_t * const, lmc_ctl_t *);
static int lmc_ssi_get_link_status (lmc_softc_t * const);
static void lmc_ssi_set_link_status (lmc_softc_t * const, int);
static void lmc_ssi_set_crc_length (lmc_softc_t * const, int);
static void lmc_ssi_watchdog (lmc_softc_t * const);

static void lmc_t1_init (lmc_softc_t * const);
static void lmc_t1_default (lmc_softc_t * const);
static void lmc_t1_set_status (lmc_softc_t * const, lmc_ctl_t *);
static int lmc_t1_get_link_status (lmc_softc_t * const);
static void lmc_t1_set_circuit_type (lmc_softc_t * const, int);
static void lmc_t1_set_crc_length (lmc_softc_t * const, int);
static void lmc_t1_set_clock (lmc_softc_t * const, int);
static void lmc_t1_watchdog (lmc_softc_t * const);
static int  lmc_t1_ioctl (lmc_softc_t * const, void *);
static int  lmc_t1_got_interupt (lmc_softc_t * const);

static void lmc_dummy_set_1 (lmc_softc_t * const, int);
static void lmc_dummy_set2_1 (lmc_softc_t * const, lmc_ctl_t *);
static int  lmc_dummy_ioctl (lmc_softc_t * const, void *);
static int  lmc_dummy_got_interupt (lmc_softc_t * const);

static inline void write_av9110_bit (lmc_softc_t *, int);
static void write_av9110 (lmc_softc_t *, u_int32_t, u_int32_t, u_int32_t, /*fold00*/
			  u_int32_t, u_int32_t);

lmc_media_t lmc_ds3_media = {
  lmc_ds3_init,			/* special media init stuff */
  lmc_ds3_default,		/* reset to default state */
  lmc_ds3_set_status,		/* reset status to state provided */
  lmc_dummy_set_1,		/* set clock source */
  lmc_dummy_set2_1,		/* set line speed */
  lmc_ds3_set_100ft,		/* set cable length */
  lmc_ds3_set_scram,		/* set scrambler */
  lmc_ds3_get_link_status,	/* get link status */
  lmc_dummy_set_1,		/* set link status */
  lmc_ds3_set_crc_length,	/* set CRC length */
  lmc_dummy_set_1,		/* set T1 or E1 circuit type */
  lmc_ds3_watchdog,
  lmc_dummy_ioctl,
  lmc_dummy_got_interupt,
};

lmc_media_t lmc_hssi_media = {
  lmc_hssi_init,		/* special media init stuff */
  lmc_hssi_default,		/* reset to default state */
  lmc_hssi_set_status,		/* reset status to state provided */
  lmc_hssi_set_clock,		/* set clock source */
  lmc_dummy_set2_1,		/* set line speed */
  lmc_dummy_set_1,		/* set cable length */
  lmc_dummy_set_1,		/* set scrambler */
  lmc_hssi_get_link_status,	/* get link status */
  lmc_hssi_set_link_status,	/* set link status */
  lmc_hssi_set_crc_length,	/* set CRC length */
  lmc_dummy_set_1,		/* set T1 or E1 circuit type */
  lmc_hssi_watchdog,
  lmc_dummy_ioctl,
  lmc_dummy_got_interupt,

};

lmc_media_t lmc_ssi_media = { lmc_ssi_init,	/* special media init stuff */
  lmc_ssi_default,		/* reset to default state */
  lmc_ssi_set_status,		/* reset status to state provided */
  lmc_ssi_set_clock,		/* set clock source */
  lmc_ssi_set_speed,		/* set line speed */
  lmc_dummy_set_1,		/* set cable length */
  lmc_dummy_set_1,		/* set scrambler */
  lmc_ssi_get_link_status,	/* get link status */
  lmc_ssi_set_link_status,	/* set link status */
  lmc_ssi_set_crc_length,	/* set CRC length */
  lmc_dummy_set_1,		/* set T1 or E1 circuit type */
  lmc_ssi_watchdog,
  lmc_dummy_ioctl,
  lmc_dummy_got_interupt,

};

lmc_media_t lmc_t1_media = {
  lmc_t1_init,			/* special media init stuff */
  lmc_t1_default,		/* reset to default state */
  lmc_t1_set_status,		/* reset status to state provided */
  lmc_t1_set_clock,		/* set clock source */
  lmc_dummy_set2_1,		/* set line speed */
  lmc_dummy_set_1,		/* set cable length */
  lmc_dummy_set_1,		/* set scrambler */
  lmc_t1_get_link_status,	/* get link status */
  lmc_dummy_set_1,		/* set link status */
  lmc_t1_set_crc_length,	/* set CRC length */
  lmc_t1_set_circuit_type,	/* set T1 or E1 circuit type */
  lmc_t1_watchdog,
  lmc_t1_ioctl,
  lmc_t1_got_interupt,

};

static void lmc_dummy_set_1 (lmc_softc_t * const sc, int a) /*fold00*/
{
}

static void lmc_dummy_set2_1 (lmc_softc_t * const sc, lmc_ctl_t * a) /*fold00*/
{
}

static int lmc_dummy_ioctl (lmc_softc_t * const sc, void *d) /*fold00*/
{
    return -ENOSYS;
}

static int lmc_dummy_got_interupt (lmc_softc_t * const sc) /*fold00*/
{
    return -ENOSYS;
}



/*
 *  HSSI methods
 */

static void
lmc_hssi_init (lmc_softc_t * const sc) /*fold00*/
{
  sc->ictl.cardtype = LMC_CTL_CARDTYPE_LMC5200;

  lmc_gpio_mkoutput (sc, LMC_GEP_HSSI_CLOCK);
}

static void
lmc_hssi_default (lmc_softc_t * const sc) /*fold00*/
{
  sc->lmc_miireg16 = LMC_MII16_LED_ALL;

  sc->lmc_media->set_link_status (sc, LMC_LINK_DOWN);
  sc->lmc_media->set_clock_source (sc, LMC_CTL_CLOCK_SOURCE_EXT);
  sc->lmc_media->set_crc_length (sc, LMC_CTL_CRC_LENGTH_16);
}

/*
 * Given a user provided state, set ourselves up to match it.  This will
 * always reset the card if needed.
 */
static void
lmc_hssi_set_status (lmc_softc_t * const sc, lmc_ctl_t * ctl) /*fold00*/
{
  if (ctl == NULL)
    {
      sc->lmc_media->set_clock_source (sc, sc->ictl.clock_source);
      lmc_set_protocol (sc, NULL);

      return;
    }

  /*
   * check for change in clock source
   */
  if (ctl->clock_source && !sc->ictl.clock_source)
    {
      sc->lmc_media->set_clock_source (sc, LMC_CTL_CLOCK_SOURCE_INT);
      sc->lmc_timing = LMC_CTL_CLOCK_SOURCE_INT;
    }
  else if (!ctl->clock_source && sc->ictl.clock_source)
    {
      sc->lmc_timing = LMC_CTL_CLOCK_SOURCE_EXT;
      sc->lmc_media->set_clock_source (sc, LMC_CTL_CLOCK_SOURCE_EXT);
    }

  lmc_set_protocol (sc, ctl);
}

/*
 * 1 == internal, 0 == external
 */
static void
lmc_hssi_set_clock (lmc_softc_t * const sc, int ie) /*fold00*/
{
  int old;
  old = sc->ictl.clock_source;
  if (ie == LMC_CTL_CLOCK_SOURCE_EXT)
    {
      sc->lmc_gpio |= LMC_GEP_HSSI_CLOCK;
      LMC_CSR_WRITE (sc, csr_gp, sc->lmc_gpio);
      sc->ictl.clock_source = LMC_CTL_CLOCK_SOURCE_EXT;
      if(old != ie)
        printk (KERN_INFO "%s: clock external\n", sc->name);
    }
  else
    {
      sc->lmc_gpio &= ~(LMC_GEP_HSSI_CLOCK);
      LMC_CSR_WRITE (sc, csr_gp, sc->lmc_gpio);
      sc->ictl.clock_source = LMC_CTL_CLOCK_SOURCE_INT;
      if(old != ie)
        printk (KERN_INFO "%s: clock internal\n", sc->name);
    }
}

/*
 * return hardware link status.
 * 0 == link is down, 1 == link is up.
 */
static int
lmc_hssi_get_link_status (lmc_softc_t * const sc) /*fold00*/
{
    /*
     * We're using the same code as SSI since
     * they're practically the same
     */
    return lmc_ssi_get_link_status(sc);
}

static void
lmc_hssi_set_link_status (lmc_softc_t * const sc, int state) /*fold00*/
{
  if (state == LMC_LINK_UP)
    sc->lmc_miireg16 |= LMC_MII16_HSSI_TA;
  else
    sc->lmc_miireg16 &= ~LMC_MII16_HSSI_TA;

  lmc_mii_writereg (sc, 0, 16, sc->lmc_miireg16);
}

/*
 * 0 == 16bit, 1 == 32bit
 */
static void
lmc_hssi_set_crc_length (lmc_softc_t * const sc, int state) /*FOLD00*/
{
  if (state == LMC_CTL_CRC_LENGTH_32)
    {
      /* 32 bit */
      sc->lmc_miireg16 |= LMC_MII16_HSSI_CRC;
      sc->ictl.crc_length = LMC_CTL_CRC_LENGTH_32;
      sc->lmc_crcSize = LMC_CTL_CRC_BYTESIZE_4;
    }
  else
    {
      /* 16 bit */
      sc->lmc_miireg16 &= ~LMC_MII16_HSSI_CRC;
      sc->ictl.crc_length = LMC_CTL_CRC_LENGTH_16;
      sc->lmc_crcSize = LMC_CTL_CRC_BYTESIZE_2;
    }

  lmc_mii_writereg (sc, 0, 16, sc->lmc_miireg16);
}

static void
lmc_hssi_watchdog (lmc_softc_t * const sc) /*fold00*/
{
  /* HSSI is blank */
}

/*
 *  DS3 methods
 */

/*
 * Set cable length
 */
static void
lmc_ds3_set_100ft (lmc_softc_t * const sc, int ie) /*fold00*/
{
  if (ie == LMC_CTL_CABLE_LENGTH_GT_100FT)
    {
      sc->lmc_miireg16 &= ~LMC_MII16_DS3_ZERO;
      sc->ictl.cable_length = LMC_CTL_CABLE_LENGTH_GT_100FT;
    }
  else if (ie == LMC_CTL_CABLE_LENGTH_LT_100FT)
    {
      sc->lmc_miireg16 |= LMC_MII16_DS3_ZERO;
      sc->ictl.cable_length = LMC_CTL_CABLE_LENGTH_LT_100FT;
    }
  lmc_mii_writereg (sc, 0, 16, sc->lmc_miireg16);
}

static void
lmc_ds3_default (lmc_softc_t * const sc) /*fold00*/
{
  sc->lmc_miireg16 = LMC_MII16_LED_ALL;

  sc->lmc_media->set_link_status (sc, LMC_LINK_DOWN);
  sc->lmc_media->set_cable_length (sc, LMC_CTL_CABLE_LENGTH_LT_100FT);
  sc->lmc_media->set_scrambler (sc, LMC_CTL_OFF);
  sc->lmc_media->set_crc_length (sc, LMC_CTL_CRC_LENGTH_16);
}

/*
 * Given a user provided state, set ourselves up to match it.  This will
 * always reset the card if needed.
 */
static void
lmc_ds3_set_status (lmc_softc_t * const sc, lmc_ctl_t * ctl) /*fold00*/
{
  if (ctl == NULL)
    {
      sc->lmc_media->set_cable_length (sc, sc->ictl.cable_length);
      sc->lmc_media->set_scrambler (sc, sc->ictl.scrambler_onoff);
      lmc_set_protocol (sc, NULL);

      return;
    }

  /*
   * check for change in cable length setting
   */
  if (ctl->cable_length && !sc->ictl.cable_length)
    lmc_ds3_set_100ft (sc, LMC_CTL_CABLE_LENGTH_GT_100FT);
  else if (!ctl->cable_length && sc->ictl.cable_length)
    lmc_ds3_set_100ft (sc, LMC_CTL_CABLE_LENGTH_LT_100FT);

  /*
   * Check for change in scrambler setting (requires reset)
   */
  if (ctl->scrambler_onoff && !sc->ictl.scrambler_onoff)
    lmc_ds3_set_scram (sc, LMC_CTL_ON);
  else if (!ctl->scrambler_onoff && sc->ictl.scrambler_onoff)
    lmc_ds3_set_scram (sc, LMC_CTL_OFF);

  lmc_set_protocol (sc, ctl);
}

static void
lmc_ds3_init (lmc_softc_t * const sc) /*fold00*/
{
  int i;

  sc->ictl.cardtype = LMC_CTL_CARDTYPE_LMC5245;

  /* writes zeros everywhere */
  for (i = 0; i < 21; i++)
    {
      lmc_mii_writereg (sc, 0, 17, i);
      lmc_mii_writereg (sc, 0, 18, 0);
    }

  /* set some essential bits */
  lmc_mii_writereg (sc, 0, 17, 1);
  lmc_mii_writereg (sc, 0, 18, 0x25);	/* ser, xtx */

  lmc_mii_writereg (sc, 0, 17, 5);
  lmc_mii_writereg (sc, 0, 18, 0x80);	/* emode */

  lmc_mii_writereg (sc, 0, 17, 14);
  lmc_mii_writereg (sc, 0, 18, 0x30);	/* rcgen, tcgen */

  /* clear counters and latched bits */
  for (i = 0; i < 21; i++)
    {
      lmc_mii_writereg (sc, 0, 17, i);
      lmc_mii_readreg (sc, 0, 18);
    }
}

/*
 * 1 == DS3 payload scrambled, 0 == not scrambled
 */
static void
lmc_ds3_set_scram (lmc_softc_t * const sc, int ie) /*fold00*/
{
  if (ie == LMC_CTL_ON)
    {
      sc->lmc_miireg16 |= LMC_MII16_DS3_SCRAM;
      sc->ictl.scrambler_onoff = LMC_CTL_ON;
    }
  else
    {
      sc->lmc_miireg16 &= ~LMC_MII16_DS3_SCRAM;
      sc->ictl.scrambler_onoff = LMC_CTL_OFF;
    }
  lmc_mii_writereg (sc, 0, 16, sc->lmc_miireg16);
}

/*
 * return hardware link status.
 * 0 == link is down, 1 == link is up.
 */
static int
lmc_ds3_get_link_status (lmc_softc_t * const sc) /*fold00*/
{
    u_int16_t link_status, link_status_11;
    int ret = 1;

    lmc_mii_writereg (sc, 0, 17, 7);
    link_status = lmc_mii_readreg (sc, 0, 18);

    /* LMC5245 (DS3) & LMC1200 (DS1) LED definitions
     * led0 yellow = far-end adapter is in Red alarm condition
     * led1 blue   = received an Alarm Indication signal
     *               (upstream failure)
     * led2 Green  = power to adapter, Gate Array loaded & driver
     *               attached
     * led3 red    = Loss of Signal (LOS) or out of frame (OOF)
     *               conditions detected on T3 receive signal
     */

    lmc_led_on(sc, LMC_DS3_LED2);

    if ((link_status & LMC_FRAMER_REG0_DLOS) ||
        (link_status & LMC_FRAMER_REG0_OOFS)){
        ret = 0;
        if(sc->last_led_err[3] != 1){
            u16 r1;
            lmc_mii_writereg (sc, 0, 17, 01); /* Turn on Xbit error as our cisco does */
            r1 = lmc_mii_readreg (sc, 0, 18);
            r1 &= 0xfe;
            lmc_mii_writereg(sc, 0, 18, r1);
            printk(KERN_WARNING "%s: Red Alarm - Loss of Signal or Loss of Framing\n", sc->name);
        }
        lmc_led_on(sc, LMC_DS3_LED3);	/* turn on red LED */
        sc->last_led_err[3] = 1;
    }
    else {
        lmc_led_off(sc, LMC_DS3_LED3);	/* turn on red LED */
        if(sc->last_led_err[3] == 1){
            u16 r1;
            lmc_mii_writereg (sc, 0, 17, 01); /* Turn off Xbit error */
            r1 = lmc_mii_readreg (sc, 0, 18);
            r1 |= 0x01;
            lmc_mii_writereg(sc, 0, 18, r1);
        }
        sc->last_led_err[3] = 0;
    }

    lmc_mii_writereg(sc, 0, 17, 0x10);
    link_status_11 = lmc_mii_readreg(sc, 0, 18);
    if((link_status & LMC_FRAMER_REG0_AIS) ||
       (link_status_11 & LMC_FRAMER_REG10_XBIT)) {
        ret = 0;
        if(sc->last_led_err[0] != 1){
            printk(KERN_WARNING "%s: AIS Alarm or XBit Error\n", sc->name);
            printk(KERN_WARNING "%s: Remote end has loss of signal or framing\n", sc->name);
        }
        lmc_led_on(sc, LMC_DS3_LED0);
        sc->last_led_err[0] = 1;
    }
    else {
        lmc_led_off(sc, LMC_DS3_LED0);
        sc->last_led_err[0] = 0;
    }

    lmc_mii_writereg (sc, 0, 17, 9);
    link_status = lmc_mii_readreg (sc, 0, 18);
    
    if(link_status & LMC_FRAMER_REG9_RBLUE){
        ret = 0;
        if(sc->last_led_err[1] != 1){
            printk(KERN_WARNING "%s: Blue Alarm - Receiving all 1's\n", sc->name);
        }
        lmc_led_on(sc, LMC_DS3_LED1);
        sc->last_led_err[1] = 1;
    }
    else {
        lmc_led_off(sc, LMC_DS3_LED1);
        sc->last_led_err[1] = 0;
    }

    return ret;
}

/*
 * 0 == 16bit, 1 == 32bit
 */
static void
lmc_ds3_set_crc_length (lmc_softc_t * const sc, int state) /*FOLD00*/
{
  if (state == LMC_CTL_CRC_LENGTH_32)
    {
      /* 32 bit */
      sc->lmc_miireg16 |= LMC_MII16_DS3_CRC;
      sc->ictl.crc_length = LMC_CTL_CRC_LENGTH_32;
      sc->lmc_crcSize = LMC_CTL_CRC_BYTESIZE_4;
    }
  else
    {
      /* 16 bit */
      sc->lmc_miireg16 &= ~LMC_MII16_DS3_CRC;
      sc->ictl.crc_length = LMC_CTL_CRC_LENGTH_16;
      sc->lmc_crcSize = LMC_CTL_CRC_BYTESIZE_2;
    }

  lmc_mii_writereg (sc, 0, 16, sc->lmc_miireg16);
}

static void
lmc_ds3_watchdog (lmc_softc_t * const sc) /*fold00*/
{
    
}


/*
 *  SSI methods
 */

static void
lmc_ssi_init (lmc_softc_t * const sc) /*fold00*/
{
  u_int16_t mii17;
  int cable;

  sc->ictl.cardtype = LMC_CTL_CARDTYPE_LMC1000;

  mii17 = lmc_mii_readreg (sc, 0, 17);

  cable = (mii17 & LMC_MII17_SSI_CABLE_MASK) >> LMC_MII17_SSI_CABLE_SHIFT;
  sc->ictl.cable_type = cable;

  lmc_gpio_mkoutput (sc, LMC_GEP_SSI_TXCLOCK);
}

static void
lmc_ssi_default (lmc_softc_t * const sc) /*fold00*/
{
  sc->lmc_miireg16 = LMC_MII16_LED_ALL;

  /*
   * make TXCLOCK always be an output
   */
  lmc_gpio_mkoutput (sc, LMC_GEP_SSI_TXCLOCK);

  sc->lmc_media->set_link_status (sc, LMC_LINK_DOWN);
  sc->lmc_media->set_clock_source (sc, LMC_CTL_CLOCK_SOURCE_EXT);
  sc->lmc_media->set_speed (sc, NULL);
  sc->lmc_media->set_crc_length (sc, LMC_CTL_CRC_LENGTH_16);
}

/*
 * Given a user provided state, set ourselves up to match it.  This will
 * always reset the card if needed.
 */
static void
lmc_ssi_set_status (lmc_softc_t * const sc, lmc_ctl_t * ctl) /*fold00*/
{
  if (ctl == NULL)
    {
      sc->lmc_media->set_clock_source (sc, sc->ictl.clock_source);
      sc->lmc_media->set_speed (sc, &sc->ictl);
      lmc_set_protocol (sc, NULL);

      return;
    }

  /*
   * check for change in clock source
   */
  if (ctl->clock_source == LMC_CTL_CLOCK_SOURCE_INT
      && sc->ictl.clock_source == LMC_CTL_CLOCK_SOURCE_EXT)
    {
      sc->lmc_media->set_clock_source (sc, LMC_CTL_CLOCK_SOURCE_INT);
      sc->lmc_timing = LMC_CTL_CLOCK_SOURCE_INT;
    }
  else if (ctl->clock_source == LMC_CTL_CLOCK_SOURCE_EXT
	   && sc->ictl.clock_source == LMC_CTL_CLOCK_SOURCE_INT)
    {
      sc->lmc_media->set_clock_source (sc, LMC_CTL_CLOCK_SOURCE_EXT);
      sc->lmc_timing = LMC_CTL_CLOCK_SOURCE_EXT;
    }

  if (ctl->clock_rate != sc->ictl.clock_rate)
    sc->lmc_media->set_speed (sc, ctl);

  lmc_set_protocol (sc, ctl);
}

/*
 * 1 == internal, 0 == external
 */
static void
lmc_ssi_set_clock (lmc_softc_t * const sc, int ie) /*fold00*/
{
  int old;
  old = ie;
  if (ie == LMC_CTL_CLOCK_SOURCE_EXT)
    {
      sc->lmc_gpio &= ~(LMC_GEP_SSI_TXCLOCK);
      LMC_CSR_WRITE (sc, csr_gp, sc->lmc_gpio);
      sc->ictl.clock_source = LMC_CTL_CLOCK_SOURCE_EXT;
      if(ie != old)
        printk (KERN_INFO "%s: clock external\n", sc->name);
    }
  else
    {
      sc->lmc_gpio |= LMC_GEP_SSI_TXCLOCK;
      LMC_CSR_WRITE (sc, csr_gp, sc->lmc_gpio);
      sc->ictl.clock_source = LMC_CTL_CLOCK_SOURCE_INT;
      if(ie != old)
        printk (KERN_INFO "%s: clock internal\n", sc->name);
    }
}

static void
lmc_ssi_set_speed (lmc_softc_t * const sc, lmc_ctl_t * ctl) /*fold00*/
{
  lmc_ctl_t *ictl = &sc->ictl;
  lmc_av9110_t *av;

  /* original settings for clock rate of:
   *  100 Khz (8,25,0,0,2) were incorrect
   *  they should have been 80,125,1,3,3
   *  There are 17 param combinations to produce this freq.
   *  For 1.5 Mhz use 120,100,1,1,2 (226 param. combinations)
   */
  if (ctl == NULL)
    {
      av = &ictl->cardspec.ssi;
      ictl->clock_rate = 1500000;
      av->f = ictl->clock_rate;
      av->n = 120;
      av->m = 100;
      av->v = 1;
      av->x = 1;
      av->r = 2;

      write_av9110 (sc, av->n, av->m, av->v, av->x, av->r);
      return;
    }

  av = &ctl->cardspec.ssi;

  if (av->f == 0)
    return;

  ictl->clock_rate = av->f;	/* really, this is the rate we are */
  ictl->cardspec.ssi = *av;

  write_av9110 (sc, av->n, av->m, av->v, av->x, av->r);
}

/*
 * return hardware link status.
 * 0 == link is down, 1 == link is up.
 */
static int
lmc_ssi_get_link_status (lmc_softc_t * const sc) /*fold00*/
{
  u_int16_t link_status;
  u_int32_t ticks;
  int ret = 1;
  int hw_hdsk = 1;
  
  /*
   * missing CTS?  Hmm.  If we require CTS on, we may never get the
   * link to come up, so omit it in this test.
   *
   * Also, it seems that with a loopback cable, DCD isn't asserted,
   * so just check for things like this:
   *      DSR _must_ be asserted.
   *      One of DCD or CTS must be asserted.
   */

  /* LMC 1000 (SSI) LED definitions
   * led0 Green = power to adapter, Gate Array loaded &
   *              driver attached
   * led1 Green = DSR and DTR and RTS and CTS are set
   * led2 Green = Cable detected
   * led3 red   = No timing is available from the
   *              cable or the on-board frequency
   *              generator.
   */

  link_status = lmc_mii_readreg (sc, 0, 16);

  /* Is the transmit clock still available */
  ticks = LMC_CSR_READ (sc, csr_gp_timer);
  ticks = 0x0000ffff - (ticks & 0x0000ffff);

  lmc_led_on (sc, LMC_MII16_LED0);

  /* ====== transmit clock determination ===== */
  if (sc->lmc_timing == LMC_CTL_CLOCK_SOURCE_INT) {
      lmc_led_off(sc, LMC_MII16_LED3);
  }
  else if (ticks == 0 ) {				/* no clock found ? */
      ret = 0;
      if(sc->last_led_err[3] != 1){
          sc->stats.tx_lossOfClockCnt++;
          printk(KERN_WARNING "%s: Lost Clock, Link Down\n", sc->name);
      }
      sc->last_led_err[3] = 1;
      lmc_led_on (sc, LMC_MII16_LED3);	/* turn ON red LED */
  }
  else {
      if(sc->last_led_err[3] == 1)
          printk(KERN_WARNING "%s: Clock Returned\n", sc->name);
      sc->last_led_err[3] = 0;
      lmc_led_off (sc, LMC_MII16_LED3);		/* turn OFF red LED */
  }

  if ((link_status & LMC_MII16_SSI_DSR) == 0) { /* Also HSSI CA */
      ret = 0;
      hw_hdsk = 0;
  }

#ifdef CONFIG_LMC_IGNORE_HARDWARE_HANDSHAKE
  if ((link_status & (LMC_MII16_SSI_CTS | LMC_MII16_SSI_DCD)) == 0){
      ret = 0;
      hw_hdsk = 0;
  }
#endif

  if(hw_hdsk == 0){
      if(sc->last_led_err[1] != 1)
          printk(KERN_WARNING "%s: DSR not asserted\n", sc->name);
      sc->last_led_err[1] = 1;
      lmc_led_off(sc, LMC_MII16_LED1);
  }
  else {
      if(sc->last_led_err[1] != 0)
          printk(KERN_WARNING "%s: DSR now asserted\n", sc->name);
      sc->last_led_err[1] = 0;
      lmc_led_on(sc, LMC_MII16_LED1);
  }

  if(ret == 1) {
      lmc_led_on(sc, LMC_MII16_LED2); /* Over all good status? */
  }
  
  return ret;
}

static void
lmc_ssi_set_link_status (lmc_softc_t * const sc, int state) /*fold00*/
{
  if (state == LMC_LINK_UP)
    {
      sc->lmc_miireg16 |= (LMC_MII16_SSI_DTR | LMC_MII16_SSI_RTS);
//      printk (LMC_PRINTF_FMT ": asserting DTR and RTS\n", LMC_PRINTF_ARGS);
    }
  else
    {
      sc->lmc_miireg16 &= ~(LMC_MII16_SSI_DTR | LMC_MII16_SSI_RTS);
//      printk (LMC_PRINTF_FMT ": deasserting DTR and RTS\n", LMC_PRINTF_ARGS);
    }

  lmc_mii_writereg (sc, 0, 16, sc->lmc_miireg16);

}

/*
 * 0 == 16bit, 1 == 32bit
 */
static void
lmc_ssi_set_crc_length (lmc_softc_t * const sc, int state) /*FOLD00*/
{
  if (state == LMC_CTL_CRC_LENGTH_32)
    {
      /* 32 bit */
      sc->lmc_miireg16 |= LMC_MII16_SSI_CRC;
      sc->ictl.crc_length = LMC_CTL_CRC_LENGTH_32;
      sc->lmc_crcSize = LMC_CTL_CRC_BYTESIZE_4;

    }
  else
    {
      /* 16 bit */
      sc->lmc_miireg16 &= ~LMC_MII16_SSI_CRC;
      sc->ictl.crc_length = LMC_CTL_CRC_LENGTH_16;
      sc->lmc_crcSize = LMC_CTL_CRC_BYTESIZE_2;
    }

  lmc_mii_writereg (sc, 0, 16, sc->lmc_miireg16);
}

/*
 * These are bits to program the ssi frequency generator
 */
static inline void
write_av9110_bit (lmc_softc_t * sc, int c) /*fold00*/
{
  /*
   * set the data bit as we need it.
   */
  sc->lmc_gpio &= ~(LMC_GEP_CLK);
  if (c & 0x01)
    sc->lmc_gpio |= LMC_GEP_DATA;
  else
    sc->lmc_gpio &= ~(LMC_GEP_DATA);
  LMC_CSR_WRITE (sc, csr_gp, sc->lmc_gpio);

  /*
   * set the clock to high
   */
  sc->lmc_gpio |= LMC_GEP_CLK;
  LMC_CSR_WRITE (sc, csr_gp, sc->lmc_gpio);

  /*
   * set the clock to low again.
   */
  sc->lmc_gpio &= ~(LMC_GEP_CLK);
  LMC_CSR_WRITE (sc, csr_gp, sc->lmc_gpio);
}

static void
write_av9110 (lmc_softc_t * sc, u_int32_t n, u_int32_t m, u_int32_t v, /*fold00*/
	      u_int32_t x, u_int32_t r)
{
  int i;

  sc->lmc_gpio |= LMC_GEP_SSI_GENERATOR;
  sc->lmc_gpio &= ~(LMC_GEP_DATA | LMC_GEP_CLK);
  LMC_CSR_WRITE (sc, csr_gp, sc->lmc_gpio);

  /*
   * Set the TXCLOCK, GENERATOR, SERIAL, and SERIALCLK
   * as outputs.
   */
  lmc_gpio_mkoutput (sc, (LMC_GEP_DATA | LMC_GEP_CLK
			  | LMC_GEP_SSI_GENERATOR));

  sc->lmc_gpio &= ~(LMC_GEP_SSI_GENERATOR);
  LMC_CSR_WRITE (sc, csr_gp, sc->lmc_gpio);

  /*
   * a shifting we will go...
   */
  for (i = 0; i < 7; i++)
    write_av9110_bit (sc, n >> i);
  for (i = 0; i < 7; i++)
    write_av9110_bit (sc, m >> i);
  for (i = 0; i < 1; i++)
    write_av9110_bit (sc, v >> i);
  for (i = 0; i < 2; i++)
    write_av9110_bit (sc, x >> i);
  for (i = 0; i < 2; i++)
    write_av9110_bit (sc, r >> i);
  for (i = 0; i < 5; i++)
    write_av9110_bit (sc, 0x17 >> i);

  /*
   * stop driving serial-related signals
   */
  lmc_gpio_mkinput (sc,
		    (LMC_GEP_DATA | LMC_GEP_CLK
		     | LMC_GEP_SSI_GENERATOR));
}

static void
lmc_ssi_watchdog (lmc_softc_t * const sc) /*fold00*/
{
  u_int16_t mii17;
  struct ssicsr2
  {
    unsigned short dtr:1, dsr:1, rts:1, cable:3, crc:1, led0:1, led1:1,
      led2:1, led3:1, fifo:1, ll:1, rl:1, tm:1, loop:1;
  };
  struct ssicsr2 *ssicsr;
  mii17 = lmc_mii_readreg (sc, 0, 17);
  ssicsr = (struct ssicsr2 *) &mii17;
  if (ssicsr->cable == 7)
    {
      lmc_led_off (sc, LMC_MII16_LED2);
    }
  else
    {
      lmc_led_on (sc, LMC_MII16_LED2);
    }

}

/*
 *  T1 methods
 */

/*
 * The framer regs are multiplexed through MII regs 17 & 18
 *  write the register address to MII reg 17 and the *  data to MII reg 18. */
static void
lmc_t1_write (lmc_softc_t * const sc, int a, int d) /*fold00*/
{
  lmc_mii_writereg (sc, 0, 17, a);
  lmc_mii_writereg (sc, 0, 18, d);
}


static int
lmc_t1_read (lmc_softc_t * const sc, int a) /*fold00*/
{
  lmc_mii_writereg (sc, 0, 17, a);
  return lmc_mii_readreg (sc, 0, 18);
}



static void
lmc_t1_init (lmc_softc_t * const sc) /*fold00*/
{
  u_int16_t mii16;
  int i;

  sc->ictl.cardtype = LMC_CTL_CARDTYPE_LMC1200;
  mii16 = lmc_mii_readreg (sc, 0, 16);

  mii16 &= ~LMC_MII16_T1_XOE;
  lmc_mii_writereg (sc, 0, 16, mii16);
  sc->lmc_miireg16 = mii16;

  /* reset 8370 */
  mii16 &= ~LMC_MII16_T1_RST;
  lmc_mii_writereg (sc, 0, 16, mii16 | LMC_MII16_T1_RST);
  lmc_mii_writereg (sc, 0, 16, mii16);

  /* set T1 or E1 line.  Uses sc->lmcmii16 reg in function so update it */
  sc->lmc_miireg16 = mii16;
  lmc_t1_set_circuit_type(sc, LMC_CTL_CIRCUIT_TYPE_T1);
  mii16 = sc->lmc_miireg16;

  /* Clear "foreced alarm" bis */
  sc->yellow_alarm = 0;
  sc->red_alarm = 0;
  sc->blue_alarm = 0;

  /*
   * CR0
   * - Set framing too ESF + Force CRC
   * - Set T1
   */
  
  lmc_t1_write (sc, 0x01, 0x1b);
  /*
   * JAT_CR
   * - set Free Running JCLK and CLAD0
   * - Reset Elastic store to center
   * - 64 bit elastic store
   */
  lmc_t1_write (sc, 0x02, 0x4b);
  
  /*
   * JAT_CR
   * - Release Elastic store reset
   */
  lmc_t1_write (sc, 0x02, 0x43);
  
  /*
   * Disable all interupts
   * Except: BOP receive
   */

  lmc_t1_write (sc, 0x0C, 0x00);
  lmc_t1_write (sc, 0x0D, 0x00);
  lmc_t1_write (sc, 0x0E, 0x00);
  lmc_t1_write (sc, 0x0F, 0x00);
  lmc_t1_write (sc, 0x10, 0x00);
  lmc_t1_write (sc, 0x11, 0x00);
  lmc_t1_write (sc, 0x12, 0x80);
  lmc_t1_write (sc, 0x13, 0x00);
  
  /*
   * LOOP
   * - No loopbacks set
   */
  lmc_t1_write (sc, 0x14, 0x00);
  
  /*
   * DL3_TS
   * - Disabled
   */
  lmc_t1_write (sc, 0x15, 0x00);
  
  /*
   * PIO
   * - ONESEC_IO, RDL_IO, TDL_IO, INDY_IO, RFSYNC_IO, RMSYNC_IO
   *   TFSNYC_IO, TMSYNC_IO: Set for output
   */
  lmc_t1_write (sc, 0x18, 0xFF);	/* PIO     - programmable I/O            */
  
  /*
   * POE
   * TDL_OE, RDL_OE: tri state output capable enable
   * Rest: 2 level output
   */
  lmc_t1_write (sc, 0x19, 0x30);	/* POE     - programmable OE             */
  
  /*
   * CMUX - Clock Input Mux
   * RSBCKLI: Normal RSB timebase
   * TSBCKI: Normal TSB timebase
   * CLADI: CLAD slaved to transmit
   * TCKI: Internal CLAD
   */
  lmc_t1_write (sc, 0x1A, 0x0F);	/* CMUX    - clock input mux             */
  
  /*
   * LIU_CR
   * RST_LIU: Reset LIU
   * SQUELCH: Enable squelch
   * Must be 1: Set to 1
   */
  lmc_t1_write (sc, 0x20, 0xC1);	/* LIU_CR  - RX LIU config               */
  lmc_t1_write (sc, 0x20, 0x41);	/* LIU_CR  - RX LIU config               */
  /*
   * RLIU_CR
   * WHAT IS GOING ON HERE? USED TO BE 0x76
   * FRZ_SHORT: don't update on strong signals
   * AGC: 0x11 normal op
   * LONG_EYE: normal
   */
  lmc_t1_write (sc, 0x22, 0xB1);	/* RLIU_CR - RX LIU config               */

  /*
   * VGA_MAX
   * Setting of -20db sesitivity
   */
  lmc_t1_write (sc, 0x24, 0x21);

  /*
   * PRE_EQ
   * Force off the pre-equilizer
   * Load 0x26 in VTHRESH
   */
  lmc_t1_write (sc, 0x2A, 0xA6);

  /*
   * GAIN
   * Equilizer Gain threshholds
   * Number taken straight from David test code
   */
  lmc_t1_write (sc, 0x38, 0x24);  /* RX_TH0  - RX gain threshold 0         */
  lmc_t1_write (sc, 0x39, 0x28);  /* RX_TH1  - RX gain threshold 0         */
  lmc_t1_write (sc, 0x3A, 0x2C);  /* RX_TH2  - RX gain threshold 0         */
  lmc_t1_write (sc, 0x3B, 0x30);  /* RX_TH3  - RX gain threshold 0         */
  lmc_t1_write (sc, 0x3C, 0x34);  /* RX_TH4  - RX gain threshold 0         */

  /*
   *  LIU_CR
   *  Reset the LIU so it'll load the new constants
   */
  lmc_t1_write (sc, 0x20, 0x81);  /* LIU_CR  - RX LIU config (reset RLIU)  */
  lmc_t1_write (sc, 0x20, 0x01);  /* LIU_CR  - RX LIU config (clear reset) */
  
  /*
   * RCR0
   * Receive B8ZS and 2 out of 4 F-bit errors for reframe
   */
  lmc_t1_write (sc, 0x40, 0x03);	/* RCR0    - RX config                   */

  /*
   * RPATT
   * Zero the test pattern generator
   */
  lmc_t1_write (sc, 0x41, 0x00);

  /*
   * RLB
   * Loop back code detector
   * DN_LEN: Down length is 8 bits
   * UP_LEN: 5 bits
   */
  lmc_t1_write (sc, 0x42, 0x09);

  /*
   * LBA: Loopback activate
   * LBA[6]: 1
   * Loopback activate code
   */
  lmc_t1_write (sc, 0x43, 0x08);

  /*
   * LBD: Loopback deactivate
   *
   * Loopback deactivate code
   */
  lmc_t1_write (sc, 0x44, 0x24);

  /*
   * RALM: Receive Alarm Signal Configuration
   *
   * Set 0 which seems to be narmal alarms
   */
  lmc_t1_write (sc, 0x45, 0x00);

  /*
   * LATCH: Alarm/Error/Cournetr Latch register
   *
   * STOP_CNT: Stop error counters durring RLOF/RLOS/RAIS
   */
  lmc_t1_write (sc, 0x46, 0x08);

  /*
   * TLIU_CR: Transmit LIU Control Register
   *
   * TERM: External Transmit termination
   * LBO: No line buildout
   * Pulse shape from N8370DSE: 3-66
   * // PULSE: 000 = 0 - 133ft 100 ohm twisted pair T1 DSX
   * PULSE: 111 = Long Haul FCC Part 68 100 ohm twisted T1 CSU/NCTE
   */
  
  lmc_t1_write (sc, 0x68, 0x4E);

  /*
   * TCR0: Transmit Framer Configuration
   *
   * TFRAME: 1101 == ESF + Froce CRC
   */
  lmc_t1_write (sc, 0x70, 0x0D);

  /*
   * TCR1: Transmit Configuration Registers
   *
   * TLOFA: 2 out of 4 bit errors = LOF
   * TZCS: 000VB0VB Table 3-20 page 3-72
   */
  lmc_t1_write (sc, 0x71, 0x05);

  /*
   * TFRM: Transmit Frame Format
   *
   * INS_MF: Insert Multiframe aligement
   * INS_CRC: Insert CRC
   * INS_FBIT: Insert Framing
   */
  lmc_t1_write (sc, 0x72, 0x0B);

  /*
   * TERROR
   *
   * Don't xmit any errors
   */
  lmc_t1_write (sc, 0x73, 0x00);

  /*
   * TMAN: Tranimit Mahual Sa-byte/FEBE configuration
   */
  lmc_t1_write (sc, 0x74, 0x00);


  /*
   * TALM: Transmit Alarm Signal Configuration
   *
   * Don't use any of these auto alarms
   */
  lmc_t1_write (sc, 0x75, 0x00);


  /*
   * TPATT: Transmit Pattern Canfiguration
   *
   * No special test patterns
   */
  lmc_t1_write (sc, 0x76, 0x00);

  /*
   * TLB: Transmit Inband Loopback Codhe Configuration
   *
   * Not enabled
   */
  lmc_t1_write (sc, 0x77, 0x00);

  /*
   * CLAD_CR: Clack Rate Adapter Configuration
   *
   * LFGAIN: Loop filter gain 1/2^6
   */
  lmc_t1_write (sc, 0x90, 0x06);	/* CLAD_CR - clock rate adapter config   */

  /*
   * CSEL: CLAD Frequency Select
   *
   * CLADV: 0000 - 1024 kHz
   * CLADO: 0101 - 1544 kHz
   */
  lmc_t1_write (sc, 0x91, 0x05);	/* CSEL    - clad freq sel               */

  /*
   * CPHASE: CLAD Phase detector
   */
  lmc_t1_write (sc, 0x92, 0x00);

  /*
   * CTEST: Clad Test
   *
   * No tests
   */
  lmc_t1_write (sc, 0x93, 0x00);

  /*
   * BOP: Bop receiver
   *
   * Enable, 25 messages receive, 25 send, BOP has priority over FDL
   */
  lmc_t1_write (sc, 0xA0, 0xea);        /* BOP     - Bit oriented protocol xcvr  */

  /*
   * Setup required to activae BOP.
   * See table: 3-22 page 3-87
   * See at the end
   */
  lmc_t1_write (sc, 0xA4, 0x40);        /* DL1_TS  - DL1 time slot enable        */
  lmc_t1_write (sc, 0xA5, 0x00);        /* DL1_BIT - DL1 bit enable              */
  lmc_t1_write (sc, 0xA6, 0x03);        /* DL1_CTL - DL1 control                 */
  lmc_t1_write (sc, 0xA7, 0x00);        /* RDL1_FFC - DL1 FIFO Size */
  lmc_t1_write (sc, 0xAB, 0x00);        /* TDL1_FFC - DL1 Empty Control*/

  /*
   * PRM: FDL PRM Messages
   *
   * Disable all automatic FDL messages
   */
  
  lmc_t1_write (sc, 0xAA, 0x00);        /* PRM     - performance report message  */

  /*
   * DLC2 Control
   *
   * TDL2_EN: Disable transmit
   * RDL2_EN: Disable receive
   */
  lmc_t1_write (sc, 0xB1, 0x00);	/* DL2_CTL - DL2 control                 */
  /*
   * SBI_CR: System Bus Interface Configuration
   *
   * SBI_OE: Enable system bus
   * SBI: T1 at 1544 with 24+fbit Page 3-113
   */
  lmc_t1_write (sc, 0xD0, 0x47);	/* SBI_CR  - sys bus iface config        */
  /*
   * RSB_CR: Receive System Bus Coniguration
   *
   * SIG_OFF: RPCMO signalling off
   * RPCM_NEG: Output on falling edge
   * RSYN_NEG: Output sync an negative edge of clock
   *
   */
  lmc_t1_write (sc, 0xD1, 0x70);

  /*
   * TSB_CR: Transmit System Bus  Configuration
   *
   * TPCM_NEG: Tranimettr multiframe follows TSB
   * TSYN_NEG: TFSYNC or TMSYNC on falling edge output
   */
  lmc_t1_write (sc, 0xD4, 0x30);	/* TSB_CR  - TX sys bus config           */

  for (i = 0; i < 32; i++)
    {
      lmc_t1_write (sc, 0x0E0 + i, 0x00);	/* SBCn - sys bus per-channel ctl    */
      lmc_t1_write (sc, 0x100 + i, 0x00);	/* TPCn - TX per-channel ctl         */
      lmc_t1_write (sc, 0x180 + i, 0x00);	/* RPCn - RX per-channel ctl         */
    }
  for (i=1; i<25; i++)
      lmc_t1_write (sc, 0x0E0 + i, 0x01);       /* SBCn - sys bus per-channel ctl    */
  for (i = 1; i < 25; i++)
    {
      lmc_t1_write (sc, 0x0E0 + i, 0x0D);	/* SBCn - sys bus per-channel ctl    */
    }

  /*
   * Seems to get lost sometimes
   */
  lmc_t1_write (sc, 0xA4, 0x40);        /* DL1_TS  - DL1 time slot enable        */
  lmc_t1_write (sc, 0xA5, 0x00);        /* DL1_BIT - DL1 bit enable              */
  lmc_t1_write (sc, 0xA6, 0x03);        /* DL1_CTL - DL1 control                 */
  lmc_t1_write (sc, 0xA7, 0x00);        /* RDL1_FFC - DL1 FIFO Size */
  lmc_t1_write (sc, 0xAB, 0x00);        /* TDL1_FFC - DL1 Empty Control*/

  /*
   * Basic setup is done, now setup modes like SF AMI, and
   * Fractional T1.
   */

  if(sc->t1_amisf != 0){
      /*
       * Set ami line codeing
       */
      lmc_t1_write (sc, 0x40, 0x83);
      lmc_t1_write (sc, 0x71, 0x07); // 0x03 is ami

      /*
       * Set SF framing
       */
      lmc_t1_write (sc, 0x70, 0x04);
      lmc_t1_write (sc, 0x72, 0x09);
      lmc_t1_write (sc, 0x01, 0x09);

      lmc_t1_write (sc, 0x46,0x00);
      lmc_t1_write (sc, 0xa6,0x00);
      lmc_t1_write (sc, 0xa0,0x00);

      /* Setup Loopback */
      lmc_t1_write (sc, 0x0d, 0xc0);
      lmc_t1_write (sc, 0x42, 0x09);
      lmc_t1_write (sc, 0x43, 0x08);
      lmc_t1_write (sc, 0x44, 0x24);


      if(sc->t1_amisf == 2 && sc->t1_frac_mask == 0){
          sc->t1_frac_mask = 0xfffffffe;
      }
  }

  if(sc->t1_frac_mask){
      u32 mask = sc->t1_frac_mask;
      int i;
      int onoff;
      for(i = 24; i >= 1; i--){
          onoff = mask & 0x1;
          mask >>= 1;
          if(onoff == 0){
              lmc_t1_write(sc, 0x0e0+i,0x01);
              lmc_t1_write(sc, 0x100+i,0x20);
              lmc_t1_write(sc, 0x140+i,0x7f);
          }
          else{
              lmc_t1_write(sc, 0x0e0+i,0x0D);
              lmc_t1_write(sc, 0x100+i,0x00);
              lmc_t1_write(sc, 0x140+i,0x00);
          }
      }
      mii16 |= LMC_MII16_T1_INVERT;
      lmc_mii_writereg (sc, 0, 16, mii16);
  }
  else {
      mii16 &= ~LMC_MII16_T1_INVERT; /* Unless we're on AMI SF don't invert */
  }

  if(sc->t1_loop_time){
	  lmc_t1_write(sc, 0x02, 0xa3);
  }

  lmc_gpio_mkoutput(sc, LMC_GEP_T1_INT);
  sc->lmc_gpio |= LMC_GEP_T1_INT;
  LMC_CSR_WRITE(sc, csr_gp, sc->lmc_gpio);

  mii16 |= LMC_MII16_T1_XOE;
  lmc_mii_writereg (sc, 0, 16, mii16);
  sc->lmc_miireg16 = mii16;
}

static void
lmc_t1_default (lmc_softc_t * const sc) /*fold00*/
{
  sc->lmc_miireg16 = LMC_MII16_LED_ALL;
  sc->lmc_media->set_link_status (sc, LMC_LINK_DOWN);
  sc->lmc_media->set_circuit_type (sc, LMC_CTL_CIRCUIT_TYPE_T1);
  sc->lmc_media->set_crc_length (sc, LMC_CTL_CRC_LENGTH_16);
  /* Right now we can only clock from out internal source */
  sc->ictl.clock_source = LMC_CTL_CLOCK_SOURCE_INT;
}
/* * Given a user provided state, set ourselves up to match it.  This will * always reset the card if needed.
 */
static void
lmc_t1_set_status (lmc_softc_t * const sc, lmc_ctl_t * ctl) /*fold00*/
{
  if (ctl == NULL)
    {
      sc->lmc_media->set_circuit_type (sc, sc->ictl.circuit_type);
      lmc_set_protocol (sc, NULL);

      return;
    }
  /*
   * check for change in circuit type         */
  if (ctl->circuit_type == LMC_CTL_CIRCUIT_TYPE_T1
      && sc->ictl.circuit_type ==
      LMC_CTL_CIRCUIT_TYPE_E1) sc->lmc_media->set_circuit_type (sc,
								LMC_CTL_CIRCUIT_TYPE_E1);
  else if (ctl->circuit_type == LMC_CTL_CIRCUIT_TYPE_E1
	   && sc->ictl.circuit_type == LMC_CTL_CIRCUIT_TYPE_T1)
    sc->lmc_media->set_circuit_type (sc, LMC_CTL_CIRCUIT_TYPE_T1);
  lmc_set_protocol (sc, ctl);
}
/*
 * return hardware link status.
 * 0 == link is down, 1 == link is up.
 */ static int
lmc_t1_get_link_status (lmc_softc_t * const sc) /*fold00*/
{
    u_int16_t link_status;
    int ret = 1;

  /* LMC5245 (DS3) & LMC1200 (DS1) LED definitions
   * led0 yellow = far-end adapter is in Red alarm condition
   * led1 blue   = received an Alarm Indication signal
   *               (upstream failure)
   * led2 Green  = power to adapter, Gate Array loaded & driver
   *               attached
   * led3 red    = Loss of Signal (LOS) or out of frame (OOF)
   *               conditions detected on T3 receive signal
   */
    lmc_trace(sc->lmc_device, "lmc_t1_get_link_status in");
    lmc_led_on(sc, LMC_DS3_LED2);

    lmc_mii_writereg (sc, 0, 17, T1FRAMER_ALARM1_STATUS);
    link_status = lmc_mii_readreg (sc, 0, 18);


    if ((link_status & T1F_RAIS) || sc->blue_alarm) {			/* turn on blue LED */
        ret = 0;
        if(sc->last_led_err[1] != 1){
            printk(KERN_WARNING "%s: Receive AIS/Blue Alarm. Far end in RED alarm\n", sc->name);
        }
        if(sc->blue_alarm != 0){
            sc->blue_alarm--;
        }
        lmc_led_on(sc, LMC_DS3_LED1);
        
        sc->last_led_err[1] = 1;
    }
    else {
        if(sc->last_led_err[1] != 0){
            printk(KERN_WARNING "%s: End AIS/Blue Alarm\n", sc->name);
        }
        lmc_led_off (sc, LMC_DS3_LED1);
        sc->last_led_err[1] = 0;
    }

    /*
     * AMI: Yellow Alarm is nasty evil stuff, looks at data patterns
     * inside the channel and confuses it with HDLC framing
     * ignore all yellow alarms.
     *
     * B8ZS: RAI/Yellow alarm is implemented via a continous BOP
     * message.
     *
     * Do listen to MultiFrame Yellow alarm which while implemented
     * different ways isn't in the channel and hence somewhat
     * more reliable
     */

    if ((link_status & T1F_RMYEL) || sc->yellow_alarm) {
        ret = 0;
        if(sc->last_led_err[0] != 1){
            printk(KERN_WARNING "%s: Receive Yellow AIS Alarm\n", sc->name);
        }
        if(sc->yellow_alarm > 0){
            sc->yellow_alarm--;
        }
        lmc_led_on(sc, LMC_DS3_LED0);
        sc->last_led_err[0] = 1;
    }
    else {
        if(sc->last_led_err[0] != 0){
            printk(KERN_WARNING "%s: End of Yellow AIS Alarm\n", sc->name);
        }
        lmc_led_off(sc, LMC_DS3_LED0);
        sc->last_led_err[0] = 0;
    }

    /*
     * Loss of signal and los of frame
     * Use the green bit to identify which one lit the led
     */
    if((link_status & T1F_RLOF) || sc->red_alarm){
        ret = 0;
        if(sc->last_led_err[3] != 1){
            printk(KERN_WARNING "%s: Local Red Alarm: Loss of Framing (LOF)\n", sc->name);
            /*
             * Send AIS/Yellow
             * So send continuous AIS/Yellom BOP messages
             */
            if(!sc->t1_amisf){
                lmc_t1_write (sc, 0xA0, 0xee); /* Cont BOP */
                lmc_t1_write (sc, 0xA1, 0x00); /* 0x00 is AIS/yellow BOP */
            }
        }
        if(sc->red_alarm != 0){
            sc->red_alarm--;
        }
        lmc_led_on(sc, LMC_DS3_LED3);
        sc->last_led_err[3] = 1;

    }
    else {
        if(sc->last_led_err[3] != 0){
            printk(KERN_WARNING "%s: End Red Alarm (LOF)\n", sc->name);
            /*
             * Stop sending continuous BOP
             * hence end yellow alarm
             */
            if(!sc->t1_amisf){
                lmc_t1_write (sc, 0xA0, 0xea); /* Normal 25 BOP */
            }
        }
        if( ! (link_status & T1F_RLOS))
            lmc_led_off(sc, LMC_DS3_LED3);
        sc->last_led_err[3] = 0;
    }
    
    if((link_status & T1F_RLOS) || sc->red_alarm){
        ret = 0;
        if(sc->last_led_err[2] != 1){
            printk(KERN_WARNING "%s: Local Red Alarm: Loss of Signal (LOS)\n", sc->name);
            /*
             * Send AIS/Yellow
             * So send continuous AIS/Yellom BOP messages
             */
            if(!sc->t1_amisf){
                lmc_t1_write (sc, 0xA0, 0xee); /* Cont BOP */
                lmc_t1_write (sc, 0xA1, 0x00); /* 0x00 is AIS/yellow BOP */
            }
        }
        if(sc->red_alarm != 0){
            sc->red_alarm--;
        }
        lmc_led_on(sc, LMC_DS3_LED3);
        sc->last_led_err[2] = 1;

    }
    else {
        if(sc->last_led_err[2] != 0){
            printk(KERN_WARNING "%s: End Red Alarm (LOS)\n", sc->name);
            /*
             * Stop sending continuous BOP
             * hence end yellow alarm
             */
            if(!sc->t1_amisf){
                lmc_t1_write (sc, 0xA0, 0xea); /* Normal 25 BOP */
            }

        }
        if( ! (link_status & T1F_RLOF))
            lmc_led_off(sc, LMC_DS3_LED3);
        sc->last_led_err[2] = 0;
    }

    sc->lmc_xinfo.t1_alarm1_status = link_status;

    lmc_mii_writereg (sc, 0, 17, T1FRAMER_ALARM2_STATUS);
    sc->lmc_xinfo.t1_alarm2_status = lmc_mii_readreg (sc, 0, 18);

    
    lmc_trace(sc->lmc_device, "lmc_t1_get_link_status out");

    return ret;
}

/*
 * 1 == T1 Circuit Type , 0 == E1 Circuit Type
 */
static void
lmc_t1_set_circuit_type (lmc_softc_t * const sc, int ie) /*fold00*/
{
  int old;
  old = sc->ictl.circuit_type;
  if (ie == LMC_CTL_CIRCUIT_TYPE_T1) {
      sc->ictl.circuit_type = LMC_CTL_CIRCUIT_TYPE_T1;
      if(old != sc->ictl.circuit_type)
          printk(KERN_INFO "%s: In T1 Mode\n", sc->name);
  }
  else {
      sc->ictl.circuit_type = LMC_CTL_CIRCUIT_TYPE_E1;
      if(old != sc->ictl.circuit_type)
          printk(KERN_INFO "%s: In E1 Mode (non functional)\n", sc->name);
  }

  lmc_mii_writereg (sc, 0, 16, sc->lmc_miireg16);
  
}

/*
 * 0 == 16bit, 1 == 32bit */
static void
lmc_t1_set_crc_length (lmc_softc_t * const sc, int state) /*fold00*/
{
  if (state == LMC_CTL_CRC_LENGTH_32)
    {
      /* 32 bit */
      sc->lmc_miireg16 |= LMC_MII16_T1_CRC;
      sc->ictl.crc_length = LMC_CTL_CRC_LENGTH_32;
      sc->lmc_crcSize = LMC_CTL_CRC_BYTESIZE_4;

    }
  else
    {
      /* 16 bit */ sc->lmc_miireg16 &= ~LMC_MII16_T1_CRC;
      sc->ictl.crc_length = LMC_CTL_CRC_LENGTH_16;
      sc->lmc_crcSize = LMC_CTL_CRC_BYTESIZE_2;

    }

  lmc_mii_writereg (sc, 0, 16, sc->lmc_miireg16);
}

/*
 * 1 == internal, 0 == external
 */
static void
lmc_t1_set_clock (lmc_softc_t * const sc, int ie) /*fold00*/
{
    /*
     * Not set this way, done through T1 specific IOCTL
     */
}

static void lmc_t1_watchdog (lmc_softc_t * const sc) /*fold00*/
{
        if(sc->loop_timer != 0){
                sc->loop_timer--;
                if(sc->loop_timer == 0){
                        if(lmc_t1_read(sc, 0x014) != 0x00){
                                printk(KERN_DEBUG "%s: Timeout: Loop down\n", sc->name);
                                lmc_t1_write(sc, 0x014, 0x00);
                                /*
                                 * If we're not loop timed
                                 * go back to intelnal clack
                                 */
                                if(! sc->t1_loop_time){
                                    lmc_t1_write(sc, 0x02, 0x4b);
                                }
                        }
                }
        }
        /*
         * Check for BOP messages on A2 rev boards
         */
        lmc_t1_got_interupt (sc);
}

static int lmc_t1_ioctl (lmc_softc_t * const sc, void *d) /*fold00*/
{
        struct lmc_st1f_control ctl;
        int ret;

        LMC_COPY_FROM_USER(&ctl, d, sizeof (struct lmc_st1f_control));

        switch(ctl.command){
        case lmc_st1f_write:
                lmc_t1_write(sc, ctl.address, ctl.value);
                ret = 0;
                break;
        case lmc_st1f_read:
                ctl.value = lmc_t1_read(sc, ctl.address) & 0xff;
                LMC_COPY_TO_USER(d, &ctl, sizeof (struct lmc_st1f_control));
                ret = 0;
                break;
        case lmc_st1f_inv:
                if(ctl.value == 1){
                  sc->lmc_miireg16 |= LMC_MII16_T1_INVERT;
                  lmc_mii_writereg (sc, 0, 16,   sc->lmc_miireg16);
                  printk("%s: Request to invert data\n", sc->name);
                }
                else {
                  sc->lmc_miireg16 &= ~LMC_MII16_T1_INVERT;
                  lmc_mii_writereg (sc, 0, 16,   sc->lmc_miireg16);
                  printk("%s: Request to non-invert data\n", sc->name);
                }
                ret = 0;
                break;
        case lmc_st1f_amisf:
                sc->t1_amisf = ctl.value;
                if(sc->lmc_ok){
                 lmc_t1_init(sc);
                }
                ret = 0;
                break;
        case lmc_st1f_frac:
                LMC_COPY_FROM_USER(&sc->t1_frac_mask, ctl.data, sizeof (u32));
                if(sc->lmc_ok){
                 lmc_t1_init(sc);
                }
                ret = 0;
                break;
        case lmc_st1f_loopt:
		sc->t1_loop_time = ctl.value;
		if(sc->lmc_ok){
			lmc_t1_init(sc);
		}
		ret = 0;
		break;
        default:
        ret = -ENOSYS;
        }

        return ret;
}

static int lmc_t1_got_interupt (lmc_softc_t * const sc) /*fold00*/
{
        u8 reg;

        /* And it with the mask in case we're polling
         * and we have want the int disabsled
         */
        reg = lmc_t1_read(sc, 0x00a) & lmc_t1_read(sc, 0x12);

        if(reg & 0x80){
//                printk(KERN_DEBUG "%s: Got Inbound BOP message 0x%02x\n", sc->name, lmc_t1_read(sc, 0x0a2) & 0x3f);
                switch(lmc_t1_read(sc, 0x0a2) & 0x3f) {
                case 0x00: /* Yellow Alarm */
                        sc->yellow_alarm = 5; /* Start Yellow Alarm for 3 seconds */
                        break;

                case 0x07: /* Loop up */
                        printk(KERN_DEBUG "%s: BOP: Loop up\n", sc->name);
                        sc->loop_timer = 305;
                        lmc_t1_write(sc, 0x002, 0xa3); /* Enter loop timeing */
                        lmc_t1_write(sc, 0x014, 0x04); /* Loop towards net */
                        break;
                        
                case 0x0b: /* Pay load loop back */
                        printk(KERN_DEBUG "%s: BOP: Payload Loop up\n", sc->name);
                        sc->loop_timer = 305;
                        lmc_t1_write(sc, 0x014, 0x08);
                        break;
                        
                case 0x1a:
                case 0x1c: /* Loop down T1.409, etc */
                case 0x1d: /* Loop down T1.403 */
                        printk(KERN_DEBUG "%s: BOP: Loop down\n", sc->name);
                        lmc_t1_write(sc, 0x014, 0x00); /* Loop down */
                        /*
                         * If we're not loop timed
                         * go back to intelnal clack
                         */
                        if(! sc->t1_loop_time){
                            lmc_t1_write(sc, 0x02, 0x4b);
                        }

                        break;

                }
        }

        reg = lmc_t1_read(sc, 0x005) & lmc_t1_read(sc, 0x0d);
        
        if(reg & 0x04){
            printk(KERN_DEBUG "%s: Inband: Loop up\n", sc->name);
            sc->loop_timer = 305;
            lmc_t1_write(sc, 0x002, 0xa3); /* Enter loop timeing */
            lmc_t1_write(sc, 0x014, 0x04); /* Loop up */
        }
        if(reg & 0x08){
            printk(KERN_DEBUG "%s: Inband: Loop down\n", sc->name);
            lmc_t1_write(sc, 0x014, 0x00);
            /*
             * If we're not loop timed
             * go back to intelnal clack
             */
            if(! sc->t1_loop_time){
                lmc_t1_write(sc, 0x02, 0x4b);
            }
        }
        
        return 0;
}


static void lmc_set_protocol (lmc_softc_t * const sc, lmc_ctl_t * ctl) /*fold00*/
{
  if (ctl == 0)
    {
      sc->ictl.keepalive_onoff = LMC_CTL_ON;

      return;
    }
}