Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129 1130 1131 1132 1133 1134 1135 1136 1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1165 1166 1167 1168 1169 1170 1171 1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210 1211 1212 1213 1214 1215 1216 1217 1218 1219 1220 1221 1222 1223 1224 1225 1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246 1247 1248 1249 1250 1251 1252 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272 1273 1274 1275 1276 1277 1278 1279 1280 1281 1282 1283 1284 1285 1286 1287 1288 1289 1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 1314 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345 1346 1347 1348 1349 1350 1351 1352 1353 1354 1355 1356 1357 1358 1359 1360 1361 1362 1363 1364 1365 1366 1367 1368 1369 1370 1371 1372 1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1385 1386 1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397 1398 1399 1400 1401 1402 1403 1404 1405 1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440 1441 1442 1443 1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456 1457 1458 1459 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492 1493 1494 1495 1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1514 1515 1516 1517 1518 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 1541 1542 1543 1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561 1562 1563 1564 1565 1566 1567 1568 1569 1570 1571 1572 1573 1574 1575 1576 1577 1578 1579 1580 1581 1582 1583 1584 1585 1586 1587 1588 1589 1590 1591 1592 1593 1594 1595 1596 1597 1598 1599 1600 1601 1602 1603 1604 1605 1606 1607 1608 1609 1610 1611 1612 1613 1614 1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625 1626 1627 1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651 1652 1653 1654 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686 1687 1688 1689 1690 1691 1692 1693 1694 1695 1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 1739 1740 1741 1742 1743 1744 1745 1746 1747 1748 1749 1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760 1761 1762 1763 1764 1765 1766 1767 1768 1769 1770 1771 1772 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782 1783 1784 1785 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797 1798 1799 1800 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1820 1821 1822 1823 1824 1825 1826 1827 1828 1829 1830 1831 1832 1833 1834 1835 1836 1837 1838 1839 1840 1841 1842 1843 1844 1845 1846 1847 1848 1849 1850 1851 1852 1853 1854 1855 1856 1857 1858 1859 1860 1861 1862 1863 1864 1865 1866 1867 1868 1869 1870 1871 1872 1873 1874 1875 1876 1877 1878 1879 1880 1881 1882 1883 1884 1885 1886 1887 1888 1889 1890 1891 1892 1893 1894 1895 1896 1897 1898 1899 1900 1901 1902 1903 1904 1905 1906 1907 1908 1909 1910 1911 1912 1913 1914 1915 1916 1917 1918 1919 1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931 1932 1933 1934 1935 1936 1937 1938 1939 1940 1941 1942 1943 1944 1945 1946 1947 1948 1949 1950 1951 1952 1953 1954 1955 1956 1957 1958 1959 1960 1961 1962 1963 1964 1965 1966 1967 1968 1969 1970 1971 1972 1973 1974 1975 1976 1977 1978 1979 1980 1981 1982 1983 1984 1985 1986 1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 2031 2032 2033 2034 2035 2036 2037 2038 2039 2040 2041 2042 2043 2044 2045 2046 2047 2048 2049 2050 2051 2052 2053 2054 2055 2056 2057 2058 2059 2060 2061 2062 2063 2064 2065 2066 2067 2068 2069 2070 2071 2072 2073 2074 2075 2076 2077 2078 2079 2080 2081 2082 2083 2084 2085 2086 2087 2088 2089 2090 2091 2092 2093 2094 2095 2096 2097 2098 2099 2100 2101 2102 2103 2104 2105 2106 2107 2108 2109 2110 2111 2112 2113 2114 2115 2116 2117 2118 2119 2120 2121 2122 2123 2124 2125 2126 2127 2128 2129 2130 2131 2132 2133 2134 2135 2136 2137 2138 2139 2140 2141 2142 2143 2144 2145 2146 2147 2148 2149 2150 2151 2152 2153 2154 2155 2156 2157 2158 2159 2160 2161 2162 2163 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174 2175 2176 2177 2178 2179 2180 2181 2182 2183 2184 2185 2186 2187 2188 2189 2190 2191 2192 2193 2194 2195 2196 2197 2198 2199 2200 2201 2202 2203 2204 2205 2206 2207 2208 2209 2210 2211 2212 2213 2214 2215 2216 2217 2218 2219 2220 2221 2222 2223 2224 2225 2226 2227 2228 2229 2230 2231 2232 2233 2234 2235 2236 2237 2238 2239 2240 2241 2242 2243 2244 2245 2246 2247 2248 2249 2250 2251 2252 2253 2254 2255 2256 2257 2258 2259 2260 2261 2262 2263 2264 2265 2266 2267 2268 2269 2270 2271 2272 2273 2274 2275 2276 2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287 2288 2289 2290 2291 2292 2293 2294 2295 2296 2297 2298 2299 2300 2301 2302 2303 2304 2305 2306 2307 2308 2309 2310 2311 2312 2313 2314 2315 2316 2317 2318 2319 2320 2321 2322 2323 2324 2325 2326 2327 2328 2329 2330 2331 2332 2333 2334 2335 2336 2337 2338 2339 2340 2341 2342 2343 2344 2345 2346 2347 2348 2349 2350 2351 2352 2353 2354 2355 2356 2357 2358 2359 2360 2361 2362 2363 2364 2365 2366 2367 2368 2369 2370 2371 2372 2373 2374 2375 2376 2377 2378 2379 2380 2381 2382 2383 2384 2385 2386 2387 2388 2389 2390 2391 2392 2393 2394 2395 2396 2397 2398 2399 2400 2401 2402 2403 2404 2405 2406 2407 2408 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420 2421 2422 2423 2424 2425 2426 2427 2428 2429 2430 2431 2432 2433 2434 2435 2436 2437 2438 2439 2440 2441 2442 2443 2444 2445 2446 2447 2448 2449 2450 2451 2452 2453 2454 2455 2456 2457 2458 2459 2460 2461 2462 2463 2464 2465 2466 2467 2468 2469 2470 2471 2472 2473 2474 2475 2476 2477 2478 2479 2480 2481 2482 2483 2484 2485 2486 2487 2488 2489 2490 2491 2492 2493 2494 2495 2496 2497 2498 2499 2500 2501 2502 2503 2504 2505 2506 2507 2508 2509 2510 2511 2512 2513 2514 2515 2516 2517 2518 2519 2520 2521 2522 2523 2524 2525 2526 2527 2528 2529 2530 2531 2532 2533 2534 2535 2536 2537 2538 2539 2540 2541 2542 2543 2544 2545 2546 2547 2548 2549 2550 2551 2552 2553 2554 2555 2556 2557 2558 2559 2560 2561 2562 2563 2564 2565 2566 2567 2568 2569 2570 2571 2572 2573 2574 2575 2576 2577 2578 2579 2580 2581 2582 2583 2584 2585 2586 2587 2588 2589 2590 2591 2592 2593 2594 2595 2596 2597 2598 2599 2600 2601 2602 2603 2604 2605 2606 2607 2608 2609 2610 2611 2612 2613 2614 2615 2616 2617 2618 2619 2620 2621 2622 2623 2624 2625 2626 2627 2628 2629 2630 2631 2632 2633 2634 2635 2636 2637 2638 2639 2640 2641 2642 2643 2644 2645 2646 2647 2648 2649 2650 2651 2652 2653 2654 2655 2656 2657 2658 2659 2660 2661 2662 2663 2664 2665 2666 2667 2668 2669 2670 2671 2672 2673 2674 2675 2676 2677 2678 2679 2680 2681 2682 2683 2684 2685 2686 2687 2688 2689 2690 2691 2692 2693 2694 2695 2696 2697 2698 2699 2700 2701 2702 2703 2704 2705 2706 2707 2708 2709 2710 2711 2712 2713 2714 2715 2716 2717 2718 2719 2720 2721 2722 2723 2724 2725 2726 2727 2728 2729 2730 2731 2732 2733 2734 2735 2736 2737 2738 2739 2740 2741 2742 2743 2744 2745 2746 2747 2748 2749 2750 2751 2752 2753 2754 2755 2756 2757 2758 2759 2760 2761 2762 2763 2764 2765 2766 2767 2768 2769 2770 2771 2772 2773 2774 2775 2776 2777 2778 2779 2780 2781 2782 2783 2784 2785 2786 2787 2788 2789 2790 2791 2792 2793 2794 2795 2796 2797 2798 2799 2800 2801 2802 2803 2804 2805 2806 2807 2808 2809 2810 2811 2812 2813 2814 2815 2816 2817 2818 2819 2820 2821 2822 2823 2824 2825 2826 2827 2828 2829 2830 2831 2832 2833 2834 2835 2836 2837 2838 2839 2840 2841 2842 2843 2844 2845 2846 2847 2848 2849 2850 2851 2852 2853 2854 2855 2856 2857 2858 2859 2860 2861 2862 2863 2864 2865 2866 2867 2868 2869 2870 2871 2872 2873 2874 2875 2876 2877 2878 2879 2880 2881 2882 2883 2884 2885 2886 2887 2888 2889 2890 2891 2892 2893 2894 2895 2896 2897 2898 2899 2900 2901 2902 2903 2904 2905 2906 2907 2908 2909 2910 2911 2912 2913 2914 2915 2916 2917 2918 2919 2920 2921 2922 2923 2924 2925 2926 2927 2928 2929 2930 2931 2932 2933 2934 2935 2936 2937 2938 2939 2940 2941 2942 2943 2944 2945 2946 2947 2948 2949 2950 2951 2952 2953 2954 2955 2956 2957 2958 2959 2960 2961 2962 2963 2964 2965 2966 2967 2968 2969 2970 2971 2972 2973 2974 2975 2976 2977 2978 2979 2980 2981 2982 2983 2984 2985 2986 2987 2988 2989 2990 2991 2992 2993 2994 2995 2996 2997 2998 2999 3000 3001 3002 3003 3004 3005 3006 3007 3008 3009 3010 3011 3012 3013 3014 3015 3016 3017 3018 3019 3020 3021 3022 3023 3024 3025 3026 3027 3028 3029 3030 3031 3032 3033 3034 3035 3036 3037 3038 3039 3040 3041 3042 3043 3044 3045 3046 3047 3048 3049 3050 3051 3052 3053 3054 3055 3056 3057 3058 3059 3060 3061 3062 3063 3064 3065 3066 3067 3068 3069 3070 3071 3072 3073 3074 3075 3076 3077 3078 3079 3080 3081 3082 3083 3084 3085 3086 3087 3088 3089 3090 3091 3092 3093 3094 3095 3096 3097 3098 3099 3100 3101 3102 3103 3104 3105 3106 3107 3108 3109 3110 3111 3112 3113 3114 3115 3116 3117 3118 3119 3120 3121 3122 3123 3124 3125 3126 3127 3128 3129 3130 3131 3132 3133 3134 3135 3136 3137 3138 3139 3140 3141 3142 3143 3144 3145 3146 3147 3148 3149 3150 3151 3152 3153 3154 3155 3156 3157 3158 3159 3160 3161 3162 3163 3164 3165 3166 3167 3168 3169 3170 3171 3172 3173 3174 3175 3176 3177 3178 3179 3180 3181 3182 3183 3184 3185 3186 3187 3188 3189 3190 3191 3192 3193 3194 3195 3196 3197 3198 3199 3200 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3213 3214 3215 3216 3217 3218 3219 3220 3221 3222 3223 3224 3225 3226 3227 3228 3229 3230 3231 3232 3233 3234 | .. SPDX-License-Identifier: GPL-2.0 =============== ARCnet Hardware =============== .. note:: 1) This file is a supplement to arcnet.txt. Please read that for general driver configuration help. 2) This file is no longer Linux-specific. It should probably be moved out of the kernel sources. Ideas? Because so many people (myself included) seem to have obtained ARCnet cards without manuals, this file contains a quick introduction to ARCnet hardware, some cabling tips, and a listing of all jumper settings I can find. Please e-mail apenwarr@worldvisions.ca with any settings for your particular card, or any other information you have! Introduction to ARCnet ====================== ARCnet is a network type which works in a way similar to popular Ethernet networks but which is also different in some very important ways. First of all, you can get ARCnet cards in at least two speeds: 2.5 Mbps (slower than Ethernet) and 100 Mbps (faster than normal Ethernet). In fact, there are others as well, but these are less common. The different hardware types, as far as I'm aware, are not compatible and so you cannot wire a 100 Mbps card to a 2.5 Mbps card, and so on. From what I hear, my driver does work with 100 Mbps cards, but I haven't been able to verify this myself, since I only have the 2.5 Mbps variety. It is probably not going to saturate your 100 Mbps card. Stop complaining. :) You also cannot connect an ARCnet card to any kind of Ethernet card and expect it to work. There are two "types" of ARCnet - STAR topology and BUS topology. This refers to how the cards are meant to be wired together. According to most available documentation, you can only connect STAR cards to STAR cards and BUS cards to BUS cards. That makes sense, right? Well, it's not quite true; see below under "Cabling." Once you get past these little stumbling blocks, ARCnet is actually quite a well-designed standard. It uses something called "modified token passing" which makes it completely incompatible with so-called "Token Ring" cards, but which makes transfers much more reliable than Ethernet does. In fact, ARCnet will guarantee that a packet arrives safely at the destination, and even if it can't possibly be delivered properly (ie. because of a cable break, or because the destination computer does not exist) it will at least tell the sender about it. Because of the carefully defined action of the "token", it will always make a pass around the "ring" within a maximum length of time. This makes it useful for realtime networks. In addition, all known ARCnet cards have an (almost) identical programming interface. This means that with one ARCnet driver you can support any card, whereas with Ethernet each manufacturer uses what is sometimes a completely different programming interface, leading to a lot of different, sometimes very similar, Ethernet drivers. Of course, always using the same programming interface also means that when high-performance hardware facilities like PCI bus mastering DMA appear, it's hard to take advantage of them. Let's not go into that. One thing that makes ARCnet cards difficult to program for, however, is the limit on their packet sizes; standard ARCnet can only send packets that are up to 508 bytes in length. This is smaller than the Internet "bare minimum" of 576 bytes, let alone the Ethernet MTU of 1500. To compensate, an extra level of encapsulation is defined by RFC1201, which I call "packet splitting," that allows "virtual packets" to grow as large as 64K each, although they are generally kept down to the Ethernet-style 1500 bytes. For more information on the advantages and disadvantages (mostly the advantages) of ARCnet networks, you might try the "ARCnet Trade Association" WWW page: http://www.arcnet.com Cabling ARCnet Networks ======================= This section was rewritten by Vojtech Pavlik <vojtech@suse.cz> using information from several people, including: - Avery Pennraun <apenwarr@worldvisions.ca> - Stephen A. Wood <saw@hallc1.cebaf.gov> - John Paul Morrison <jmorriso@bogomips.ee.ubc.ca> - Joachim Koenig <jojo@repas.de> and Avery touched it up a bit, at Vojtech's request. ARCnet (the classic 2.5 Mbps version) can be connected by two different types of cabling: coax and twisted pair. The other ARCnet-type networks (100 Mbps TCNS and 320 kbps - 32 Mbps ARCnet Plus) use different types of cabling (Type1, Fiber, C1, C4, C5). For a coax network, you "should" use 93 Ohm RG-62 cable. But other cables also work fine, because ARCnet is a very stable network. I personally use 75 Ohm TV antenna cable. Cards for coax cabling are shipped in two different variants: for BUS and STAR network topologies. They are mostly the same. The only difference lies in the hybrid chip installed. BUS cards use high impedance output, while STAR use low impedance. Low impedance card (STAR) is electrically equal to a high impedance one with a terminator installed. Usually, the ARCnet networks are built up from STAR cards and hubs. There are two types of hubs - active and passive. Passive hubs are small boxes with four BNC connectors containing four 47 Ohm resistors:: | | wires R + junction -R-+-R- R 47 Ohm resistors R | The shielding is connected together. Active hubs are much more complicated; they are powered and contain electronics to amplify the signal and send it to other segments of the net. They usually have eight connectors. Active hubs come in two variants - dumb and smart. The dumb variant just amplifies, but the smart one decodes to digital and encodes back all packets coming through. This is much better if you have several hubs in the net, since many dumb active hubs may worsen the signal quality. And now to the cabling. What you can connect together: 1. A card to a card. This is the simplest way of creating a 2-computer network. 2. A card to a passive hub. Remember that all unused connectors on the hub must be properly terminated with 93 Ohm (or something else if you don't have the right ones) terminators. (Avery's note: oops, I didn't know that. Mine (TV cable) works anyway, though.) 3. A card to an active hub. Here is no need to terminate the unused connectors except some kind of aesthetic feeling. But, there may not be more than eleven active hubs between any two computers. That of course doesn't limit the number of active hubs on the network. 4. An active hub to another. 5. An active hub to passive hub. Remember that you cannot connect two passive hubs together. The power loss implied by such a connection is too high for the net to operate reliably. An example of a typical ARCnet network:: R S - STAR type card S------H--------A-------S R - Terminator | | H - Hub | | A - Active hub | S----H----S S | | S The BUS topology is very similar to the one used by Ethernet. The only difference is in cable and terminators: they should be 93 Ohm. Ethernet uses 50 Ohm impedance. You use T connectors to put the computers on a single line of cable, the bus. You have to put terminators at both ends of the cable. A typical BUS ARCnet network looks like:: RT----T------T------T------T------TR B B B B B B B - BUS type card R - Terminator T - T connector But that is not all! The two types can be connected together. According to the official documentation the only way of connecting them is using an active hub:: A------T------T------TR | B B B S---H---S | S The official docs also state that you can use STAR cards at the ends of BUS network in place of a BUS card and a terminator:: S------T------T------S B B But, according to my own experiments, you can simply hang a BUS type card anywhere in middle of a cable in a STAR topology network. And more - you can use the bus card in place of any star card if you use a terminator. Then you can build very complicated networks fulfilling all your needs! An example:: S | RT------T-------T------H------S B B B | | R S------A------T-------T-------A-------H------TR | B B | | B | S BT | | | | S----A-----S S------H---A----S | | | | S------T----H---S | S S B R S A basically different cabling scheme is used with Twisted Pair cabling. Each of the TP cards has two RJ (phone-cord style) connectors. The cards are then daisy-chained together using a cable connecting every two neighboring cards. The ends are terminated with RJ 93 Ohm terminators which plug into the empty connectors of cards on the ends of the chain. An example:: ___________ ___________ _R_|_ _|_|_ _|_R_ | | | | | | |Card | |Card | |Card | |_____| |_____| |_____| There are also hubs for the TP topology. There is nothing difficult involved in using them; you just connect a TP chain to a hub on any end or even at both. This way you can create almost any network configuration. The maximum of 11 hubs between any two computers on the net applies here as well. An example:: RP-------P--------P--------H-----P------P-----PR | RP-----H--------P--------H-----P------PR | | PR PR R - RJ Terminator P - TP Card H - TP Hub Like any network, ARCnet has a limited cable length. These are the maximum cable lengths between two active ends (an active end being an active hub or a STAR card). ========== ======= =========== RG-62 93 Ohm up to 650 m RG-59/U 75 Ohm up to 457 m RG-11/U 75 Ohm up to 533 m IBM Type 1 150 Ohm up to 200 m IBM Type 3 100 Ohm up to 100 m ========== ======= =========== The maximum length of all cables connected to a passive hub is limited to 65 meters for RG-62 cabling; less for others. You can see that using passive hubs in a large network is a bad idea. The maximum length of a single "BUS Trunk" is about 300 meters for RG-62. The maximum distance between the two most distant points of the net is limited to 3000 meters. The maximum length of a TP cable between two cards/hubs is 650 meters. Setting the Jumpers =================== All ARCnet cards should have a total of four or five different settings: - the I/O address: this is the "port" your ARCnet card is on. Probed values in the Linux ARCnet driver are only from 0x200 through 0x3F0. (If your card has additional ones, which is possible, please tell me.) This should not be the same as any other device on your system. According to a doc I got from Novell, MS Windows prefers values of 0x300 or more, eating net connections on my system (at least) otherwise. My guess is this may be because, if your card is at 0x2E0, probing for a serial port at 0x2E8 will reset the card and probably mess things up royally. - Avery's favourite: 0x300. - the IRQ: on 8-bit cards, it might be 2 (9), 3, 4, 5, or 7. on 16-bit cards, it might be 2 (9), 3, 4, 5, 7, or 10-15. Make sure this is different from any other card on your system. Note that IRQ2 is the same as IRQ9, as far as Linux is concerned. You can "cat /proc/interrupts" for a somewhat complete list of which ones are in use at any given time. Here is a list of common usages from Vojtech Pavlik <vojtech@suse.cz>: ("Not on bus" means there is no way for a card to generate this interrupt) ====== ========================================================= IRQ 0 Timer 0 (Not on bus) IRQ 1 Keyboard (Not on bus) IRQ 2 IRQ Controller 2 (Not on bus, nor does interrupt the CPU) IRQ 3 COM2 IRQ 4 COM1 IRQ 5 FREE (LPT2 if you have it; sometimes COM3; maybe PLIP) IRQ 6 Floppy disk controller IRQ 7 FREE (LPT1 if you don't use the polling driver; PLIP) IRQ 8 Realtime Clock Interrupt (Not on bus) IRQ 9 FREE (VGA vertical sync interrupt if enabled) IRQ 10 FREE IRQ 11 FREE IRQ 12 FREE IRQ 13 Numeric Coprocessor (Not on bus) IRQ 14 Fixed Disk Controller IRQ 15 FREE (Fixed Disk Controller 2 if you have it) ====== ========================================================= .. note:: IRQ 9 is used on some video cards for the "vertical retrace" interrupt. This interrupt would have been handy for things like video games, as it occurs exactly once per screen refresh, but unfortunately IBM cancelled this feature starting with the original VGA and thus many VGA/SVGA cards do not support it. For this reason, no modern software uses this interrupt and it can almost always be safely disabled, if your video card supports it at all. If your card for some reason CANNOT disable this IRQ (usually there is a jumper), one solution would be to clip the printed circuit contact on the board: it's the fourth contact from the left on the back side. I take no responsibility if you try this. - Avery's favourite: IRQ2 (actually IRQ9). Watch that VGA, though. - the memory address: Unlike most cards, ARCnets use "shared memory" for copying buffers around. Make SURE it doesn't conflict with any other used memory in your system! :: A0000 - VGA graphics memory (ok if you don't have VGA) B0000 - Monochrome text mode C0000 \ One of these is your VGA BIOS - usually C0000. E0000 / F0000 - System BIOS Anything less than 0xA0000 is, well, a BAD idea since it isn't above 640k. - Avery's favourite: 0xD0000 - the station address: Every ARCnet card has its own "unique" network address from 0 to 255. Unlike Ethernet, you can set this address yourself with a jumper or switch (or on some cards, with special software). Since it's only 8 bits, you can only have 254 ARCnet cards on a network. DON'T use 0 or 255, since these are reserved (although neat stuff will probably happen if you DO use them). By the way, if you haven't already guessed, don't set this the same as any other ARCnet on your network! - Avery's favourite: 3 and 4. Not that it matters. - There may be ETS1 and ETS2 settings. These may or may not make a difference on your card (many manuals call them "reserved"), but are used to change the delays used when powering up a computer on the network. This is only necessary when wiring VERY long range ARCnet networks, on the order of 4km or so; in any case, the only real requirement here is that all cards on the network with ETS1 and ETS2 jumpers have them in the same position. Chris Hindy <chrish@io.org> sent in a chart with actual values for this: ======= ======= =============== ==================== ET1 ET2 Response Time Reconfiguration Time ======= ======= =============== ==================== open open 74.7us 840us open closed 283.4us 1680us closed open 561.8us 1680us closed closed 1118.6us 1680us ======= ======= =============== ==================== Make sure you set ETS1 and ETS2 to the SAME VALUE for all cards on your network. Also, on many cards (not mine, though) there are red and green LED's. Vojtech Pavlik <vojtech@suse.cz> tells me this is what they mean: =============== =============== ===================================== GREEN RED Status =============== =============== ===================================== OFF OFF Power off OFF Short flashes Cabling problems (broken cable or not terminated) OFF (short) ON Card init ON ON Normal state - everything OK, nothing happens ON Long flashes Data transfer ON OFF Never happens (maybe when wrong ID) =============== =============== ===================================== The following is all the specific information people have sent me about their own particular ARCnet cards. It is officially a mess, and contains huge amounts of duplicated information. I have no time to fix it. If you want to, PLEASE DO! Just send me a 'diff -u' of all your changes. The model # is listed right above specifics for that card, so you should be able to use your text viewer's "search" function to find the entry you want. If you don't KNOW what kind of card you have, try looking through the various diagrams to see if you can tell. If your model isn't listed and/or has different settings, PLEASE PLEASE tell me. I had to figure mine out without the manual, and it WASN'T FUN! Even if your ARCnet model isn't listed, but has the same jumpers as another model that is, please e-mail me to say so. Cards Listed in this file (in this order, mostly): =============== ======================= ==== Manufacturer Model # Bits =============== ======================= ==== SMC PC100 8 SMC PC110 8 SMC PC120 8 SMC PC130 8 SMC PC270E 8 SMC PC500 16 SMC PC500Longboard 16 SMC PC550Longboard 16 SMC PC600 16 SMC PC710 8 SMC? LCS-8830(-T) 8/16 Puredata PDI507 8 CNet Tech CN120-Series 8 CNet Tech CN160-Series 16 Lantech? UM9065L chipset 8 Acer 5210-003 8 Datapoint? LAN-ARC-8 8 Topware TA-ARC/10 8 Thomas-Conrad 500-6242-0097 REV A 8 Waterloo? (C)1985 Waterloo Micro. 8 No Name -- 8/16 No Name Taiwan R.O.C? 8 No Name Model 9058 8 Tiara Tiara Lancard? 8 =============== ======================= ==== * SMC = Standard Microsystems Corp. * CNet Tech = CNet Technology, Inc. Unclassified Stuff ================== - Please send any other information you can find. - And some other stuff (more info is welcome!):: From: root@ultraworld.xs4all.nl (Timo Hilbrink) To: apenwarr@foxnet.net (Avery Pennarun) Date: Wed, 26 Oct 1994 02:10:32 +0000 (GMT) Reply-To: timoh@xs4all.nl [...parts deleted...] About the jumpers: On my PC130 there is one more jumper, located near the cable-connector and it's for changing to star or bus topology; closed: star - open: bus On the PC500 are some more jumper-pins, one block labeled with RX,PDN,TXI and another with ALE,LA17,LA18,LA19 these are undocumented.. [...more parts deleted...] --- CUT --- Standard Microsystems Corp (SMC) ================================ PC100, PC110, PC120, PC130 (8-bit cards) and PC500, PC600 (16-bit cards) ------------------------------------------------------------------------ - mainly from Avery Pennarun <apenwarr@worldvisions.ca>. Values depicted are from Avery's setup. - special thanks to Timo Hilbrink <timoh@xs4all.nl> for noting that PC120, 130, 500, and 600 all have the same switches as Avery's PC100. PC500/600 have several extra, undocumented pins though. (?) - PC110 settings were verified by Stephen A. Wood <saw@cebaf.gov> - Also, the JP- and S-numbers probably don't match your card exactly. Try to find jumpers/switches with the same number of settings - it's probably more reliable. :: JP5 [|] : : : : (IRQ Setting) IRQ2 IRQ3 IRQ4 IRQ5 IRQ7 Put exactly one jumper on exactly one set of pins. 1 2 3 4 5 6 7 8 9 10 S1 /----------------------------------\ (I/O and Memory | 1 1 * 0 0 0 0 * 1 1 0 1 | addresses) \----------------------------------/ |--| |--------| |--------| (a) (b) (m) WARNING. It's very important when setting these which way you're holding the card, and which way you think is '1'! If you suspect that your settings are not being made correctly, try reversing the direction or inverting the switch positions. a: The first digit of the I/O address. Setting Value ------- ----- 00 0 01 1 10 2 11 3 b: The second digit of the I/O address. Setting Value ------- ----- 0000 0 0001 1 0010 2 ... ... 1110 E 1111 F The I/O address is in the form ab0. For example, if a is 0x2 and b is 0xE, the address will be 0x2E0. DO NOT SET THIS LESS THAN 0x200!!!!! m: The first digit of the memory address. Setting Value ------- ----- 0000 0 0001 1 0010 2 ... ... 1110 E 1111 F The memory address is in the form m0000. For example, if m is D, the address will be 0xD0000. DO NOT SET THIS TO C0000, F0000, OR LESS THAN A0000! 1 2 3 4 5 6 7 8 S2 /--------------------------\ (Station Address) | 1 1 0 0 0 0 0 0 | \--------------------------/ Setting Value ------- ----- 00000000 00 10000000 01 01000000 02 ... 01111111 FE 11111111 FF Note that this is binary with the digits reversed! DO NOT SET THIS TO 0 OR 255 (0xFF)! PC130E/PC270E (8-bit cards) --------------------------- - from Juergen Seifert <seifert@htwm.de> This description has been written by Juergen Seifert <seifert@htwm.de> using information from the following Original SMC Manual "Configuration Guide for ARCNET(R)-PC130E/PC270 Network Controller Boards Pub. # 900.044A June, 1989" ARCNET is a registered trademark of the Datapoint Corporation SMC is a registered trademark of the Standard Microsystems Corporation The PC130E is an enhanced version of the PC130 board, is equipped with a standard BNC female connector for connection to RG-62/U coax cable. Since this board is designed both for point-to-point connection in star networks and for connection to bus networks, it is downwardly compatible with all the other standard boards designed for coax networks (that is, the PC120, PC110 and PC100 star topology boards and the PC220, PC210 and PC200 bus topology boards). The PC270E is an enhanced version of the PC260 board, is equipped with two modular RJ11-type jacks for connection to twisted pair wiring. It can be used in a star or a daisy-chained network. :: 8 7 6 5 4 3 2 1 ________________________________________________________________ | | S1 | | | |_________________| | | Offs|Base |I/O Addr | | RAM Addr | ___| | ___ ___ CR3 |___| | | \/ | CR4 |___| | | PROM | ___| | | | N | | 8 | | SOCKET | o | | 7 | |________| d | | 6 | ___________________ e | | 5 | | | A | S | 4 | |oo| EXT2 | | d | 2 | 3 | |oo| EXT1 | SMC | d | | 2 | |oo| ROM | 90C63 | r |___| 1 | |oo| IRQ7 | | |o| _____| | |oo| IRQ5 | | |o| | J1 | | |oo| IRQ4 | | STAR |_____| | |oo| IRQ3 | | | J2 | | |oo| IRQ2 |___________________| |_____| |___ ______________| | | |_____________________________________________| Legend:: SMC 90C63 ARCNET Controller / Transceiver /Logic S1 1-3: I/O Base Address Select 4-6: Memory Base Address Select 7-8: RAM Offset Select S2 1-8: Node ID Select EXT Extended Timeout Select ROM ROM Enable Select STAR Selected - Star Topology (PC130E only) Deselected - Bus Topology (PC130E only) CR3/CR4 Diagnostic LEDs J1 BNC RG62/U Connector (PC130E only) J1 6-position Telephone Jack (PC270E only) J2 6-position Telephone Jack (PC270E only) Setting one of the switches to Off/Open means "1", On/Closed means "0". Setting the Node ID ^^^^^^^^^^^^^^^^^^^ The eight switches in group S2 are used to set the node ID. These switches work in a way similar to the PC100-series cards; see that entry for more information. Setting the I/O Base Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The first three switches in switch group S1 are used to select one of eight possible I/O Base addresses using the following table:: Switch | Hex I/O 1 2 3 | Address -------|-------- 0 0 0 | 260 0 0 1 | 290 0 1 0 | 2E0 (Manufacturer's default) 0 1 1 | 2F0 1 0 0 | 300 1 0 1 | 350 1 1 0 | 380 1 1 1 | 3E0 Setting the Base Memory (RAM) buffer Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The memory buffer requires 2K of a 16K block of RAM. The base of this 16K block can be located in any of eight positions. Switches 4-6 of switch group S1 select the Base of the 16K block. Within that 16K address space, the buffer may be assigned any one of four positions, determined by the offset, switches 7 and 8 of group S1. :: Switch | Hex RAM | Hex ROM 4 5 6 7 8 | Address | Address *) -----------|---------|----------- 0 0 0 0 0 | C0000 | C2000 0 0 0 0 1 | C0800 | C2000 0 0 0 1 0 | C1000 | C2000 0 0 0 1 1 | C1800 | C2000 | | 0 0 1 0 0 | C4000 | C6000 0 0 1 0 1 | C4800 | C6000 0 0 1 1 0 | C5000 | C6000 0 0 1 1 1 | C5800 | C6000 | | 0 1 0 0 0 | CC000 | CE000 0 1 0 0 1 | CC800 | CE000 0 1 0 1 0 | CD000 | CE000 0 1 0 1 1 | CD800 | CE000 | | 0 1 1 0 0 | D0000 | D2000 (Manufacturer's default) 0 1 1 0 1 | D0800 | D2000 0 1 1 1 0 | D1000 | D2000 0 1 1 1 1 | D1800 | D2000 | | 1 0 0 0 0 | D4000 | D6000 1 0 0 0 1 | D4800 | D6000 1 0 0 1 0 | D5000 | D6000 1 0 0 1 1 | D5800 | D6000 | | 1 0 1 0 0 | D8000 | DA000 1 0 1 0 1 | D8800 | DA000 1 0 1 1 0 | D9000 | DA000 1 0 1 1 1 | D9800 | DA000 | | 1 1 0 0 0 | DC000 | DE000 1 1 0 0 1 | DC800 | DE000 1 1 0 1 0 | DD000 | DE000 1 1 0 1 1 | DD800 | DE000 | | 1 1 1 0 0 | E0000 | E2000 1 1 1 0 1 | E0800 | E2000 1 1 1 1 0 | E1000 | E2000 1 1 1 1 1 | E1800 | E2000 *) To enable the 8K Boot PROM install the jumper ROM. The default is jumper ROM not installed. Setting the Timeouts and Interrupt ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The jumpers labeled EXT1 and EXT2 are used to determine the timeout parameters. These two jumpers are normally left open. To select a hardware interrupt level set one (only one!) of the jumpers IRQ2, IRQ3, IRQ4, IRQ5, IRQ7. The Manufacturer's default is IRQ2. Configuring the PC130E for Star or Bus Topology ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The single jumper labeled STAR is used to configure the PC130E board for star or bus topology. When the jumper is installed, the board may be used in a star network, when it is removed, the board can be used in a bus topology. Diagnostic LEDs ^^^^^^^^^^^^^^^ Two diagnostic LEDs are visible on the rear bracket of the board. The green LED monitors the network activity: the red one shows the board activity:: Green | Status Red | Status -------|------------------- ---------|------------------- on | normal activity flash/on | data transfer blink | reconfiguration off | no data transfer; off | defective board or | incorrect memory or | node ID is zero | I/O address PC500/PC550 Longboard (16-bit cards) ------------------------------------ - from Juergen Seifert <seifert@htwm.de> .. note:: There is another Version of the PC500 called Short Version, which is different in hard- and software! The most important differences are: - The long board has no Shared memory. - On the long board the selection of the interrupt is done by binary coded switch, on the short board directly by jumper. [Avery's note: pay special attention to that: the long board HAS NO SHARED MEMORY. This means the current Linux-ARCnet driver can't use these cards. I have obtained a PC500Longboard and will be doing some experiments on it in the future, but don't hold your breath. Thanks again to Juergen Seifert for his advice about this!] This description has been written by Juergen Seifert <seifert@htwm.de> using information from the following Original SMC Manual "Configuration Guide for SMC ARCNET-PC500/PC550 Series Network Controller Boards Pub. # 900.033 Rev. A November, 1989" ARCNET is a registered trademark of the Datapoint Corporation SMC is a registered trademark of the Standard Microsystems Corporation The PC500 is equipped with a standard BNC female connector for connection to RG-62/U coax cable. The board is designed both for point-to-point connection in star networks and for connection to bus networks. The PC550 is equipped with two modular RJ11-type jacks for connection to twisted pair wiring. It can be used in a star or a daisy-chained (BUS) network. :: 1 0 9 8 7 6 5 4 3 2 1 6 5 4 3 2 1 ____________________________________________________________________ < | SW1 | | SW2 | | > |_____________________| |_____________| | < IRQ |I/O Addr | > ___| < CR4 |___| > CR3 |___| < ___| > N | | 8 < o | | 7 > d | S | 6 < e | W | 5 > A | 3 | 4 < d | | 3 > d | | 2 < r |___| 1 > |o| _____| < |o| | J1 | > 3 1 JP6 |_____| < |o|o| JP2 | J2 | > |o|o| |_____| < 4 2__ ______________| > | | | <____| |_____________________________________________| Legend:: SW1 1-6: I/O Base Address Select 7-10: Interrupt Select SW2 1-6: Reserved for Future Use SW3 1-8: Node ID Select JP2 1-4: Extended Timeout Select JP6 Selected - Star Topology (PC500 only) Deselected - Bus Topology (PC500 only) CR3 Green Monitors Network Activity CR4 Red Monitors Board Activity J1 BNC RG62/U Connector (PC500 only) J1 6-position Telephone Jack (PC550 only) J2 6-position Telephone Jack (PC550 only) Setting one of the switches to Off/Open means "1", On/Closed means "0". Setting the Node ID ^^^^^^^^^^^^^^^^^^^ The eight switches in group SW3 are used to set the node ID. Each node attached to the network must have an unique node ID which must be different from 0. Switch 1 serves as the least significant bit (LSB). The node ID is the sum of the values of all switches set to "1" These values are:: Switch | Value -------|------- 1 | 1 2 | 2 3 | 4 4 | 8 5 | 16 6 | 32 7 | 64 8 | 128 Some Examples:: Switch | Hex | Decimal 8 7 6 5 4 3 2 1 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed 0 0 0 0 0 0 0 1 | 1 | 1 0 0 0 0 0 0 1 0 | 2 | 2 0 0 0 0 0 0 1 1 | 3 | 3 . . . | | 0 1 0 1 0 1 0 1 | 55 | 85 . . . | | 1 0 1 0 1 0 1 0 | AA | 170 . . . | | 1 1 1 1 1 1 0 1 | FD | 253 1 1 1 1 1 1 1 0 | FE | 254 1 1 1 1 1 1 1 1 | FF | 255 Setting the I/O Base Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The first six switches in switch group SW1 are used to select one of 32 possible I/O Base addresses using the following table:: Switch | Hex I/O 6 5 4 3 2 1 | Address -------------|-------- 0 1 0 0 0 0 | 200 0 1 0 0 0 1 | 210 0 1 0 0 1 0 | 220 0 1 0 0 1 1 | 230 0 1 0 1 0 0 | 240 0 1 0 1 0 1 | 250 0 1 0 1 1 0 | 260 0 1 0 1 1 1 | 270 0 1 1 0 0 0 | 280 0 1 1 0 0 1 | 290 0 1 1 0 1 0 | 2A0 0 1 1 0 1 1 | 2B0 0 1 1 1 0 0 | 2C0 0 1 1 1 0 1 | 2D0 0 1 1 1 1 0 | 2E0 (Manufacturer's default) 0 1 1 1 1 1 | 2F0 1 1 0 0 0 0 | 300 1 1 0 0 0 1 | 310 1 1 0 0 1 0 | 320 1 1 0 0 1 1 | 330 1 1 0 1 0 0 | 340 1 1 0 1 0 1 | 350 1 1 0 1 1 0 | 360 1 1 0 1 1 1 | 370 1 1 1 0 0 0 | 380 1 1 1 0 0 1 | 390 1 1 1 0 1 0 | 3A0 1 1 1 0 1 1 | 3B0 1 1 1 1 0 0 | 3C0 1 1 1 1 0 1 | 3D0 1 1 1 1 1 0 | 3E0 1 1 1 1 1 1 | 3F0 Setting the Interrupt ^^^^^^^^^^^^^^^^^^^^^ Switches seven through ten of switch group SW1 are used to select the interrupt level. The interrupt level is binary coded, so selections from 0 to 15 would be possible, but only the following eight values will be supported: 3, 4, 5, 7, 9, 10, 11, 12. :: Switch | IRQ 10 9 8 7 | ---------|-------- 0 0 1 1 | 3 0 1 0 0 | 4 0 1 0 1 | 5 0 1 1 1 | 7 1 0 0 1 | 9 (=2) (default) 1 0 1 0 | 10 1 0 1 1 | 11 1 1 0 0 | 12 Setting the Timeouts ^^^^^^^^^^^^^^^^^^^^ The two jumpers JP2 (1-4) are used to determine the timeout parameters. These two jumpers are normally left open. Refer to the COM9026 Data Sheet for alternate configurations. Configuring the PC500 for Star or Bus Topology ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The single jumper labeled JP6 is used to configure the PC500 board for star or bus topology. When the jumper is installed, the board may be used in a star network, when it is removed, the board can be used in a bus topology. Diagnostic LEDs ^^^^^^^^^^^^^^^ Two diagnostic LEDs are visible on the rear bracket of the board. The green LED monitors the network activity: the red one shows the board activity:: Green | Status Red | Status -------|------------------- ---------|------------------- on | normal activity flash/on | data transfer blink | reconfiguration off | no data transfer; off | defective board or | incorrect memory or | node ID is zero | I/O address PC710 (8-bit card) ------------------ - from J.S. van Oosten <jvoosten@compiler.tdcnet.nl> Note: this data is gathered by experimenting and looking at info of other cards. However, I'm sure I got 99% of the settings right. The SMC710 card resembles the PC270 card, but is much more basic (i.e. no LEDs, RJ11 jacks, etc.) and 8 bit. Here's a little drawing:: _______________________________________ | +---------+ +---------+ |____ | | S2 | | S1 | | | +---------+ +---------+ | | | | +===+ __ | | | R | | | X-tal ###___ | | O | |__| ####__'| | | M | || ### | +===+ | | | | .. JP1 +----------+ | | .. | big chip | | | .. | 90C63 | | | .. | | | | .. +----------+ | ------- ----------- ||||||||||||||||||||| The row of jumpers at JP1 actually consists of 8 jumpers, (sometimes labelled) the same as on the PC270, from top to bottom: EXT2, EXT1, ROM, IRQ7, IRQ5, IRQ4, IRQ3, IRQ2 (gee, wonder what they would do? :-) ) S1 and S2 perform the same function as on the PC270, only their numbers are swapped (S1 is the nodeaddress, S2 sets IO- and RAM-address). I know it works when connected to a PC110 type ARCnet board. ***************************************************************************** Possibly SMC ============ LCS-8830(-T) (8 and 16-bit cards) --------------------------------- - from Mathias Katzer <mkatzer@HRZ.Uni-Bielefeld.DE> - Marek Michalkiewicz <marekm@i17linuxb.ists.pwr.wroc.pl> says the LCS-8830 is slightly different from LCS-8830-T. These are 8 bit, BUS only (the JP0 jumper is hardwired), and BNC only. This is a LCS-8830-T made by SMC, I think ('SMC' only appears on one PLCC, nowhere else, not even on the few Xeroxed sheets from the manual). SMC ARCnet Board Type LCS-8830-T:: ------------------------------------ | | | JP3 88 8 JP2 | | ##### | \ | | ##### ET1 ET2 ###| | 8 ###| | U3 SW 1 JP0 ###| Phone Jacks | -- ###| | | | | | | | SW2 | | | | | | | | ##### | | -- ##### #### BNC Connector | #### | 888888 JP1 | | 234567 | -- ------- ||||||||||||||||||||||||||| -------------------------- SW1: DIP-Switches for Station Address SW2: DIP-Switches for Memory Base and I/O Base addresses JP0: If closed, internal termination on (default open) JP1: IRQ Jumpers JP2: Boot-ROM enabled if closed JP3: Jumpers for response timeout U3: Boot-ROM Socket ET1 ET2 Response Time Idle Time Reconfiguration Time 78 86 840 X 285 316 1680 X 563 624 1680 X X 1130 1237 1680 (X means closed jumper) (DIP-Switch downwards means "0") The station address is binary-coded with SW1. The I/O base address is coded with DIP-Switches 6,7 and 8 of SW2: ======== ======== Switches Base 678 Address ======== ======== 000 260-26f 100 290-29f 010 2e0-2ef 110 2f0-2ff 001 300-30f 101 350-35f 011 380-38f 111 3e0-3ef ======== ======== DIP Switches 1-5 of SW2 encode the RAM and ROM Address Range: ======== ============= ================ Switches RAM ROM 12345 Address Range Address Range ======== ============= ================ 00000 C:0000-C:07ff C:2000-C:3fff 10000 C:0800-C:0fff 01000 C:1000-C:17ff 11000 C:1800-C:1fff 00100 C:4000-C:47ff C:6000-C:7fff 10100 C:4800-C:4fff 01100 C:5000-C:57ff 11100 C:5800-C:5fff 00010 C:C000-C:C7ff C:E000-C:ffff 10010 C:C800-C:Cfff 01010 C:D000-C:D7ff 11010 C:D800-C:Dfff 00110 D:0000-D:07ff D:2000-D:3fff 10110 D:0800-D:0fff 01110 D:1000-D:17ff 11110 D:1800-D:1fff 00001 D:4000-D:47ff D:6000-D:7fff 10001 D:4800-D:4fff 01001 D:5000-D:57ff 11001 D:5800-D:5fff 00101 D:8000-D:87ff D:A000-D:bfff 10101 D:8800-D:8fff 01101 D:9000-D:97ff 11101 D:9800-D:9fff 00011 D:C000-D:c7ff D:E000-D:ffff 10011 D:C800-D:cfff 01011 D:D000-D:d7ff 11011 D:D800-D:dfff 00111 E:0000-E:07ff E:2000-E:3fff 10111 E:0800-E:0fff 01111 E:1000-E:17ff 11111 E:1800-E:1fff ======== ============= ================ PureData Corp ============= PDI507 (8-bit card) -------------------- - from Mark Rejhon <mdrejhon@magi.com> (slight modifications by Avery) - Avery's note: I think PDI508 cards (but definitely NOT PDI508Plus cards) are mostly the same as this. PDI508Plus cards appear to be mainly software-configured. Jumpers: There is a jumper array at the bottom of the card, near the edge connector. This array is labelled J1. They control the IRQs and something else. Put only one jumper on the IRQ pins. ETS1, ETS2 are for timing on very long distance networks. See the more general information near the top of this file. There is a J2 jumper on two pins. A jumper should be put on them, since it was already there when I got the card. I don't know what this jumper is for though. There is a two-jumper array for J3. I don't know what it is for, but there were already two jumpers on it when I got the card. It's a six pin grid in a two-by-three fashion. The jumpers were configured as follows:: .-------. o | o o | :-------: ------> Accessible end of card with connectors o | o o | in this direction -------> `-------' Carl de Billy <CARL@carainfo.com> explains J3 and J4: J3 Diagram:: .-------. o | o o | :-------: TWIST Technology o | o o | `-------' .-------. | o o | o :-------: COAX Technology | o o | o `-------' - If using coax cable in a bus topology the J4 jumper must be removed; place it on one pin. - If using bus topology with twisted pair wiring move the J3 jumpers so they connect the middle pin and the pins closest to the RJ11 Connectors. Also the J4 jumper must be removed; place it on one pin of J4 jumper for storage. - If using star topology with twisted pair wiring move the J3 jumpers so they connect the middle pin and the pins closest to the RJ11 connectors. DIP Switches: The DIP switches accessible on the accessible end of the card while it is installed, is used to set the ARCnet address. There are 8 switches. Use an address from 1 to 254 ========== ========================= Switch No. ARCnet address 12345678 ========== ========================= 00000000 FF (Don't use this!) 00000001 FE 00000010 FD ... 11111101 2 11111110 1 11111111 0 (Don't use this!) ========== ========================= There is another array of eight DIP switches at the top of the card. There are five labelled MS0-MS4 which seem to control the memory address, and another three labelled IO0-IO2 which seem to control the base I/O address of the card. This was difficult to test by trial and error, and the I/O addresses are in a weird order. This was tested by setting the DIP switches, rebooting the computer, and attempting to load ARCETHER at various addresses (mostly between 0x200 and 0x400). The address that caused the red transmit LED to blink, is the one that I thought works. Also, the address 0x3D0 seem to have a special meaning, since the ARCETHER packet driver loaded fine, but without the red LED blinking. I don't know what 0x3D0 is for though. I recommend using an address of 0x300 since Windows may not like addresses below 0x300. ============= =========== IO Switch No. I/O address 210 ============= =========== 111 0x260 110 0x290 101 0x2E0 100 0x2F0 011 0x300 010 0x350 001 0x380 000 0x3E0 ============= =========== The memory switches set a reserved address space of 0x1000 bytes (0x100 segment units, or 4k). For example if I set an address of 0xD000, it will use up addresses 0xD000 to 0xD100. The memory switches were tested by booting using QEMM386 stealth, and using LOADHI to see what address automatically became excluded from the upper memory regions, and then attempting to load ARCETHER using these addresses. I recommend using an ARCnet memory address of 0xD000, and putting the EMS page frame at 0xC000 while using QEMM stealth mode. That way, you get contiguous high memory from 0xD100 almost all the way the end of the megabyte. Memory Switch 0 (MS0) didn't seem to work properly when set to OFF on my card. It could be malfunctioning on my card. Experiment with it ON first, and if it doesn't work, set it to OFF. (It may be a modifier for the 0x200 bit?) ============= ============================================ MS Switch No. 43210 Memory address ============= ============================================ 00001 0xE100 (guessed - was not detected by QEMM) 00011 0xE000 (guessed - was not detected by QEMM) 00101 0xDD00 00111 0xDC00 01001 0xD900 01011 0xD800 01101 0xD500 01111 0xD400 10001 0xD100 10011 0xD000 10101 0xCD00 10111 0xCC00 11001 0xC900 (guessed - crashes tested system) 11011 0xC800 (guessed - crashes tested system) 11101 0xC500 (guessed - crashes tested system) 11111 0xC400 (guessed - crashes tested system) ============= ============================================ CNet Technology Inc. (8-bit cards) ================================== 120 Series (8-bit cards) ------------------------ - from Juergen Seifert <seifert@htwm.de> This description has been written by Juergen Seifert <seifert@htwm.de> using information from the following Original CNet Manual "ARCNET USER'S MANUAL for CN120A CN120AB CN120TP CN120ST CN120SBT P/N:12-01-0007 Revision 3.00" ARCNET is a registered trademark of the Datapoint Corporation - P/N 120A ARCNET 8 bit XT/AT Star - P/N 120AB ARCNET 8 bit XT/AT Bus - P/N 120TP ARCNET 8 bit XT/AT Twisted Pair - P/N 120ST ARCNET 8 bit XT/AT Star, Twisted Pair - P/N 120SBT ARCNET 8 bit XT/AT Star, Bus, Twisted Pair :: __________________________________________________________________ | | | ___| | LED |___| | ___| | N | | ID7 | o | | ID6 | d | S | ID5 | e | W | ID4 | ___________________ A | 2 | ID3 | | | d | | ID2 | | | 1 2 3 4 5 6 7 8 d | | ID1 | | | _________________ r |___| ID0 | | 90C65 || SW1 | ____| | JP 8 7 | ||_________________| | | | |o|o| JP1 | | | J2 | | |o|o| |oo| | | JP 1 1 1 | | | ______________ | | 0 1 2 |____| | | PROM | |___________________| |o|o|o| _____| | > SOCKET | JP 6 5 4 3 2 |o|o|o| | J1 | | |______________| |o|o|o|o|o| |o|o|o| |_____| |_____ |o|o|o|o|o| ______________| | | |_____________________________________________| Legend:: 90C65 ARCNET Probe S1 1-5: Base Memory Address Select 6-8: Base I/O Address Select S2 1-8: Node ID Select (ID0-ID7) JP1 ROM Enable Select JP2 IRQ2 JP3 IRQ3 JP4 IRQ4 JP5 IRQ5 JP6 IRQ7 JP7/JP8 ET1, ET2 Timeout Parameters JP10/JP11 Coax / Twisted Pair Select (CN120ST/SBT only) JP12 Terminator Select (CN120AB/ST/SBT only) J1 BNC RG62/U Connector (all except CN120TP) J2 Two 6-position Telephone Jack (CN120TP/ST/SBT only) Setting one of the switches to Off means "1", On means "0". Setting the Node ID ^^^^^^^^^^^^^^^^^^^ The eight switches in SW2 are used to set the node ID. Each node attached to the network must have an unique node ID which must be different from 0. Switch 1 (ID0) serves as the least significant bit (LSB). The node ID is the sum of the values of all switches set to "1" These values are: ======= ====== ===== Switch Label Value ======= ====== ===== 1 ID0 1 2 ID1 2 3 ID2 4 4 ID3 8 5 ID4 16 6 ID5 32 7 ID6 64 8 ID7 128 ======= ====== ===== Some Examples:: Switch | Hex | Decimal 8 7 6 5 4 3 2 1 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed 0 0 0 0 0 0 0 1 | 1 | 1 0 0 0 0 0 0 1 0 | 2 | 2 0 0 0 0 0 0 1 1 | 3 | 3 . . . | | 0 1 0 1 0 1 0 1 | 55 | 85 . . . | | 1 0 1 0 1 0 1 0 | AA | 170 . . . | | 1 1 1 1 1 1 0 1 | FD | 253 1 1 1 1 1 1 1 0 | FE | 254 1 1 1 1 1 1 1 1 | FF | 255 Setting the I/O Base Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The last three switches in switch block SW1 are used to select one of eight possible I/O Base addresses using the following table:: Switch | Hex I/O 6 7 8 | Address ------------|-------- ON ON ON | 260 OFF ON ON | 290 ON OFF ON | 2E0 (Manufacturer's default) OFF OFF ON | 2F0 ON ON OFF | 300 OFF ON OFF | 350 ON OFF OFF | 380 OFF OFF OFF | 3E0 Setting the Base Memory (RAM) buffer Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The memory buffer (RAM) requires 2K. The base of this buffer can be located in any of eight positions. The address of the Boot Prom is memory base + 8K or memory base + 0x2000. Switches 1-5 of switch block SW1 select the Memory Base address. :: Switch | Hex RAM | Hex ROM 1 2 3 4 5 | Address | Address *) --------------------|---------|----------- ON ON ON ON ON | C0000 | C2000 ON ON OFF ON ON | C4000 | C6000 ON ON ON OFF ON | CC000 | CE000 ON ON OFF OFF ON | D0000 | D2000 (Manufacturer's default) ON ON ON ON OFF | D4000 | D6000 ON ON OFF ON OFF | D8000 | DA000 ON ON ON OFF OFF | DC000 | DE000 ON ON OFF OFF OFF | E0000 | E2000 *) To enable the Boot ROM install the jumper JP1 .. note:: Since the switches 1 and 2 are always set to ON it may be possible that they can be used to add an offset of 2K, 4K or 6K to the base address, but this feature is not documented in the manual and I haven't tested it yet. Setting the Interrupt Line ^^^^^^^^^^^^^^^^^^^^^^^^^^ To select a hardware interrupt level install one (only one!) of the jumpers JP2, JP3, JP4, JP5, JP6. JP2 is the default:: Jumper | IRQ -------|----- 2 | 2 3 | 3 4 | 4 5 | 5 6 | 7 Setting the Internal Terminator on CN120AB/TP/SBT ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The jumper JP12 is used to enable the internal terminator:: ----- 0 | 0 | ----- ON | | ON | 0 | | 0 | | | OFF ----- OFF | 0 | 0 ----- Terminator Terminator disabled enabled Selecting the Connector Type on CN120ST/SBT ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ :: JP10 JP11 JP10 JP11 ----- ----- 0 0 | 0 | | 0 | ----- ----- | | | | | 0 | | 0 | | 0 | | 0 | | | | | ----- ----- | 0 | | 0 | 0 0 ----- ----- Coaxial Cable Twisted Pair Cable (Default) Setting the Timeout Parameters ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The jumpers labeled EXT1 and EXT2 are used to determine the timeout parameters. These two jumpers are normally left open. CNet Technology Inc. (16-bit cards) =================================== 160 Series (16-bit cards) ------------------------- - from Juergen Seifert <seifert@htwm.de> This description has been written by Juergen Seifert <seifert@htwm.de> using information from the following Original CNet Manual "ARCNET USER'S MANUAL for CN160A CN160AB CN160TP P/N:12-01-0006 Revision 3.00" ARCNET is a registered trademark of the Datapoint Corporation - P/N 160A ARCNET 16 bit XT/AT Star - P/N 160AB ARCNET 16 bit XT/AT Bus - P/N 160TP ARCNET 16 bit XT/AT Twisted Pair :: ___________________________________________________________________ < _________________________ ___| > |oo| JP2 | | LED |___| < |oo| JP1 | 9026 | LED |___| > |_________________________| ___| < N | | ID7 > 1 o | | ID6 < 1 2 3 4 5 6 7 8 9 0 d | S | ID5 > _______________ _____________________ e | W | ID4 < | PROM | | SW1 | A | 2 | ID3 > > SOCKET | |_____________________| d | | ID2 < |_______________| | IO-Base | MEM | d | | ID1 > r |___| ID0 < ____| > | | < | J1 | > | | < |____| > 1 1 1 1 | < 3 4 5 6 7 JP 8 9 0 1 2 3 | > |o|o|o|o|o| |o|o|o|o|o|o| | < |o|o|o|o|o| __ |o|o|o|o|o|o| ___________| > | | | <____________| |_______________________________________| Legend:: 9026 ARCNET Probe SW1 1-6: Base I/O Address Select 7-10: Base Memory Address Select SW2 1-8: Node ID Select (ID0-ID7) JP1/JP2 ET1, ET2 Timeout Parameters JP3-JP13 Interrupt Select J1 BNC RG62/U Connector (CN160A/AB only) J1 Two 6-position Telephone Jack (CN160TP only) LED Setting one of the switches to Off means "1", On means "0". Setting the Node ID ^^^^^^^^^^^^^^^^^^^ The eight switches in SW2 are used to set the node ID. Each node attached to the network must have an unique node ID which must be different from 0. Switch 1 (ID0) serves as the least significant bit (LSB). The node ID is the sum of the values of all switches set to "1" These values are:: Switch | Label | Value -------|-------|------- 1 | ID0 | 1 2 | ID1 | 2 3 | ID2 | 4 4 | ID3 | 8 5 | ID4 | 16 6 | ID5 | 32 7 | ID6 | 64 8 | ID7 | 128 Some Examples:: Switch | Hex | Decimal 8 7 6 5 4 3 2 1 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed 0 0 0 0 0 0 0 1 | 1 | 1 0 0 0 0 0 0 1 0 | 2 | 2 0 0 0 0 0 0 1 1 | 3 | 3 . . . | | 0 1 0 1 0 1 0 1 | 55 | 85 . . . | | 1 0 1 0 1 0 1 0 | AA | 170 . . . | | 1 1 1 1 1 1 0 1 | FD | 253 1 1 1 1 1 1 1 0 | FE | 254 1 1 1 1 1 1 1 1 | FF | 255 Setting the I/O Base Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The first six switches in switch block SW1 are used to select the I/O Base address using the following table:: Switch | Hex I/O 1 2 3 4 5 6 | Address ------------------------|-------- OFF ON ON OFF OFF ON | 260 OFF ON OFF ON ON OFF | 290 OFF ON OFF OFF OFF ON | 2E0 (Manufacturer's default) OFF ON OFF OFF OFF OFF | 2F0 OFF OFF ON ON ON ON | 300 OFF OFF ON OFF ON OFF | 350 OFF OFF OFF ON ON ON | 380 OFF OFF OFF OFF OFF ON | 3E0 Note: Other IO-Base addresses seem to be selectable, but only the above combinations are documented. Setting the Base Memory (RAM) buffer Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The switches 7-10 of switch block SW1 are used to select the Memory Base address of the RAM (2K) and the PROM:: Switch | Hex RAM | Hex ROM 7 8 9 10 | Address | Address ----------------|---------|----------- OFF OFF ON ON | C0000 | C8000 OFF OFF ON OFF | D0000 | D8000 (Default) OFF OFF OFF ON | E0000 | E8000 .. note:: Other MEM-Base addresses seem to be selectable, but only the above combinations are documented. Setting the Interrupt Line ^^^^^^^^^^^^^^^^^^^^^^^^^^ To select a hardware interrupt level install one (only one!) of the jumpers JP3 through JP13 using the following table:: Jumper | IRQ -------|----------------- 3 | 14 4 | 15 5 | 12 6 | 11 7 | 10 8 | 3 9 | 4 10 | 5 11 | 6 12 | 7 13 | 2 (=9) Default! .. note:: - Do not use JP11=IRQ6, it may conflict with your Floppy Disk Controller - Use JP3=IRQ14 only, if you don't have an IDE-, MFM-, or RLL- Hard Disk, it may conflict with their controllers Setting the Timeout Parameters ------------------------------ The jumpers labeled JP1 and JP2 are used to determine the timeout parameters. These two jumpers are normally left open. Lantech ======= 8-bit card, unknown model ------------------------- - from Vlad Lungu <vlungu@ugal.ro> - his e-mail address seemed broken at the time I tried to reach him. Sorry Vlad, if you didn't get my reply. :: ________________________________________________________________ | 1 8 | | ___________ __| | | SW1 | LED |__| | |__________| | | ___| | _____________________ |S | 8 | | | |W | | | | |2 | | | | |__| 1 | | UM9065L | |o| JP4 ____|____ | | | |o| | CN | | | | |________| | | | | | |___________________| | | | | | | _____________ | | | | | | | PROM | |ooooo| JP6 | | |____________| |ooooo| | |_____________ _ _| |____________________________________________| |__| UM9065L : ARCnet Controller SW 1 : Shared Memory Address and I/O Base :: ON=0 12345|Memory Address -----|-------------- 00001| D4000 00010| CC000 00110| D0000 01110| D1000 01101| D9000 10010| CC800 10011| DC800 11110| D1800 It seems that the bits are considered in reverse order. Also, you must observe that some of those addresses are unusual and I didn't probe them; I used a memory dump in DOS to identify them. For the 00000 configuration and some others that I didn't write here the card seems to conflict with the video card (an S3 GENDAC). I leave the full decoding of those addresses to you. :: 678| I/O Address ---|------------ 000| 260 001| failed probe 010| 2E0 011| 380 100| 290 101| 350 110| failed probe 111| 3E0 SW 2 : Node ID (binary coded) JP 4 : Boot PROM enable CLOSE - enabled OPEN - disabled JP 6 : IRQ set (ONLY ONE jumper on 1-5 for IRQ 2-6) Acer ==== 8-bit card, Model 5210-003 -------------------------- - from Vojtech Pavlik <vojtech@suse.cz> using portions of the existing arcnet-hardware file. This is a 90C26 based card. Its configuration seems similar to the SMC PC100, but has some additional jumpers I don't know the meaning of. :: __ | | ___________|__|_________________________ | | | | | | BNC | | | |______| ___| | _____________________ |___ | | | | | | Hybrid IC | | | | | o|o J1 | | |_____________________| 8|8 | | 8|8 J5 | | o|o | | 8|8 | |__ 8|8 | (|__| LED o|o | | 8|8 | | 8|8 J15 | | | | _____ | | | | _____ | | | | | | ___| | | | | | | | _____ | ROM | | UFS | | | | | | | | | | | | | ___ | | | | | | | | | | |__.__| |__.__| | | | NCR | |XTL| _____ _____ | | | | |___| | | | | | | |90C26| | | | | | | | | | RAM | | UFS | | | | | J17 o|o | | | | | | | | J16 o|o | | | | | | |__.__| |__.__| |__.__| | | ___ | | | |8 | | |SW2| | | | | | | |___|1 | | ___ | | | |10 J18 o|o | | | | o|o | | |SW1| o|o | | | | J21 o|o | | |___|1 | | | |____________________________________| Legend:: 90C26 ARCNET Chip XTL 20 MHz Crystal SW1 1-6 Base I/O Address Select 7-10 Memory Address Select SW2 1-8 Node ID Select (ID0-ID7) J1-J5 IRQ Select J6-J21 Unknown (Probably extra timeouts & ROM enable ...) LED1 Activity LED BNC Coax connector (STAR ARCnet) RAM 2k of SRAM ROM Boot ROM socket UFS Unidentified Flying Sockets Setting the Node ID ^^^^^^^^^^^^^^^^^^^ The eight switches in SW2 are used to set the node ID. Each node attached to the network must have an unique node ID which must not be 0. Switch 1 (ID0) serves as the least significant bit (LSB). Setting one of the switches to OFF means "1", ON means "0". The node ID is the sum of the values of all switches set to "1" These values are:: Switch | Value -------|------- 1 | 1 2 | 2 3 | 4 4 | 8 5 | 16 6 | 32 7 | 64 8 | 128 Don't set this to 0 or 255; these values are reserved. Setting the I/O Base Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The switches 1 to 6 of switch block SW1 are used to select one of 32 possible I/O Base addresses using the following tables:: | Hex Switch | Value -------|------- 1 | 200 2 | 100 3 | 80 4 | 40 5 | 20 6 | 10 The I/O address is sum of all switches set to "1". Remember that the I/O address space below 0x200 is RESERVED for mainboard, so switch 1 should be ALWAYS SET TO OFF. Setting the Base Memory (RAM) buffer Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The memory buffer (RAM) requires 2K. The base of this buffer can be located in any of sixteen positions. However, the addresses below A0000 are likely to cause system hang because there's main RAM. Jumpers 7-10 of switch block SW1 select the Memory Base address:: Switch | Hex RAM 7 8 9 10 | Address ----------------|--------- OFF OFF OFF OFF | F0000 (conflicts with main BIOS) OFF OFF OFF ON | E0000 OFF OFF ON OFF | D0000 OFF OFF ON ON | C0000 (conflicts with video BIOS) OFF ON OFF OFF | B0000 (conflicts with mono video) OFF ON OFF ON | A0000 (conflicts with graphics) Setting the Interrupt Line ^^^^^^^^^^^^^^^^^^^^^^^^^^ Jumpers 1-5 of the jumper block J1 control the IRQ level. ON means shorted, OFF means open:: Jumper | IRQ 1 2 3 4 5 | ---------------------------- ON OFF OFF OFF OFF | 7 OFF ON OFF OFF OFF | 5 OFF OFF ON OFF OFF | 4 OFF OFF OFF ON OFF | 3 OFF OFF OFF OFF ON | 2 Unknown jumpers & sockets ^^^^^^^^^^^^^^^^^^^^^^^^^ I know nothing about these. I just guess that J16&J17 are timeout jumpers and maybe one of J18-J21 selects ROM. Also J6-J10 and J11-J15 are connecting IRQ2-7 to some pins on the UFSs. I can't guess the purpose. Datapoint? ========== LAN-ARC-8, an 8-bit card ------------------------ - from Vojtech Pavlik <vojtech@suse.cz> This is another SMC 90C65-based ARCnet card. I couldn't identify the manufacturer, but it might be DataPoint, because the card has the original arcNet logo in its upper right corner. :: _______________________________________________________ | _________ | | | SW2 | ON arcNet | | |_________| OFF ___| | _____________ 1 ______ 8 | | 8 | | | SW1 | XTAL | ____________ | S | | > RAM (2k) | |______|| | | W | | |_____________| | H | | 3 | | _________|_____ y | |___| 1 | _________ | | |b | | | |_________| | | |r | | | | SMC | |i | | | | 90C65| |d | | | _________ | | | | | | | SW1 | ON | | |I | | | |_________| OFF |_________|_____/C | _____| | 1 8 | | | |___ | ______________ | | | BNC |___| | | | |____________| |_____| | > EPROM SOCKET | _____________ | | |______________| |_____________| | | ______________| | | |________________________________________| Legend:: 90C65 ARCNET Chip SW1 1-5: Base Memory Address Select 6-8: Base I/O Address Select SW2 1-8: Node ID Select SW3 1-5: IRQ Select 6-7: Extra Timeout 8 : ROM Enable BNC Coax connector XTAL 20 MHz Crystal Setting the Node ID ^^^^^^^^^^^^^^^^^^^ The eight switches in SW3 are used to set the node ID. Each node attached to the network must have an unique node ID which must not be 0. Switch 1 serves as the least significant bit (LSB). Setting one of the switches to Off means "1", On means "0". The node ID is the sum of the values of all switches set to "1" These values are:: Switch | Value -------|------- 1 | 1 2 | 2 3 | 4 4 | 8 5 | 16 6 | 32 7 | 64 8 | 128 Setting the I/O Base Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The last three switches in switch block SW1 are used to select one of eight possible I/O Base addresses using the following table:: Switch | Hex I/O 6 7 8 | Address ------------|-------- ON ON ON | 260 OFF ON ON | 290 ON OFF ON | 2E0 (Manufacturer's default) OFF OFF ON | 2F0 ON ON OFF | 300 OFF ON OFF | 350 ON OFF OFF | 380 OFF OFF OFF | 3E0 Setting the Base Memory (RAM) buffer Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The memory buffer (RAM) requires 2K. The base of this buffer can be located in any of eight positions. The address of the Boot Prom is memory base + 0x2000. Jumpers 3-5 of switch block SW1 select the Memory Base address. :: Switch | Hex RAM | Hex ROM 1 2 3 4 5 | Address | Address *) --------------------|---------|----------- ON ON ON ON ON | C0000 | C2000 ON ON OFF ON ON | C4000 | C6000 ON ON ON OFF ON | CC000 | CE000 ON ON OFF OFF ON | D0000 | D2000 (Manufacturer's default) ON ON ON ON OFF | D4000 | D6000 ON ON OFF ON OFF | D8000 | DA000 ON ON ON OFF OFF | DC000 | DE000 ON ON OFF OFF OFF | E0000 | E2000 *) To enable the Boot ROM set the switch 8 of switch block SW3 to position ON. The switches 1 and 2 probably add 0x0800 and 0x1000 to RAM base address. Setting the Interrupt Line ^^^^^^^^^^^^^^^^^^^^^^^^^^ Switches 1-5 of the switch block SW3 control the IRQ level:: Jumper | IRQ 1 2 3 4 5 | ---------------------------- ON OFF OFF OFF OFF | 3 OFF ON OFF OFF OFF | 4 OFF OFF ON OFF OFF | 5 OFF OFF OFF ON OFF | 7 OFF OFF OFF OFF ON | 2 Setting the Timeout Parameters ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The switches 6-7 of the switch block SW3 are used to determine the timeout parameters. These two switches are normally left in the OFF position. Topware ======= 8-bit card, TA-ARC/10 --------------------- - from Vojtech Pavlik <vojtech@suse.cz> This is another very similar 90C65 card. Most of the switches and jumpers are the same as on other clones. :: _____________________________________________________________________ | ___________ | | ______ | | |SW2 NODE ID| | | | XTAL | | | |___________| | Hybrid IC | |______| | | ___________ | | __| | |SW1 MEM+I/O| |_________________________| LED1|__|) | |___________| 1 2 | | J3 |o|o| TIMEOUT ______| | ______________ |o|o| | | | | | ___________________ | RJ | | > EPROM SOCKET | | \ |------| |J2 |______________| | | | | ||o| | | |______| ||o| ROM ENABLE | SMC | _________ | | _____________ | 90C65 | |_________| _____| | | | | | | |___ | > RAM (2k) | | | | BNC |___| | |_____________| | | |_____| | |____________________| | | ________ IRQ 2 3 4 5 7 ___________ | ||________| |o|o|o|o|o| |___________| | |________ J1|o|o|o|o|o| ______________| | | |_____________________________________________| Legend:: 90C65 ARCNET Chip XTAL 20 MHz Crystal SW1 1-5 Base Memory Address Select 6-8 Base I/O Address Select SW2 1-8 Node ID Select (ID0-ID7) J1 IRQ Select J2 ROM Enable J3 Extra Timeout LED1 Activity LED BNC Coax connector (BUS ARCnet) RJ Twisted Pair Connector (daisy chain) Setting the Node ID ^^^^^^^^^^^^^^^^^^^ The eight switches in SW2 are used to set the node ID. Each node attached to the network must have an unique node ID which must not be 0. Switch 1 (ID0) serves as the least significant bit (LSB). Setting one of the switches to Off means "1", On means "0". The node ID is the sum of the values of all switches set to "1" These values are:: Switch | Label | Value -------|-------|------- 1 | ID0 | 1 2 | ID1 | 2 3 | ID2 | 4 4 | ID3 | 8 5 | ID4 | 16 6 | ID5 | 32 7 | ID6 | 64 8 | ID7 | 128 Setting the I/O Base Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The last three switches in switch block SW1 are used to select one of eight possible I/O Base addresses using the following table:: Switch | Hex I/O 6 7 8 | Address ------------|-------- ON ON ON | 260 (Manufacturer's default) OFF ON ON | 290 ON OFF ON | 2E0 OFF OFF ON | 2F0 ON ON OFF | 300 OFF ON OFF | 350 ON OFF OFF | 380 OFF OFF OFF | 3E0 Setting the Base Memory (RAM) buffer Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The memory buffer (RAM) requires 2K. The base of this buffer can be located in any of eight positions. The address of the Boot Prom is memory base + 0x2000. Jumpers 3-5 of switch block SW1 select the Memory Base address. :: Switch | Hex RAM | Hex ROM 1 2 3 4 5 | Address | Address *) --------------------|---------|----------- ON ON ON ON ON | C0000 | C2000 ON ON OFF ON ON | C4000 | C6000 (Manufacturer's default) ON ON ON OFF ON | CC000 | CE000 ON ON OFF OFF ON | D0000 | D2000 ON ON ON ON OFF | D4000 | D6000 ON ON OFF ON OFF | D8000 | DA000 ON ON ON OFF OFF | DC000 | DE000 ON ON OFF OFF OFF | E0000 | E2000 *) To enable the Boot ROM short the jumper J2. The jumpers 1 and 2 probably add 0x0800 and 0x1000 to RAM address. Setting the Interrupt Line ^^^^^^^^^^^^^^^^^^^^^^^^^^ Jumpers 1-5 of the jumper block J1 control the IRQ level. ON means shorted, OFF means open:: Jumper | IRQ 1 2 3 4 5 | ---------------------------- ON OFF OFF OFF OFF | 2 OFF ON OFF OFF OFF | 3 OFF OFF ON OFF OFF | 4 OFF OFF OFF ON OFF | 5 OFF OFF OFF OFF ON | 7 Setting the Timeout Parameters ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The jumpers J3 are used to set the timeout parameters. These two jumpers are normally left open. Thomas-Conrad ============= Model #500-6242-0097 REV A (8-bit card) --------------------------------------- - from Lars Karlsson <100617.3473@compuserve.com> :: ________________________________________________________ | ________ ________ |_____ | |........| |........| | | |________| |________| ___| | SW 3 SW 1 | | | Base I/O Base Addr. Station | | | address | | | ______ switch | | | | | | | | | | |___| | | | ______ |___._ | |______| |______| ____| BNC | Jumper- _____| Connector | Main chip block _ __| ' | | | | RJ Connector | |_| | with 110 Ohm | |__ Terminator | ___________ __| | |...........| | RJ-jack | |...........| _____ | (unused) | |___________| |_____| |__ | Boot PROM socket IRQ-jumpers |_ Diagnostic |________ __ _| LED (red) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |________| | | And here are the settings for some of the switches and jumpers on the cards. :: I/O 1 2 3 4 5 6 7 8 2E0----- 0 0 0 1 0 0 0 1 2F0----- 0 0 0 1 0 0 0 0 300----- 0 0 0 0 1 1 1 1 350----- 0 0 0 0 1 1 1 0 "0" in the above example means switch is off "1" means that it is on. :: ShMem address. 1 2 3 4 5 6 7 8 CX00--0 0 1 1 | | | DX00--0 0 1 0 | X000--------- 1 1 | X400--------- 1 0 | X800--------- 0 1 | XC00--------- 0 0 ENHANCED----------- 1 COMPATIBLE--------- 0 :: IRQ 3 4 5 7 2 . . . . . . . . . . There is a DIP-switch with 8 switches, used to set the shared memory address to be used. The first 6 switches set the address, the 7th doesn't have any function, and the 8th switch is used to select "compatible" or "enhanced". When I got my two cards, one of them had this switch set to "enhanced". That card didn't work at all, it wasn't even recognized by the driver. The other card had this switch set to "compatible" and it behaved absolutely normally. I guess that the switch on one of the cards, must have been changed accidentally when the card was taken out of its former host. The question remains unanswered, what is the purpose of the "enhanced" position? [Avery's note: "enhanced" probably either disables shared memory (use IO ports instead) or disables IO ports (use memory addresses instead). This varies by the type of card involved. I fail to see how either of these enhance anything. Send me more detailed information about this mode, or just use "compatible" mode instead.] Waterloo Microsystems Inc. ?? ============================= 8-bit card (C) 1985 ------------------- - from Robert Michael Best <rmb117@cs.usask.ca> [Avery's note: these don't work with my driver for some reason. These cards SEEM to have settings similar to the PDI508Plus, which is software-configured and doesn't work with my driver either. The "Waterloo chip" is a boot PROM, probably designed specifically for the University of Waterloo. If you have any further information about this card, please e-mail me.] The probe has not been able to detect the card on any of the J2 settings, and I tried them again with the "Waterloo" chip removed. :: _____________________________________________________________________ | \/ \/ ___ __ __ | | C4 C4 |^| | M || ^ ||^| | | -- -- |_| | 5 || || | C3 | | \/ \/ C10 |___|| ||_| | | C4 C4 _ _ | | ?? | | -- -- | \/ || | | | | || | | | | || C1 | | | | || | \/ _____| | | C6 || | C9 | |___ | | || | -- | BNC |___| | | || | >C7| |_____| | | || | | | __ __ |____||_____| 1 2 3 6 | || ^ | >C4| |o|o|o|o|o|o| J2 >C4| | || | |o|o|o|o|o|o| | || C2 | >C4| >C4| | || | >C8| | || | 2 3 4 5 6 7 IRQ >C4| | ||_____| |o|o|o|o|o|o| J3 | |_______ |o|o|o|o|o|o| _______________| | | |_____________________________________________| C1 -- "COM9026 SMC 8638" In a chip socket. C2 -- "@Copyright Waterloo Microsystems Inc. 1985" In a chip Socket with info printed on a label covering a round window showing the circuit inside. (The window indicates it is an EPROM chip.) C3 -- "COM9032 SMC 8643" In a chip socket. C4 -- "74LS" 9 total no sockets. M5 -- "50006-136 20.000000 MHZ MTQ-T1-S3 0 M-TRON 86-40" Metallic case with 4 pins, no socket. C6 -- "MOSTEK@TC8643 MK6116N-20 MALAYSIA" No socket. C7 -- No stamp or label but in a 20 pin chip socket. C8 -- "PAL10L8CN 8623" In a 20 pin socket. C9 -- "PAl16R4A-2CN 8641" In a 20 pin socket. C10 -- "M8640 NMC 9306N" In an 8 pin socket. ?? -- Some components on a smaller board and attached with 20 pins all along the side closest to the BNC connector. The are coated in a dark resin. On the board there are two jumper banks labeled J2 and J3. The manufacturer didn't put a J1 on the board. The two boards I have both came with a jumper box for each bank. :: J2 -- Numbered 1 2 3 4 5 6. 4 and 5 are not stamped due to solder points. J3 -- IRQ 2 3 4 5 6 7 The board itself has a maple leaf stamped just above the irq jumpers and "-2 46-86" beside C2. Between C1 and C6 "ASS 'Y 300163" and "@1986 CORMAN CUSTOM ELECTRONICS CORP." stamped just below the BNC connector. Below that "MADE IN CANADA" No Name ======= 8-bit cards, 16-bit cards ------------------------- - from Juergen Seifert <seifert@htwm.de> I have named this ARCnet card "NONAME", since there is no name of any manufacturer on the Installation manual nor on the shipping box. The only hint to the existence of a manufacturer at all is written in copper, it is "Made in Taiwan" This description has been written by Juergen Seifert <seifert@htwm.de> using information from the Original "ARCnet Installation Manual" :: ________________________________________________________________ | |STAR| BUS| T/P| | | |____|____|____| | | _____________________ | | | | | | | | | | | | | | | SMC | | | | | | | | COM90C65 | | | | | | | | | | | |__________-__________| | | _____| | _______________ | CN | | | PROM | |_____| | > SOCKET | | | |_______________| 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 | | _______________ _______________ | | |o|o|o|o|o|o|o|o| | SW1 || SW2 || | |o|o|o|o|o|o|o|o| |_______________||_______________|| |___ 2 3 4 5 7 E E R Node ID IOB__|__MEM____| | \ IRQ / T T O | |__________________1_2_M______________________| Legend:: COM90C65: ARCnet Probe S1 1-8: Node ID Select S2 1-3: I/O Base Address Select 4-6: Memory Base Address Select 7-8: RAM Offset Select ET1, ET2 Extended Timeout Select ROM ROM Enable Select CN RG62 Coax Connector STAR| BUS | T/P Three fields for placing a sign (colored circle) indicating the topology of the card Setting one of the switches to Off means "1", On means "0". Setting the Node ID ^^^^^^^^^^^^^^^^^^^ The eight switches in group SW1 are used to set the node ID. Each node attached to the network must have an unique node ID which must be different from 0. Switch 8 serves as the least significant bit (LSB). The node ID is the sum of the values of all switches set to "1" These values are:: Switch | Value -------|------- 8 | 1 7 | 2 6 | 4 5 | 8 4 | 16 3 | 32 2 | 64 1 | 128 Some Examples:: Switch | Hex | Decimal 1 2 3 4 5 6 7 8 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed 0 0 0 0 0 0 0 1 | 1 | 1 0 0 0 0 0 0 1 0 | 2 | 2 0 0 0 0 0 0 1 1 | 3 | 3 . . . | | 0 1 0 1 0 1 0 1 | 55 | 85 . . . | | 1 0 1 0 1 0 1 0 | AA | 170 . . . | | 1 1 1 1 1 1 0 1 | FD | 253 1 1 1 1 1 1 1 0 | FE | 254 1 1 1 1 1 1 1 1 | FF | 255 Setting the I/O Base Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The first three switches in switch group SW2 are used to select one of eight possible I/O Base addresses using the following table:: Switch | Hex I/O 1 2 3 | Address ------------|-------- ON ON ON | 260 ON ON OFF | 290 ON OFF ON | 2E0 (Manufacturer's default) ON OFF OFF | 2F0 OFF ON ON | 300 OFF ON OFF | 350 OFF OFF ON | 380 OFF OFF OFF | 3E0 Setting the Base Memory (RAM) buffer Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The memory buffer requires 2K of a 16K block of RAM. The base of this 16K block can be located in any of eight positions. Switches 4-6 of switch group SW2 select the Base of the 16K block. Within that 16K address space, the buffer may be assigned any one of four positions, determined by the offset, switches 7 and 8 of group SW2. :: Switch | Hex RAM | Hex ROM 4 5 6 7 8 | Address | Address *) -----------|---------|----------- 0 0 0 0 0 | C0000 | C2000 0 0 0 0 1 | C0800 | C2000 0 0 0 1 0 | C1000 | C2000 0 0 0 1 1 | C1800 | C2000 | | 0 0 1 0 0 | C4000 | C6000 0 0 1 0 1 | C4800 | C6000 0 0 1 1 0 | C5000 | C6000 0 0 1 1 1 | C5800 | C6000 | | 0 1 0 0 0 | CC000 | CE000 0 1 0 0 1 | CC800 | CE000 0 1 0 1 0 | CD000 | CE000 0 1 0 1 1 | CD800 | CE000 | | 0 1 1 0 0 | D0000 | D2000 (Manufacturer's default) 0 1 1 0 1 | D0800 | D2000 0 1 1 1 0 | D1000 | D2000 0 1 1 1 1 | D1800 | D2000 | | 1 0 0 0 0 | D4000 | D6000 1 0 0 0 1 | D4800 | D6000 1 0 0 1 0 | D5000 | D6000 1 0 0 1 1 | D5800 | D6000 | | 1 0 1 0 0 | D8000 | DA000 1 0 1 0 1 | D8800 | DA000 1 0 1 1 0 | D9000 | DA000 1 0 1 1 1 | D9800 | DA000 | | 1 1 0 0 0 | DC000 | DE000 1 1 0 0 1 | DC800 | DE000 1 1 0 1 0 | DD000 | DE000 1 1 0 1 1 | DD800 | DE000 | | 1 1 1 0 0 | E0000 | E2000 1 1 1 0 1 | E0800 | E2000 1 1 1 1 0 | E1000 | E2000 1 1 1 1 1 | E1800 | E2000 *) To enable the 8K Boot PROM install the jumper ROM. The default is jumper ROM not installed. Setting Interrupt Request Lines (IRQ) ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ To select a hardware interrupt level set one (only one!) of the jumpers IRQ2, IRQ3, IRQ4, IRQ5 or IRQ7. The manufacturer's default is IRQ2. Setting the Timeouts ^^^^^^^^^^^^^^^^^^^^ The two jumpers labeled ET1 and ET2 are used to determine the timeout parameters (response and reconfiguration time). Every node in a network must be set to the same timeout values. :: ET1 ET2 | Response Time (us) | Reconfiguration Time (ms) --------|--------------------|-------------------------- Off Off | 78 | 840 (Default) Off On | 285 | 1680 On Off | 563 | 1680 On On | 1130 | 1680 On means jumper installed, Off means jumper not installed 16-BIT ARCNET ------------- The manual of my 8-Bit NONAME ARCnet Card contains another description of a 16-Bit Coax / Twisted Pair Card. This description is incomplete, because there are missing two pages in the manual booklet. (The table of contents reports pages ... 2-9, 2-11, 2-12, 3-1, ... but inside the booklet there is a different way of counting ... 2-9, 2-10, A-1, (empty page), 3-1, ..., 3-18, A-1 (again), A-2) Also the picture of the board layout is not as good as the picture of 8-Bit card, because there isn't any letter like "SW1" written to the picture. Should somebody have such a board, please feel free to complete this description or to send a mail to me! This description has been written by Juergen Seifert <seifert@htwm.de> using information from the Original "ARCnet Installation Manual" :: ___________________________________________________________________ < _________________ _________________ | > | SW? || SW? | | < |_________________||_________________| | > ____________________ | < | | | > | | | < | | | > | | | < | | | > | | | < | | | > |____________________| | < ____| > ____________________ | | < | | | J1 | > | < | | < |____________________| ? ? ? ? ? ? |____| > |o|o|o|o|o|o| | < |o|o|o|o|o|o| | > | < __ ___________| > | | | <____________| |_______________________________________| Setting one of the switches to Off means "1", On means "0". Setting the Node ID ^^^^^^^^^^^^^^^^^^^ The eight switches in group SW2 are used to set the node ID. Each node attached to the network must have an unique node ID which must be different from 0. Switch 8 serves as the least significant bit (LSB). The node ID is the sum of the values of all switches set to "1" These values are:: Switch | Value -------|------- 8 | 1 7 | 2 6 | 4 5 | 8 4 | 16 3 | 32 2 | 64 1 | 128 Some Examples:: Switch | Hex | Decimal 1 2 3 4 5 6 7 8 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed 0 0 0 0 0 0 0 1 | 1 | 1 0 0 0 0 0 0 1 0 | 2 | 2 0 0 0 0 0 0 1 1 | 3 | 3 . . . | | 0 1 0 1 0 1 0 1 | 55 | 85 . . . | | 1 0 1 0 1 0 1 0 | AA | 170 . . . | | 1 1 1 1 1 1 0 1 | FD | 253 1 1 1 1 1 1 1 0 | FE | 254 1 1 1 1 1 1 1 1 | FF | 255 Setting the I/O Base Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The first three switches in switch group SW1 are used to select one of eight possible I/O Base addresses using the following table:: Switch | Hex I/O 3 2 1 | Address ------------|-------- ON ON ON | 260 ON ON OFF | 290 ON OFF ON | 2E0 (Manufacturer's default) ON OFF OFF | 2F0 OFF ON ON | 300 OFF ON OFF | 350 OFF OFF ON | 380 OFF OFF OFF | 3E0 Setting the Base Memory (RAM) buffer Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The memory buffer requires 2K of a 16K block of RAM. The base of this 16K block can be located in any of eight positions. Switches 6-8 of switch group SW1 select the Base of the 16K block. Within that 16K address space, the buffer may be assigned any one of four positions, determined by the offset, switches 4 and 5 of group SW1:: Switch | Hex RAM | Hex ROM 8 7 6 5 4 | Address | Address -----------|---------|----------- 0 0 0 0 0 | C0000 | C2000 0 0 0 0 1 | C0800 | C2000 0 0 0 1 0 | C1000 | C2000 0 0 0 1 1 | C1800 | C2000 | | 0 0 1 0 0 | C4000 | C6000 0 0 1 0 1 | C4800 | C6000 0 0 1 1 0 | C5000 | C6000 0 0 1 1 1 | C5800 | C6000 | | 0 1 0 0 0 | CC000 | CE000 0 1 0 0 1 | CC800 | CE000 0 1 0 1 0 | CD000 | CE000 0 1 0 1 1 | CD800 | CE000 | | 0 1 1 0 0 | D0000 | D2000 (Manufacturer's default) 0 1 1 0 1 | D0800 | D2000 0 1 1 1 0 | D1000 | D2000 0 1 1 1 1 | D1800 | D2000 | | 1 0 0 0 0 | D4000 | D6000 1 0 0 0 1 | D4800 | D6000 1 0 0 1 0 | D5000 | D6000 1 0 0 1 1 | D5800 | D6000 | | 1 0 1 0 0 | D8000 | DA000 1 0 1 0 1 | D8800 | DA000 1 0 1 1 0 | D9000 | DA000 1 0 1 1 1 | D9800 | DA000 | | 1 1 0 0 0 | DC000 | DE000 1 1 0 0 1 | DC800 | DE000 1 1 0 1 0 | DD000 | DE000 1 1 0 1 1 | DD800 | DE000 | | 1 1 1 0 0 | E0000 | E2000 1 1 1 0 1 | E0800 | E2000 1 1 1 1 0 | E1000 | E2000 1 1 1 1 1 | E1800 | E2000 Setting Interrupt Request Lines (IRQ) ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ?????????????????????????????????????? Setting the Timeouts ^^^^^^^^^^^^^^^^^^^^ ?????????????????????????????????????? 8-bit cards ("Made in Taiwan R.O.C.") ------------------------------------- - from Vojtech Pavlik <vojtech@suse.cz> I have named this ARCnet card "NONAME", since I got only the card with no manual at all and the only text identifying the manufacturer is "MADE IN TAIWAN R.O.C" printed on the card. :: ____________________________________________________________ | 1 2 3 4 5 6 7 8 | | |o|o| JP1 o|o|o|o|o|o|o|o| ON | | + o|o|o|o|o|o|o|o| ___| | _____________ o|o|o|o|o|o|o|o| OFF _____ | | ID7 | | | SW1 | | | | ID6 | > RAM (2k) | ____________________ | H | | S | ID5 | |_____________| | || y | | W | ID4 | | || b | | 2 | ID3 | | || r | | | ID2 | | || i | | | ID1 | | 90C65 || d | |___| ID0 | SW3 | || | | | |o|o|o|o|o|o|o|o| ON | || I | | | |o|o|o|o|o|o|o|o| | || C | | | |o|o|o|o|o|o|o|o| OFF |____________________|| | _____| | 1 2 3 4 5 6 7 8 | | | |___ | ______________ | | | BNC |___| | | | |_____| |_____| | > EPROM SOCKET | | | |______________| | | ______________| | | |_____________________________________________| Legend:: 90C65 ARCNET Chip SW1 1-5: Base Memory Address Select 6-8: Base I/O Address Select SW2 1-8: Node ID Select (ID0-ID7) SW3 1-5: IRQ Select 6-7: Extra Timeout 8 : ROM Enable JP1 Led connector BNC Coax connector Although the jumpers SW1 and SW3 are marked SW, not JP, they are jumpers, not switches. Setting the jumpers to ON means connecting the upper two pins, off the bottom two - or - in case of IRQ setting, connecting none of them at all. Setting the Node ID ^^^^^^^^^^^^^^^^^^^ The eight switches in SW2 are used to set the node ID. Each node attached to the network must have an unique node ID which must not be 0. Switch 1 (ID0) serves as the least significant bit (LSB). Setting one of the switches to Off means "1", On means "0". The node ID is the sum of the values of all switches set to "1" These values are:: Switch | Label | Value -------|-------|------- 1 | ID0 | 1 2 | ID1 | 2 3 | ID2 | 4 4 | ID3 | 8 5 | ID4 | 16 6 | ID5 | 32 7 | ID6 | 64 8 | ID7 | 128 Some Examples:: Switch | Hex | Decimal 8 7 6 5 4 3 2 1 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed 0 0 0 0 0 0 0 1 | 1 | 1 0 0 0 0 0 0 1 0 | 2 | 2 0 0 0 0 0 0 1 1 | 3 | 3 . . . | | 0 1 0 1 0 1 0 1 | 55 | 85 . . . | | 1 0 1 0 1 0 1 0 | AA | 170 . . . | | 1 1 1 1 1 1 0 1 | FD | 253 1 1 1 1 1 1 1 0 | FE | 254 1 1 1 1 1 1 1 1 | FF | 255 Setting the I/O Base Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The last three switches in switch block SW1 are used to select one of eight possible I/O Base addresses using the following table:: Switch | Hex I/O 6 7 8 | Address ------------|-------- ON ON ON | 260 OFF ON ON | 290 ON OFF ON | 2E0 (Manufacturer's default) OFF OFF ON | 2F0 ON ON OFF | 300 OFF ON OFF | 350 ON OFF OFF | 380 OFF OFF OFF | 3E0 Setting the Base Memory (RAM) buffer Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The memory buffer (RAM) requires 2K. The base of this buffer can be located in any of eight positions. The address of the Boot Prom is memory base + 0x2000. Jumpers 3-5 of jumper block SW1 select the Memory Base address. :: Switch | Hex RAM | Hex ROM 1 2 3 4 5 | Address | Address *) --------------------|---------|----------- ON ON ON ON ON | C0000 | C2000 ON ON OFF ON ON | C4000 | C6000 ON ON ON OFF ON | CC000 | CE000 ON ON OFF OFF ON | D0000 | D2000 (Manufacturer's default) ON ON ON ON OFF | D4000 | D6000 ON ON OFF ON OFF | D8000 | DA000 ON ON ON OFF OFF | DC000 | DE000 ON ON OFF OFF OFF | E0000 | E2000 *) To enable the Boot ROM set the jumper 8 of jumper block SW3 to position ON. The jumpers 1 and 2 probably add 0x0800, 0x1000 and 0x1800 to RAM adders. Setting the Interrupt Line ^^^^^^^^^^^^^^^^^^^^^^^^^^ Jumpers 1-5 of the jumper block SW3 control the IRQ level:: Jumper | IRQ 1 2 3 4 5 | ---------------------------- ON OFF OFF OFF OFF | 2 OFF ON OFF OFF OFF | 3 OFF OFF ON OFF OFF | 4 OFF OFF OFF ON OFF | 5 OFF OFF OFF OFF ON | 7 Setting the Timeout Parameters ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The jumpers 6-7 of the jumper block SW3 are used to determine the timeout parameters. These two jumpers are normally left in the OFF position. (Generic Model 9058) -------------------- - from Andrew J. Kroll <ag784@freenet.buffalo.edu> - Sorry this sat in my to-do box for so long, Andrew! (yikes - over a year!) :: _____ | < | .---' ________________________________________________________________ | | | | SW2 | | | | ___________ |_____________| | | | | | 1 2 3 4 5 6 ___| | | > 6116 RAM | _________ 8 | | | | |___________| |20MHzXtal| 7 | | | | |_________| __________ 6 | S | | | 74LS373 | |- 5 | W | | | _________ | E |- 4 | | | | >_______| ______________|..... P |- 3 | 3 | | | | | : O |- 2 | | | | | | : X |- 1 |___| | | ________________ | | : Y |- | | | | SW1 | | SL90C65 | : |- | | | |________________| | | : B |- | | | 1 2 3 4 5 6 7 8 | | : O |- | | | |_________o____|..../ A |- _______| | | ____________________ | R |- | |------, | | | | D |- | BNC | # | | > 2764 PROM SOCKET | |__________|- |_______|------' | |____________________| _________ | | | >________| <- 74LS245 | | | | | |___ ______________| | |H H H H H H H H H H H H H H H H H H H H H H H| | | |U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U| | | \| Legend:: SL90C65 ARCNET Controller / Transceiver /Logic SW1 1-5: IRQ Select 6: ET1 7: ET2 8: ROM ENABLE SW2 1-3: Memory Buffer/PROM Address 3-6: I/O Address Map SW3 1-8: Node ID Select BNC BNC RG62/U Connection *I* have had success using RG59B/U with *NO* terminators! What gives?! SW1: Timeouts, Interrupt and ROM ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ To select a hardware interrupt level set one (only one!) of the dip switches up (on) SW1...(switches 1-5) IRQ3, IRQ4, IRQ5, IRQ7, IRQ2. The Manufacturer's default is IRQ2. The switches on SW1 labeled EXT1 (switch 6) and EXT2 (switch 7) are used to determine the timeout parameters. These two dip switches are normally left off (down). To enable the 8K Boot PROM position SW1 switch 8 on (UP) labeled ROM. The default is jumper ROM not installed. Setting the I/O Base Address ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The last three switches in switch group SW2 are used to select one of eight possible I/O Base addresses using the following table:: Switch | Hex I/O 4 5 6 | Address -------|-------- 0 0 0 | 260 0 0 1 | 290 0 1 0 | 2E0 (Manufacturer's default) 0 1 1 | 2F0 1 0 0 | 300 1 0 1 | 350 1 1 0 | 380 1 1 1 | 3E0 Setting the Base Memory Address (RAM & ROM) ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The memory buffer requires 2K of a 16K block of RAM. The base of this 16K block can be located in any of eight positions. Switches 1-3 of switch group SW2 select the Base of the 16K block. (0 = DOWN, 1 = UP) I could, however, only verify two settings... :: Switch| Hex RAM | Hex ROM 1 2 3 | Address | Address ------|---------|----------- 0 0 0 | E0000 | E2000 0 0 1 | D0000 | D2000 (Manufacturer's default) 0 1 0 | ????? | ????? 0 1 1 | ????? | ????? 1 0 0 | ????? | ????? 1 0 1 | ????? | ????? 1 1 0 | ????? | ????? 1 1 1 | ????? | ????? Setting the Node ID ^^^^^^^^^^^^^^^^^^^ The eight switches in group SW3 are used to set the node ID. Each node attached to the network must have an unique node ID which must be different from 0. Switch 1 serves as the least significant bit (LSB). switches in the DOWN position are OFF (0) and in the UP position are ON (1) The node ID is the sum of the values of all switches set to "1" These values are:: Switch | Value -------|------- 1 | 1 2 | 2 3 | 4 4 | 8 5 | 16 6 | 32 7 | 64 8 | 128 Some Examples:: Switch# | Hex | Decimal 8 7 6 5 4 3 2 1 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed <-. 0 0 0 0 0 0 0 1 | 1 | 1 | 0 0 0 0 0 0 1 0 | 2 | 2 | 0 0 0 0 0 0 1 1 | 3 | 3 | . . . | | | 0 1 0 1 0 1 0 1 | 55 | 85 | . . . | | + Don't use 0 or 255! 1 0 1 0 1 0 1 0 | AA | 170 | . . . | | | 1 1 1 1 1 1 0 1 | FD | 253 | 1 1 1 1 1 1 1 0 | FE | 254 | 1 1 1 1 1 1 1 1 | FF | 255 <-' Tiara ===== (model unknown) --------------- - from Christoph Lameter <christoph@lameter.com> Here is information about my card as far as I could figure it out:: ----------------------------------------------- tiara Tiara LanCard of Tiara Computer Systems. +----------------------------------------------+ ! ! Transmitter Unit ! ! ! +------------------+ ------- ! MEM Coax Connector ! ROM 7654321 <- I/O ------- ! : : +--------+ ! ! : : ! 90C66LJ! +++ ! : : ! ! !D Switch to set ! : : ! ! !I the Nodenumber ! : : +--------+ !P ! !++ ! 234567 <- IRQ ! +------------!!!!!!!!!!!!!!!!!!!!!!!!--------+ !!!!!!!!!!!!!!!!!!!!!!!! - 0 = Jumper Installed - 1 = Open Top Jumper line Bit 7 = ROM Enable 654=Memory location 321=I/O Settings for Memory Location (Top Jumper Line) === ================ 456 Address selected === ================ 000 C0000 001 C4000 010 CC000 011 D0000 100 D4000 101 D8000 110 DC000 111 E0000 === ================ Settings for I/O Address (Top Jumper Line) === ==== 123 Port === ==== 000 260 001 290 010 2E0 011 2F0 100 300 101 350 110 380 111 3E0 === ==== Settings for IRQ Selection (Lower Jumper Line) ====== ===== 234567 ====== ===== 011111 IRQ 2 101111 IRQ 3 110111 IRQ 4 111011 IRQ 5 111110 IRQ 7 ====== ===== Other Cards =========== I have no information on other models of ARCnet cards at the moment. Please send any and all info to: apenwarr@worldvisions.ca Thanks. |