Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 | // SPDX-License-Identifier: GPL-2.0-or-later /* * PPA8548 Device Tree Source (36-bit address map) * Copyright 2013 Prodrive B.V. * * Based on: * MPC8548 CDS Device Tree Source (36-bit address map) * Copyright 2012 Freescale Semiconductor Inc. */ /include/ "mpc8548si-pre.dtsi" / { model = "ppa8548"; compatible = "ppa8548"; #address-cells = <2>; #size-cells = <2>; interrupt-parent = <&mpic>; memory { device_type = "memory"; reg = <0 0 0x0 0x40000000>; }; lbc: localbus@fe0005000 { reg = <0xf 0xe0005000 0 0x1000>; ranges = <0x0 0x0 0xf 0xff800000 0x00800000>; }; soc: soc8548@fe0000000 { ranges = <0 0xf 0xe0000000 0x100000>; }; pci0: pci@fe0008000 { /* ppa8548 board doesn't support PCI */ status = "disabled"; }; pci1: pci@fe0009000 { /* ppa8548 board doesn't support PCI */ status = "disabled"; }; pci2: pcie@fe000a000 { /* ppa8548 board doesn't support PCI */ status = "disabled"; }; rio: rapidio@fe00c0000 { reg = <0xf 0xe00c0000 0x0 0x11000>; port1 { ranges = <0x0 0x0 0x0 0x80000000 0x0 0x40000000>; }; }; }; &lbc { nor@0 { #address-cells = <1>; #size-cells = <1>; compatible = "cfi-flash"; reg = <0x0 0x0 0x00800000>; bank-width = <2>; device-width = <2>; partition@0 { reg = <0x0 0x7A0000>; label = "user"; }; partition@7A0000 { reg = <0x7A0000 0x20000>; label = "env"; read-only; }; partition@7C0000 { reg = <0x7C0000 0x40000>; label = "u-boot"; read-only; }; }; }; &soc { i2c@3000 { rtc@6f { compatible = "intersil,isl1208"; reg = <0x6f>; }; }; i2c@3100 { }; /* * Only ethernet controller @25000 and @26000 are used. * Use alias enet2 and enet3 for the remainig controllers, * to stay compatible with mpc8548si-pre.dtsi. */ enet2: ethernet@24000 { status = "disabled"; }; mdio@24520 { phy0: ethernet-phy@0 { interrupts = <7 1 0 0>; reg = <0x0>; }; phy1: ethernet-phy@1 { interrupts = <8 1 0 0>; reg = <0x1>; }; tbi0: tbi-phy@11 { reg = <0x11>; device_type = "tbi-phy"; }; }; enet0: ethernet@25000 { tbi-handle = <&tbi1>; phy-handle = <&phy0>; }; mdio@25520 { tbi1: tbi-phy@11 { reg = <0x11>; device_type = "tbi-phy"; }; }; enet1: ethernet@26000 { tbi-handle = <&tbi2>; phy-handle = <&phy1>; }; mdio@26520 { tbi2: tbi-phy@11 { reg = <0x11>; device_type = "tbi-phy"; }; }; enet3: ethernet@27000 { status = "disabled"; }; mdio@27520 { tbi3: tbi-phy@11 { reg = <0x11>; device_type = "tbi-phy"; }; }; crypto@30000 { status = "disabled"; }; }; /include/ "mpc8548si-post.dtsi" |