Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 | # SPDX-License-Identifier: GPL-2.0 config FB_OMAP2_DSS_INIT bool config FB_OMAP2_DSS tristate select VIDEOMODE_HELPERS select FB_OMAP2_DSS_INIT select HDMI config FB_OMAP2_DSS_DEBUG bool "Debug support" help This enables printing of debug messages. Alternatively, debug messages can also be enabled by setting CONFIG_DYNAMIC_DEBUG and then setting appropriate flags in <debugfs>/dynamic_debug/control. config FB_OMAP2_DSS_DEBUGFS bool "Debugfs filesystem support" depends on DEBUG_FS help This enables debugfs for OMAPDSS at <debugfs>/omapdss. This enables querying about clock configuration and register configuration of dss, dispc, dsi, hdmi and rfbi. config FB_OMAP2_DSS_COLLECT_IRQ_STATS bool "Collect DSS IRQ statistics" depends on FB_OMAP2_DSS_DEBUGFS help Collect DSS IRQ statistics, printable via debugfs. The statistics can be found from <debugfs>/omapdss/dispc_irq for DISPC interrupts, and <debugfs>/omapdss/dsi_irq for DSI interrupts. config FB_OMAP2_DSS_DPI bool "DPI support" default y help DPI Interface. This is the Parallel Display Interface. config FB_OMAP2_DSS_VENC bool "VENC support" default y help OMAP Video Encoder support for S-Video and composite TV-out. config FB_OMAP2_DSS_HDMI_COMMON bool config FB_OMAP4_DSS_HDMI bool "HDMI support for OMAP4" default y select FB_OMAP2_DSS_HDMI_COMMON help HDMI support for OMAP4 based SoCs. config FB_OMAP5_DSS_HDMI bool "HDMI support for OMAP5" select FB_OMAP2_DSS_HDMI_COMMON help HDMI Interface for OMAP5 and similar cores. This adds the High Definition Multimedia Interface. See https://www.hdmi.org/ for HDMI specification. config FB_OMAP2_DSS_SDI bool "SDI support" help SDI (Serial Display Interface) support. SDI is a high speed one-way display serial bus between the host processor and a display. config FB_OMAP2_DSS_DSI bool "DSI support" help MIPI DSI (Display Serial Interface) support. DSI is a high speed half-duplex serial interface between the host processor and a peripheral, such as a display or a framebuffer chip. See https://www.mipi.org/ for DSI specifications. config FB_OMAP2_DSS_MIN_FCK_PER_PCK int "Minimum FCK/PCK ratio (for scaling)" range 0 32 default 0 help This can be used to adjust the minimum FCK/PCK ratio. With this you can make sure that DISPC FCK is at least n x PCK. Video plane scaling requires higher FCK than normally. If this is set to 0, there's no extra constraint on the DISPC FCK. However, the FCK will at minimum be 2xPCK (if active matrix) or 3xPCK (if passive matrix). Max FCK is 173MHz, so this doesn't work if your PCK is very high. config FB_OMAP2_DSS_SLEEP_AFTER_VENC_RESET bool "Sleep 20ms after VENC reset" default y help There is a 20ms sleep after VENC reset which seemed to fix the reset. The reason for the bug is unclear, and it's also unclear on what platforms this happens. This option enables the sleep, and is enabled by default. You can disable the sleep if it doesn't cause problems on your platform. |