Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 | /* SPDX-License-Identifier: GPL-2.0-or-later */ /*------------------------------------------------------------------------ . smc91x.h - macros for SMSC's 91C9x/91C1xx single-chip Ethernet device. . . Copyright (C) 1996 by Erik Stahlman . Copyright (C) 2001 Standard Microsystems Corporation . Developed by Simple Network Magic Corporation . Copyright (C) 2003 Monta Vista Software, Inc. . Unified SMC91x driver by Nicolas Pitre . . . Information contained in this file was obtained from the LAN91C111 . manual from SMC. To get a copy, if you really want one, you can find . information under www.smsc.com. . . Authors . Erik Stahlman <erik@vt.edu> . Daris A Nevil <dnevil@snmc.com> . Nicolas Pitre <nico@fluxnic.net> . ---------------------------------------------------------------------------*/ #ifndef _SMC91X_H_ #define _SMC91X_H_ #include <linux/dmaengine.h> #include <linux/smc91x.h> /* * Any 16-bit access is performed with two 8-bit accesses if the hardware * can't do it directly. Most registers are 16-bit so those are mandatory. */ #define SMC_outw_b(x, a, r) \ do { \ unsigned int __val16 = (x); \ unsigned int __reg = (r); \ SMC_outb(__val16, a, __reg); \ SMC_outb(__val16 >> 8, a, __reg + (1 << SMC_IO_SHIFT)); \ } while (0) #define SMC_inw_b(a, r) \ ({ \ unsigned int __val16; \ unsigned int __reg = r; \ __val16 = SMC_inb(a, __reg); \ __val16 |= SMC_inb(a, __reg + (1 << SMC_IO_SHIFT)) << 8; \ __val16; \ }) /* * Define your architecture specific bus configuration parameters here. */ #if defined(CONFIG_ARM) #include <asm/mach-types.h> /* Now the bus width is specified in the platform data * pretend here to support all I/O access types */ #define SMC_CAN_USE_8BIT 1 #define SMC_CAN_USE_16BIT 1 #define SMC_CAN_USE_32BIT 1 #define SMC_NOWAIT 1 #define SMC_IO_SHIFT (lp->io_shift) #define SMC_inb(a, r) readb((a) + (r)) #define SMC_inw(a, r) \ ({ \ unsigned int __smc_r = r; \ SMC_16BIT(lp) ? readw((a) + __smc_r) : \ SMC_8BIT(lp) ? SMC_inw_b(a, __smc_r) : \ ({ BUG(); 0; }); \ }) #define SMC_inl(a, r) readl((a) + (r)) #define SMC_outb(v, a, r) writeb(v, (a) + (r)) #define SMC_outw(lp, v, a, r) \ do { \ unsigned int __v = v, __smc_r = r; \ if (SMC_16BIT(lp)) \ __SMC_outw(lp, __v, a, __smc_r); \ else if (SMC_8BIT(lp)) \ SMC_outw_b(__v, a, __smc_r); \ else \ BUG(); \ } while (0) #define SMC_outl(v, a, r) writel(v, (a) + (r)) #define SMC_insb(a, r, p, l) readsb((a) + (r), p, l) #define SMC_outsb(a, r, p, l) writesb((a) + (r), p, l) #define SMC_insw(a, r, p, l) readsw((a) + (r), p, l) #define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l) #define SMC_insl(a, r, p, l) readsl((a) + (r), p, l) #define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l) #define SMC_IRQ_FLAGS (-1) /* from resource */ /* We actually can't write halfwords properly if not word aligned */ static inline void _SMC_outw_align4(u16 val, void __iomem *ioaddr, int reg, bool use_align4_workaround) { if (use_align4_workaround) { unsigned int v = val << 16; v |= readl(ioaddr + (reg & ~2)) & 0xffff; writel(v, ioaddr + (reg & ~2)); } else { writew(val, ioaddr + reg); } } #define __SMC_outw(lp, v, a, r) \ _SMC_outw_align4((v), (a), (r), \ IS_BUILTIN(CONFIG_ARCH_PXA) && ((r) & 2) && \ (lp)->cfg.pxa_u16_align4) #elif defined(CONFIG_SH_SH4202_MICRODEV) #define SMC_CAN_USE_8BIT 0 #define SMC_CAN_USE_16BIT 1 #define SMC_CAN_USE_32BIT 0 #define SMC_inb(a, r) inb((a) + (r) - 0xa0000000) #define SMC_inw(a, r) inw((a) + (r) - 0xa0000000) #define SMC_inl(a, r) inl((a) + (r) - 0xa0000000) #define SMC_outb(v, a, r) outb(v, (a) + (r) - 0xa0000000) #define SMC_outw(lp, v, a, r) outw(v, (a) + (r) - 0xa0000000) #define SMC_outl(v, a, r) outl(v, (a) + (r) - 0xa0000000) #define SMC_insl(a, r, p, l) insl((a) + (r) - 0xa0000000, p, l) #define SMC_outsl(a, r, p, l) outsl((a) + (r) - 0xa0000000, p, l) #define SMC_insw(a, r, p, l) insw((a) + (r) - 0xa0000000, p, l) #define SMC_outsw(a, r, p, l) outsw((a) + (r) - 0xa0000000, p, l) #define SMC_IRQ_FLAGS (0) #elif defined(CONFIG_ATARI) #define SMC_CAN_USE_8BIT 1 #define SMC_CAN_USE_16BIT 1 #define SMC_CAN_USE_32BIT 1 #define SMC_NOWAIT 1 #define SMC_inb(a, r) readb((a) + (r)) #define SMC_inw(a, r) readw((a) + (r)) #define SMC_inl(a, r) readl((a) + (r)) #define SMC_outb(v, a, r) writeb(v, (a) + (r)) #define SMC_outw(lp, v, a, r) writew(v, (a) + (r)) #define SMC_outl(v, a, r) writel(v, (a) + (r)) #define SMC_insw(a, r, p, l) readsw((a) + (r), p, l) #define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l) #define SMC_insl(a, r, p, l) readsl((a) + (r), p, l) #define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l) #define RPC_LSA_DEFAULT RPC_LED_100_10 #define RPC_LSB_DEFAULT RPC_LED_TX_RX #elif defined(CONFIG_COLDFIRE) #define SMC_CAN_USE_8BIT 0 #define SMC_CAN_USE_16BIT 1 #define SMC_CAN_USE_32BIT 0 #define SMC_NOWAIT 1 static inline void mcf_insw(void *a, unsigned char *p, int l) { u16 *wp = (u16 *) p; while (l-- > 0) *wp++ = readw(a); } static inline void mcf_outsw(void *a, unsigned char *p, int l) { u16 *wp = (u16 *) p; while (l-- > 0) writew(*wp++, a); } #define SMC_inw(a, r) _swapw(readw((a) + (r))) #define SMC_outw(lp, v, a, r) writew(_swapw(v), (a) + (r)) #define SMC_insw(a, r, p, l) mcf_insw(a + r, p, l) #define SMC_outsw(a, r, p, l) mcf_outsw(a + r, p, l) #define SMC_IRQ_FLAGS 0 #elif defined(CONFIG_H8300) #define SMC_CAN_USE_8BIT 1 #define SMC_CAN_USE_16BIT 0 #define SMC_CAN_USE_32BIT 0 #define SMC_NOWAIT 0 #define SMC_inb(a, r) ioread8((a) + (r)) #define SMC_outb(v, a, r) iowrite8(v, (a) + (r)) #define SMC_insb(a, r, p, l) ioread8_rep((a) + (r), p, l) #define SMC_outsb(a, r, p, l) iowrite8_rep((a) + (r), p, l) #else /* * Default configuration */ #define SMC_CAN_USE_8BIT 1 #define SMC_CAN_USE_16BIT 1 #define SMC_CAN_USE_32BIT 1 #define SMC_NOWAIT 1 #define SMC_IO_SHIFT (lp->io_shift) #define SMC_inb(a, r) ioread8((a) + (r)) #define SMC_inw(a, r) ioread16((a) + (r)) #define SMC_inl(a, r) ioread32((a) + (r)) #define SMC_outb(v, a, r) iowrite8(v, (a) + (r)) #define SMC_outw(lp, v, a, r) iowrite16(v, (a) + (r)) #define SMC_outl(v, a, r) iowrite32(v, (a) + (r)) #define SMC_insw(a, r, p, l) ioread16_rep((a) + (r), p, l) #define SMC_outsw(a, r, p, l) iowrite16_rep((a) + (r), p, l) #define SMC_insl(a, r, p, l) ioread32_rep((a) + (r), p, l) #define SMC_outsl(a, r, p, l) iowrite32_rep((a) + (r), p, l) #define RPC_LSA_DEFAULT RPC_LED_100_10 #define RPC_LSB_DEFAULT RPC_LED_TX_RX #endif /* store this information for the driver.. */ struct smc_local { /* * If I have to wait until memory is available to send a * packet, I will store the skbuff here, until I get the * desired memory. Then, I'll send it out and free it. */ struct sk_buff *pending_tx_skb; struct tasklet_struct tx_task; struct gpio_desc *power_gpio; struct gpio_desc *reset_gpio; /* version/revision of the SMC91x chip */ int version; /* Contains the current active transmission mode */ int tcr_cur_mode; /* Contains the current active receive mode */ int rcr_cur_mode; /* Contains the current active receive/phy mode */ int rpc_cur_mode; int ctl_rfduplx; int ctl_rspeed; u32 msg_enable; u32 phy_type; struct mii_if_info mii; /* work queue */ struct work_struct phy_configure; struct net_device *dev; int work_pending; spinlock_t lock; #ifdef CONFIG_ARCH_PXA /* DMA needs the physical address of the chip */ u_long physaddr; struct device *device; #endif struct dma_chan *dma_chan; void __iomem *base; void __iomem *datacs; /* the low address lines on some platforms aren't connected... */ int io_shift; /* on some platforms a u16 write must be 4-bytes aligned */ bool half_word_align4; struct smc91x_platdata cfg; }; #define SMC_8BIT(p) ((p)->cfg.flags & SMC91X_USE_8BIT) #define SMC_16BIT(p) ((p)->cfg.flags & SMC91X_USE_16BIT) #define SMC_32BIT(p) ((p)->cfg.flags & SMC91X_USE_32BIT) #ifdef CONFIG_ARCH_PXA /* * Let's use the DMA engine on the XScale PXA2xx for RX packets. This is * always happening in irq context so no need to worry about races. TX is * different and probably not worth it for that reason, and not as critical * as RX which can overrun memory and lose packets. */ #include <linux/dma-mapping.h> #ifdef SMC_insl #undef SMC_insl #define SMC_insl(a, r, p, l) \ smc_pxa_dma_insl(a, lp, r, dev->dma, p, l) static inline void smc_pxa_dma_inpump(struct smc_local *lp, u_char *buf, int len) { dma_addr_t dmabuf; struct dma_async_tx_descriptor *tx; dma_cookie_t cookie; enum dma_status status; struct dma_tx_state state; dmabuf = dma_map_single(lp->device, buf, len, DMA_FROM_DEVICE); tx = dmaengine_prep_slave_single(lp->dma_chan, dmabuf, len, DMA_DEV_TO_MEM, 0); if (tx) { cookie = dmaengine_submit(tx); dma_async_issue_pending(lp->dma_chan); do { status = dmaengine_tx_status(lp->dma_chan, cookie, &state); cpu_relax(); } while (status != DMA_COMPLETE && status != DMA_ERROR && state.residue); dmaengine_terminate_all(lp->dma_chan); } dma_unmap_single(lp->device, dmabuf, len, DMA_FROM_DEVICE); } static inline void smc_pxa_dma_insl(void __iomem *ioaddr, struct smc_local *lp, int reg, int dma, u_char *buf, int len) { struct dma_slave_config config; int ret; /* fallback if no DMA available */ if (!lp->dma_chan) { readsl(ioaddr + reg, buf, len); return; } /* 64 bit alignment is required for memory to memory DMA */ if ((long)buf & 4) { *((u32 *)buf) = SMC_inl(ioaddr, reg); buf += 4; len--; } memset(&config, 0, sizeof(config)); config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; config.src_addr = lp->physaddr + reg; config.dst_addr = lp->physaddr + reg; config.src_maxburst = 32; config.dst_maxburst = 32; ret = dmaengine_slave_config(lp->dma_chan, &config); if (ret) { dev_err(lp->device, "dma channel configuration failed: %d\n", ret); return; } len *= 4; smc_pxa_dma_inpump(lp, buf, len); } #endif #ifdef SMC_insw #undef SMC_insw #define SMC_insw(a, r, p, l) \ smc_pxa_dma_insw(a, lp, r, dev->dma, p, l) static inline void smc_pxa_dma_insw(void __iomem *ioaddr, struct smc_local *lp, int reg, int dma, u_char *buf, int len) { struct dma_slave_config config; int ret; /* fallback if no DMA available */ if (!lp->dma_chan) { readsw(ioaddr + reg, buf, len); return; } /* 64 bit alignment is required for memory to memory DMA */ while ((long)buf & 6) { *((u16 *)buf) = SMC_inw(ioaddr, reg); buf += 2; len--; } memset(&config, 0, sizeof(config)); config.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; config.dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; config.src_addr = lp->physaddr + reg; config.dst_addr = lp->physaddr + reg; config.src_maxburst = 32; config.dst_maxburst = 32; ret = dmaengine_slave_config(lp->dma_chan, &config); if (ret) { dev_err(lp->device, "dma channel configuration failed: %d\n", ret); return; } len *= 2; smc_pxa_dma_inpump(lp, buf, len); } #endif #endif /* CONFIG_ARCH_PXA */ /* * Everything a particular hardware setup needs should have been defined * at this point. Add stubs for the undefined cases, mainly to avoid * compilation warnings since they'll be optimized away, or to prevent buggy * use of them. */ #if ! SMC_CAN_USE_32BIT #define SMC_inl(ioaddr, reg) ({ BUG(); 0; }) #define SMC_outl(x, ioaddr, reg) BUG() #define SMC_insl(a, r, p, l) BUG() #define SMC_outsl(a, r, p, l) BUG() #endif #if !defined(SMC_insl) || !defined(SMC_outsl) #define SMC_insl(a, r, p, l) BUG() #define SMC_outsl(a, r, p, l) BUG() #endif #if ! SMC_CAN_USE_16BIT #define SMC_outw(lp, x, ioaddr, reg) SMC_outw_b(x, ioaddr, reg) #define SMC_inw(ioaddr, reg) SMC_inw_b(ioaddr, reg) #define SMC_insw(a, r, p, l) BUG() #define SMC_outsw(a, r, p, l) BUG() #endif #if !defined(SMC_insw) || !defined(SMC_outsw) #define SMC_insw(a, r, p, l) BUG() #define SMC_outsw(a, r, p, l) BUG() #endif #if ! SMC_CAN_USE_8BIT #undef SMC_inb #define SMC_inb(ioaddr, reg) ({ BUG(); 0; }) #undef SMC_outb #define SMC_outb(x, ioaddr, reg) BUG() #define SMC_insb(a, r, p, l) BUG() #define SMC_outsb(a, r, p, l) BUG() #endif #if !defined(SMC_insb) || !defined(SMC_outsb) #define SMC_insb(a, r, p, l) BUG() #define SMC_outsb(a, r, p, l) BUG() #endif #ifndef SMC_CAN_USE_DATACS #define SMC_CAN_USE_DATACS 0 #endif #ifndef SMC_IO_SHIFT #define SMC_IO_SHIFT 0 #endif #ifndef SMC_IRQ_FLAGS #define SMC_IRQ_FLAGS IRQF_TRIGGER_RISING #endif #ifndef SMC_INTERRUPT_PREAMBLE #define SMC_INTERRUPT_PREAMBLE #endif /* Because of bank switching, the LAN91x uses only 16 I/O ports */ #define SMC_IO_EXTENT (16 << SMC_IO_SHIFT) #define SMC_DATA_EXTENT (4) /* . Bank Select Register: . . yyyy yyyy 0000 00xx . xx = bank number . yyyy yyyy = 0x33, for identification purposes. */ #define BANK_SELECT (14 << SMC_IO_SHIFT) // Transmit Control Register /* BANK 0 */ #define TCR_REG(lp) SMC_REG(lp, 0x0000, 0) #define TCR_ENABLE 0x0001 // When 1 we can transmit #define TCR_LOOP 0x0002 // Controls output pin LBK #define TCR_FORCOL 0x0004 // When 1 will force a collision #define TCR_PAD_EN 0x0080 // When 1 will pad tx frames < 64 bytes w/0 #define TCR_NOCRC 0x0100 // When 1 will not append CRC to tx frames #define TCR_MON_CSN 0x0400 // When 1 tx monitors carrier #define TCR_FDUPLX 0x0800 // When 1 enables full duplex operation #define TCR_STP_SQET 0x1000 // When 1 stops tx if Signal Quality Error #define TCR_EPH_LOOP 0x2000 // When 1 enables EPH block loopback #define TCR_SWFDUP 0x8000 // When 1 enables Switched Full Duplex mode #define TCR_CLEAR 0 /* do NOTHING */ /* the default settings for the TCR register : */ #define TCR_DEFAULT (TCR_ENABLE | TCR_PAD_EN) // EPH Status Register /* BANK 0 */ #define EPH_STATUS_REG(lp) SMC_REG(lp, 0x0002, 0) #define ES_TX_SUC 0x0001 // Last TX was successful #define ES_SNGL_COL 0x0002 // Single collision detected for last tx #define ES_MUL_COL 0x0004 // Multiple collisions detected for last tx #define ES_LTX_MULT 0x0008 // Last tx was a multicast #define ES_16COL 0x0010 // 16 Collisions Reached #define ES_SQET 0x0020 // Signal Quality Error Test #define ES_LTXBRD 0x0040 // Last tx was a broadcast #define ES_TXDEFR 0x0080 // Transmit Deferred #define ES_LATCOL 0x0200 // Late collision detected on last tx #define ES_LOSTCARR 0x0400 // Lost Carrier Sense #define ES_EXC_DEF 0x0800 // Excessive Deferral #define ES_CTR_ROL 0x1000 // Counter Roll Over indication #define ES_LINK_OK 0x4000 // Driven by inverted value of nLNK pin #define ES_TXUNRN 0x8000 // Tx Underrun // Receive Control Register /* BANK 0 */ #define RCR_REG(lp) SMC_REG(lp, 0x0004, 0) #define RCR_RX_ABORT 0x0001 // Set if a rx frame was aborted #define RCR_PRMS 0x0002 // Enable promiscuous mode #define RCR_ALMUL 0x0004 // When set accepts all multicast frames #define RCR_RXEN 0x0100 // IFF this is set, we can receive packets #define RCR_STRIP_CRC 0x0200 // When set strips CRC from rx packets #define RCR_ABORT_ENB 0x0200 // When set will abort rx on collision #define RCR_FILT_CAR 0x0400 // When set filters leading 12 bit s of carrier #define RCR_SOFTRST 0x8000 // resets the chip /* the normal settings for the RCR register : */ #define RCR_DEFAULT (RCR_STRIP_CRC | RCR_RXEN) #define RCR_CLEAR 0x0 // set it to a base state // Counter Register /* BANK 0 */ #define COUNTER_REG(lp) SMC_REG(lp, 0x0006, 0) // Memory Information Register /* BANK 0 */ #define MIR_REG(lp) SMC_REG(lp, 0x0008, 0) // Receive/Phy Control Register /* BANK 0 */ #define RPC_REG(lp) SMC_REG(lp, 0x000A, 0) #define RPC_SPEED 0x2000 // When 1 PHY is in 100Mbps mode. #define RPC_DPLX 0x1000 // When 1 PHY is in Full-Duplex Mode #define RPC_ANEG 0x0800 // When 1 PHY is in Auto-Negotiate Mode #define RPC_LSXA_SHFT 5 // Bits to shift LS2A,LS1A,LS0A to lsb #define RPC_LSXB_SHFT 2 // Bits to get LS2B,LS1B,LS0B to lsb #ifndef RPC_LSA_DEFAULT #define RPC_LSA_DEFAULT RPC_LED_100 #endif #ifndef RPC_LSB_DEFAULT #define RPC_LSB_DEFAULT RPC_LED_FD #endif #define RPC_DEFAULT (RPC_ANEG | RPC_SPEED | RPC_DPLX) /* Bank 0 0x0C is reserved */ // Bank Select Register /* All Banks */ #define BSR_REG 0x000E // Configuration Reg /* BANK 1 */ #define CONFIG_REG(lp) SMC_REG(lp, 0x0000, 1) #define CONFIG_EXT_PHY 0x0200 // 1=external MII, 0=internal Phy #define CONFIG_GPCNTRL 0x0400 // Inverse value drives pin nCNTRL #define CONFIG_NO_WAIT 0x1000 // When 1 no extra wait states on ISA bus #define CONFIG_EPH_POWER_EN 0x8000 // When 0 EPH is placed into low power mode. // Default is powered-up, Internal Phy, Wait States, and pin nCNTRL=low #define CONFIG_DEFAULT (CONFIG_EPH_POWER_EN) // Base Address Register /* BANK 1 */ #define BASE_REG(lp) SMC_REG(lp, 0x0002, 1) // Individual Address Registers /* BANK 1 */ #define ADDR0_REG(lp) SMC_REG(lp, 0x0004, 1) #define ADDR1_REG(lp) SMC_REG(lp, 0x0006, 1) #define ADDR2_REG(lp) SMC_REG(lp, 0x0008, 1) // General Purpose Register /* BANK 1 */ #define GP_REG(lp) SMC_REG(lp, 0x000A, 1) // Control Register /* BANK 1 */ #define CTL_REG(lp) SMC_REG(lp, 0x000C, 1) #define CTL_RCV_BAD 0x4000 // When 1 bad CRC packets are received #define CTL_AUTO_RELEASE 0x0800 // When 1 tx pages are released automatically #define CTL_LE_ENABLE 0x0080 // When 1 enables Link Error interrupt #define CTL_CR_ENABLE 0x0040 // When 1 enables Counter Rollover interrupt #define CTL_TE_ENABLE 0x0020 // When 1 enables Transmit Error interrupt #define CTL_EEPROM_SELECT 0x0004 // Controls EEPROM reload & store #define CTL_RELOAD 0x0002 // When set reads EEPROM into registers #define CTL_STORE 0x0001 // When set stores registers into EEPROM // MMU Command Register /* BANK 2 */ #define MMU_CMD_REG(lp) SMC_REG(lp, 0x0000, 2) #define MC_BUSY 1 // When 1 the last release has not completed #define MC_NOP (0<<5) // No Op #define MC_ALLOC (1<<5) // OR with number of 256 byte packets #define MC_RESET (2<<5) // Reset MMU to initial state #define MC_REMOVE (3<<5) // Remove the current rx packet #define MC_RELEASE (4<<5) // Remove and release the current rx packet #define MC_FREEPKT (5<<5) // Release packet in PNR register #define MC_ENQUEUE (6<<5) // Enqueue the packet for transmit #define MC_RSTTXFIFO (7<<5) // Reset the TX FIFOs // Packet Number Register /* BANK 2 */ #define PN_REG(lp) SMC_REG(lp, 0x0002, 2) // Allocation Result Register /* BANK 2 */ #define AR_REG(lp) SMC_REG(lp, 0x0003, 2) #define AR_FAILED 0x80 // Alocation Failed // TX FIFO Ports Register /* BANK 2 */ #define TXFIFO_REG(lp) SMC_REG(lp, 0x0004, 2) #define TXFIFO_TEMPTY 0x80 // TX FIFO Empty // RX FIFO Ports Register /* BANK 2 */ #define RXFIFO_REG(lp) SMC_REG(lp, 0x0005, 2) #define RXFIFO_REMPTY 0x80 // RX FIFO Empty #define FIFO_REG(lp) SMC_REG(lp, 0x0004, 2) // Pointer Register /* BANK 2 */ #define PTR_REG(lp) SMC_REG(lp, 0x0006, 2) #define PTR_RCV 0x8000 // 1=Receive area, 0=Transmit area #define PTR_AUTOINC 0x4000 // Auto increment the pointer on each access #define PTR_READ 0x2000 // When 1 the operation is a read // Data Register /* BANK 2 */ #define DATA_REG(lp) SMC_REG(lp, 0x0008, 2) // Interrupt Status/Acknowledge Register /* BANK 2 */ #define INT_REG(lp) SMC_REG(lp, 0x000C, 2) // Interrupt Mask Register /* BANK 2 */ #define IM_REG(lp) SMC_REG(lp, 0x000D, 2) #define IM_MDINT 0x80 // PHY MI Register 18 Interrupt #define IM_ERCV_INT 0x40 // Early Receive Interrupt #define IM_EPH_INT 0x20 // Set by Ethernet Protocol Handler section #define IM_RX_OVRN_INT 0x10 // Set by Receiver Overruns #define IM_ALLOC_INT 0x08 // Set when allocation request is completed #define IM_TX_EMPTY_INT 0x04 // Set if the TX FIFO goes empty #define IM_TX_INT 0x02 // Transmit Interrupt #define IM_RCV_INT 0x01 // Receive Interrupt // Multicast Table Registers /* BANK 3 */ #define MCAST_REG1(lp) SMC_REG(lp, 0x0000, 3) #define MCAST_REG2(lp) SMC_REG(lp, 0x0002, 3) #define MCAST_REG3(lp) SMC_REG(lp, 0x0004, 3) #define MCAST_REG4(lp) SMC_REG(lp, 0x0006, 3) // Management Interface Register (MII) /* BANK 3 */ #define MII_REG(lp) SMC_REG(lp, 0x0008, 3) #define MII_MSK_CRS100 0x4000 // Disables CRS100 detection during tx half dup #define MII_MDOE 0x0008 // MII Output Enable #define MII_MCLK 0x0004 // MII Clock, pin MDCLK #define MII_MDI 0x0002 // MII Input, pin MDI #define MII_MDO 0x0001 // MII Output, pin MDO // Revision Register /* BANK 3 */ /* ( hi: chip id low: rev # ) */ #define REV_REG(lp) SMC_REG(lp, 0x000A, 3) // Early RCV Register /* BANK 3 */ /* this is NOT on SMC9192 */ #define ERCV_REG(lp) SMC_REG(lp, 0x000C, 3) #define ERCV_RCV_DISCRD 0x0080 // When 1 discards a packet being received #define ERCV_THRESHOLD 0x001F // ERCV Threshold Mask // External Register /* BANK 7 */ #define EXT_REG(lp) SMC_REG(lp, 0x0000, 7) #define CHIP_9192 3 #define CHIP_9194 4 #define CHIP_9195 5 #define CHIP_9196 6 #define CHIP_91100 7 #define CHIP_91100FD 8 #define CHIP_91111FD 9 static const char * chip_ids[ 16 ] = { NULL, NULL, NULL, /* 3 */ "SMC91C90/91C92", /* 4 */ "SMC91C94", /* 5 */ "SMC91C95", /* 6 */ "SMC91C96", /* 7 */ "SMC91C100", /* 8 */ "SMC91C100FD", /* 9 */ "SMC91C11xFD", NULL, NULL, NULL, NULL, NULL, NULL}; /* . Receive status bits */ #define RS_ALGNERR 0x8000 #define RS_BRODCAST 0x4000 #define RS_BADCRC 0x2000 #define RS_ODDFRAME 0x1000 #define RS_TOOLONG 0x0800 #define RS_TOOSHORT 0x0400 #define RS_MULTICAST 0x0001 #define RS_ERRORS (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT) /* * PHY IDs * LAN83C183 == LAN91C111 Internal PHY */ #define PHY_LAN83C183 0x0016f840 #define PHY_LAN83C180 0x02821c50 /* * PHY Register Addresses (LAN91C111 Internal PHY) * * Generic PHY registers can be found in <linux/mii.h> * * These phy registers are specific to our on-board phy. */ // PHY Configuration Register 1 #define PHY_CFG1_REG 0x10 #define PHY_CFG1_LNKDIS 0x8000 // 1=Rx Link Detect Function disabled #define PHY_CFG1_XMTDIS 0x4000 // 1=TP Transmitter Disabled #define PHY_CFG1_XMTPDN 0x2000 // 1=TP Transmitter Powered Down #define PHY_CFG1_BYPSCR 0x0400 // 1=Bypass scrambler/descrambler #define PHY_CFG1_UNSCDS 0x0200 // 1=Unscramble Idle Reception Disable #define PHY_CFG1_EQLZR 0x0100 // 1=Rx Equalizer Disabled #define PHY_CFG1_CABLE 0x0080 // 1=STP(150ohm), 0=UTP(100ohm) #define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db #define PHY_CFG1_TLVL_SHIFT 2 // Transmit Output Level Adjust #define PHY_CFG1_TLVL_MASK 0x003C #define PHY_CFG1_TRF_MASK 0x0003 // Transmitter Rise/Fall time // PHY Configuration Register 2 #define PHY_CFG2_REG 0x11 #define PHY_CFG2_APOLDIS 0x0020 // 1=Auto Polarity Correction disabled #define PHY_CFG2_JABDIS 0x0010 // 1=Jabber disabled #define PHY_CFG2_MREG 0x0008 // 1=Multiple register access (MII mgt) #define PHY_CFG2_INTMDIO 0x0004 // 1=Interrupt signaled with MDIO pulseo // PHY Status Output (and Interrupt status) Register #define PHY_INT_REG 0x12 // Status Output (Interrupt Status) #define PHY_INT_INT 0x8000 // 1=bits have changed since last read #define PHY_INT_LNKFAIL 0x4000 // 1=Link Not detected #define PHY_INT_LOSSSYNC 0x2000 // 1=Descrambler has lost sync #define PHY_INT_CWRD 0x1000 // 1=Invalid 4B5B code detected on rx #define PHY_INT_SSD 0x0800 // 1=No Start Of Stream detected on rx #define PHY_INT_ESD 0x0400 // 1=No End Of Stream detected on rx #define PHY_INT_RPOL 0x0200 // 1=Reverse Polarity detected #define PHY_INT_JAB 0x0100 // 1=Jabber detected #define PHY_INT_SPDDET 0x0080 // 1=100Base-TX mode, 0=10Base-T mode #define PHY_INT_DPLXDET 0x0040 // 1=Device in Full Duplex // PHY Interrupt/Status Mask Register #define PHY_MASK_REG 0x13 // Interrupt Mask // Uses the same bit definitions as PHY_INT_REG /* * SMC91C96 ethernet config and status registers. * These are in the "attribute" space. */ #define ECOR 0x8000 #define ECOR_RESET 0x80 #define ECOR_LEVEL_IRQ 0x40 #define ECOR_WR_ATTRIB 0x04 #define ECOR_ENABLE 0x01 #define ECSR 0x8002 #define ECSR_IOIS8 0x20 #define ECSR_PWRDWN 0x04 #define ECSR_INT 0x02 #define ATTRIB_SIZE ((64*1024) << SMC_IO_SHIFT) /* * Macros to abstract register access according to the data bus * capabilities. Please use those and not the in/out primitives. * Note: the following macros do *not* select the bank -- this must * be done separately as needed in the main code. The SMC_REG() macro * only uses the bank argument for debugging purposes (when enabled). * * Note: despite inline functions being safer, everything leading to this * should preferably be macros to let BUG() display the line number in * the core source code since we're interested in the top call site * not in any inline function location. */ #if SMC_DEBUG > 0 #define SMC_REG(lp, reg, bank) \ ({ \ int __b = SMC_CURRENT_BANK(lp); \ if (unlikely((__b & ~0xf0) != (0x3300 | bank))) { \ pr_err("%s: bank reg screwed (0x%04x)\n", \ CARDNAME, __b); \ BUG(); \ } \ reg<<SMC_IO_SHIFT; \ }) #else #define SMC_REG(lp, reg, bank) (reg<<SMC_IO_SHIFT) #endif /* * Hack Alert: Some setups just can't write 8 or 16 bits reliably when not * aligned to a 32 bit boundary. I tell you that does exist! * Fortunately the affected register accesses can be easily worked around * since we can write zeroes to the preceding 16 bits without adverse * effects and use a 32-bit access. * * Enforce it on any 32-bit capable setup for now. */ #define SMC_MUST_ALIGN_WRITE(lp) SMC_32BIT(lp) #define SMC_GET_PN(lp) \ (SMC_8BIT(lp) ? (SMC_inb(ioaddr, PN_REG(lp))) \ : (SMC_inw(ioaddr, PN_REG(lp)) & 0xFF)) #define SMC_SET_PN(lp, x) \ do { \ if (SMC_MUST_ALIGN_WRITE(lp)) \ SMC_outl((x)<<16, ioaddr, SMC_REG(lp, 0, 2)); \ else if (SMC_8BIT(lp)) \ SMC_outb(x, ioaddr, PN_REG(lp)); \ else \ SMC_outw(lp, x, ioaddr, PN_REG(lp)); \ } while (0) #define SMC_GET_AR(lp) \ (SMC_8BIT(lp) ? (SMC_inb(ioaddr, AR_REG(lp))) \ : (SMC_inw(ioaddr, PN_REG(lp)) >> 8)) #define SMC_GET_TXFIFO(lp) \ (SMC_8BIT(lp) ? (SMC_inb(ioaddr, TXFIFO_REG(lp))) \ : (SMC_inw(ioaddr, TXFIFO_REG(lp)) & 0xFF)) #define SMC_GET_RXFIFO(lp) \ (SMC_8BIT(lp) ? (SMC_inb(ioaddr, RXFIFO_REG(lp))) \ : (SMC_inw(ioaddr, TXFIFO_REG(lp)) >> 8)) #define SMC_GET_INT(lp) \ (SMC_8BIT(lp) ? (SMC_inb(ioaddr, INT_REG(lp))) \ : (SMC_inw(ioaddr, INT_REG(lp)) & 0xFF)) #define SMC_ACK_INT(lp, x) \ do { \ if (SMC_8BIT(lp)) \ SMC_outb(x, ioaddr, INT_REG(lp)); \ else { \ unsigned long __flags; \ int __mask; \ local_irq_save(__flags); \ __mask = SMC_inw(ioaddr, INT_REG(lp)) & ~0xff; \ SMC_outw(lp, __mask | (x), ioaddr, INT_REG(lp)); \ local_irq_restore(__flags); \ } \ } while (0) #define SMC_GET_INT_MASK(lp) \ (SMC_8BIT(lp) ? (SMC_inb(ioaddr, IM_REG(lp))) \ : (SMC_inw(ioaddr, INT_REG(lp)) >> 8)) #define SMC_SET_INT_MASK(lp, x) \ do { \ if (SMC_8BIT(lp)) \ SMC_outb(x, ioaddr, IM_REG(lp)); \ else \ SMC_outw(lp, (x) << 8, ioaddr, INT_REG(lp)); \ } while (0) #define SMC_CURRENT_BANK(lp) SMC_inw(ioaddr, BANK_SELECT) #define SMC_SELECT_BANK(lp, x) \ do { \ if (SMC_MUST_ALIGN_WRITE(lp)) \ SMC_outl((x)<<16, ioaddr, 12<<SMC_IO_SHIFT); \ else \ SMC_outw(lp, x, ioaddr, BANK_SELECT); \ } while (0) #define SMC_GET_BASE(lp) SMC_inw(ioaddr, BASE_REG(lp)) #define SMC_SET_BASE(lp, x) SMC_outw(lp, x, ioaddr, BASE_REG(lp)) #define SMC_GET_CONFIG(lp) SMC_inw(ioaddr, CONFIG_REG(lp)) #define SMC_SET_CONFIG(lp, x) SMC_outw(lp, x, ioaddr, CONFIG_REG(lp)) #define SMC_GET_COUNTER(lp) SMC_inw(ioaddr, COUNTER_REG(lp)) #define SMC_GET_CTL(lp) SMC_inw(ioaddr, CTL_REG(lp)) #define SMC_SET_CTL(lp, x) SMC_outw(lp, x, ioaddr, CTL_REG(lp)) #define SMC_GET_MII(lp) SMC_inw(ioaddr, MII_REG(lp)) #define SMC_GET_GP(lp) SMC_inw(ioaddr, GP_REG(lp)) #define SMC_SET_GP(lp, x) \ do { \ if (SMC_MUST_ALIGN_WRITE(lp)) \ SMC_outl((x)<<16, ioaddr, SMC_REG(lp, 8, 1)); \ else \ SMC_outw(lp, x, ioaddr, GP_REG(lp)); \ } while (0) #define SMC_SET_MII(lp, x) SMC_outw(lp, x, ioaddr, MII_REG(lp)) #define SMC_GET_MIR(lp) SMC_inw(ioaddr, MIR_REG(lp)) #define SMC_SET_MIR(lp, x) SMC_outw(lp, x, ioaddr, MIR_REG(lp)) #define SMC_GET_MMU_CMD(lp) SMC_inw(ioaddr, MMU_CMD_REG(lp)) #define SMC_SET_MMU_CMD(lp, x) SMC_outw(lp, x, ioaddr, MMU_CMD_REG(lp)) #define SMC_GET_FIFO(lp) SMC_inw(ioaddr, FIFO_REG(lp)) #define SMC_GET_PTR(lp) SMC_inw(ioaddr, PTR_REG(lp)) #define SMC_SET_PTR(lp, x) \ do { \ if (SMC_MUST_ALIGN_WRITE(lp)) \ SMC_outl((x)<<16, ioaddr, SMC_REG(lp, 4, 2)); \ else \ SMC_outw(lp, x, ioaddr, PTR_REG(lp)); \ } while (0) #define SMC_GET_EPH_STATUS(lp) SMC_inw(ioaddr, EPH_STATUS_REG(lp)) #define SMC_GET_RCR(lp) SMC_inw(ioaddr, RCR_REG(lp)) #define SMC_SET_RCR(lp, x) SMC_outw(lp, x, ioaddr, RCR_REG(lp)) #define SMC_GET_REV(lp) SMC_inw(ioaddr, REV_REG(lp)) #define SMC_GET_RPC(lp) SMC_inw(ioaddr, RPC_REG(lp)) #define SMC_SET_RPC(lp, x) \ do { \ if (SMC_MUST_ALIGN_WRITE(lp)) \ SMC_outl((x)<<16, ioaddr, SMC_REG(lp, 8, 0)); \ else \ SMC_outw(lp, x, ioaddr, RPC_REG(lp)); \ } while (0) #define SMC_GET_TCR(lp) SMC_inw(ioaddr, TCR_REG(lp)) #define SMC_SET_TCR(lp, x) SMC_outw(lp, x, ioaddr, TCR_REG(lp)) #ifndef SMC_GET_MAC_ADDR #define SMC_GET_MAC_ADDR(lp, addr) \ do { \ unsigned int __v; \ __v = SMC_inw(ioaddr, ADDR0_REG(lp)); \ addr[0] = __v; addr[1] = __v >> 8; \ __v = SMC_inw(ioaddr, ADDR1_REG(lp)); \ addr[2] = __v; addr[3] = __v >> 8; \ __v = SMC_inw(ioaddr, ADDR2_REG(lp)); \ addr[4] = __v; addr[5] = __v >> 8; \ } while (0) #endif #define SMC_SET_MAC_ADDR(lp, addr) \ do { \ SMC_outw(lp, addr[0] | (addr[1] << 8), ioaddr, ADDR0_REG(lp)); \ SMC_outw(lp, addr[2] | (addr[3] << 8), ioaddr, ADDR1_REG(lp)); \ SMC_outw(lp, addr[4] | (addr[5] << 8), ioaddr, ADDR2_REG(lp)); \ } while (0) #define SMC_SET_MCAST(lp, x) \ do { \ const unsigned char *mt = (x); \ SMC_outw(lp, mt[0] | (mt[1] << 8), ioaddr, MCAST_REG1(lp)); \ SMC_outw(lp, mt[2] | (mt[3] << 8), ioaddr, MCAST_REG2(lp)); \ SMC_outw(lp, mt[4] | (mt[5] << 8), ioaddr, MCAST_REG3(lp)); \ SMC_outw(lp, mt[6] | (mt[7] << 8), ioaddr, MCAST_REG4(lp)); \ } while (0) #define SMC_PUT_PKT_HDR(lp, status, length) \ do { \ if (SMC_32BIT(lp)) \ SMC_outl((status) | (length)<<16, ioaddr, \ DATA_REG(lp)); \ else { \ SMC_outw(lp, status, ioaddr, DATA_REG(lp)); \ SMC_outw(lp, length, ioaddr, DATA_REG(lp)); \ } \ } while (0) #define SMC_GET_PKT_HDR(lp, status, length) \ do { \ if (SMC_32BIT(lp)) { \ unsigned int __val = SMC_inl(ioaddr, DATA_REG(lp)); \ (status) = __val & 0xffff; \ (length) = __val >> 16; \ } else { \ (status) = SMC_inw(ioaddr, DATA_REG(lp)); \ (length) = SMC_inw(ioaddr, DATA_REG(lp)); \ } \ } while (0) #define SMC_PUSH_DATA(lp, p, l) \ do { \ if (SMC_32BIT(lp)) { \ void *__ptr = (p); \ int __len = (l); \ void __iomem *__ioaddr = ioaddr; \ if (__len >= 2 && (unsigned long)__ptr & 2) { \ __len -= 2; \ SMC_outsw(ioaddr, DATA_REG(lp), __ptr, 1); \ __ptr += 2; \ } \ if (SMC_CAN_USE_DATACS && lp->datacs) \ __ioaddr = lp->datacs; \ SMC_outsl(__ioaddr, DATA_REG(lp), __ptr, __len>>2); \ if (__len & 2) { \ __ptr += (__len & ~3); \ SMC_outsw(ioaddr, DATA_REG(lp), __ptr, 1); \ } \ } else if (SMC_16BIT(lp)) \ SMC_outsw(ioaddr, DATA_REG(lp), p, (l) >> 1); \ else if (SMC_8BIT(lp)) \ SMC_outsb(ioaddr, DATA_REG(lp), p, l); \ } while (0) #define SMC_PULL_DATA(lp, p, l) \ do { \ if (SMC_32BIT(lp)) { \ void *__ptr = (p); \ int __len = (l); \ void __iomem *__ioaddr = ioaddr; \ if ((unsigned long)__ptr & 2) { \ /* \ * We want 32bit alignment here. \ * Since some buses perform a full \ * 32bit fetch even for 16bit data \ * we can't use SMC_inw() here. \ * Back both source (on-chip) and \ * destination pointers of 2 bytes. \ * This is possible since the call to \ * SMC_GET_PKT_HDR() already advanced \ * the source pointer of 4 bytes, and \ * the skb_reserve(skb, 2) advanced \ * the destination pointer of 2 bytes. \ */ \ __ptr -= 2; \ __len += 2; \ SMC_SET_PTR(lp, \ 2|PTR_READ|PTR_RCV|PTR_AUTOINC); \ } \ if (SMC_CAN_USE_DATACS && lp->datacs) \ __ioaddr = lp->datacs; \ __len += 2; \ SMC_insl(__ioaddr, DATA_REG(lp), __ptr, __len>>2); \ } else if (SMC_16BIT(lp)) \ SMC_insw(ioaddr, DATA_REG(lp), p, (l) >> 1); \ else if (SMC_8BIT(lp)) \ SMC_insb(ioaddr, DATA_REG(lp), p, l); \ } while (0) #endif /* _SMC91X_H_ */ |