Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 | /* $Id: indyIRQ.S,v 1.3 1998/05/01 01:35:14 ralf Exp $ * indyIRQ.S: Interrupt exception dispatch code for FullHouse and * Guiness. * * Copyright (C) 1996 David S. Miller (dm@engr.sgi.com) */ #include <asm/asm.h> #include <asm/mipsconfig.h> #include <asm/mipsregs.h> #include <asm/regdef.h> #include <asm/stackframe.h> /* A lot of complication here is taken away because: * * 1) We handle one interrupt and return, sitting in a loop * and moving across all the pending IRQ bits in the cause * register is _NOT_ the answer, the common case is one * pending IRQ so optimize in that direction. * * 2) We need not check against bits in the status register * IRQ mask, that would make this routine slow as hell. * * 3) Linux only thinks in terms of all IRQs on or all IRQs * off, nothing in between like BSD spl() brain-damage. * * Furthermore, the IRQs on the INDY look basically (barring * software IRQs which we don't use at all) like: * * MIPS IRQ Source * -------- ------ * 0 Software (ignored) * 1 Software (ignored) * 2 Local IRQ level zero * 3 Local IRQ level one * 4 8254 Timer zero * 5 8254 Timer one * 6 Bus Error * 7 R4k timer (what we use) * * We handle the IRQ according to _our_ priority which is: * * Highest ---- R4k Timer * Local IRQ zero * Local IRQ one * Bus Error * 8254 Timer zero * Lowest ---- 8254 Timer one * * then we just return, if multiple IRQs are pending then * we will just take another exception, big deal. */ .text .set noreorder .set noat .align 5 NESTED(indyIRQ, PT_SIZE, sp) SAVE_ALL CLI .set at mfc0 s0, CP0_CAUSE # get irq mask /* First we check for r4k counter/timer IRQ. */ andi a0, s0, CAUSEF_IP7 beq a0, zero, 1f andi a0, s0, CAUSEF_IP2 # delay slot, check local level zero /* Wheee, a timer interrupt. */ move a0, sp jal indy_timer_interrupt nop # delay slot j ret_from_irq nop # delay slot 1: beq a0, zero, 1f andi a0, s0, CAUSEF_IP3 # delay slot, check local level one /* Wheee, local level zero interrupt. */ jal indy_local0_irqdispatch move a0, sp # delay slot j ret_from_irq nop # delay slot 1: beq a0, zero, 1f andi a0, s0, CAUSEF_IP6 # delay slot, check bus error /* Wheee, local level one interrupt. */ move a0, sp jal indy_local1_irqdispatch nop j ret_from_irq nop 1: beq a0, zero, 1f nop /* Wheee, an asynchronous bus error... */ move a0, sp jal indy_buserror_irq nop j ret_from_irq nop 1: /* Here by mistake? This is possible, what can happen * is that by the time we take the exception the IRQ * pin goes low, so just leave if this is the case. */ andi a0, s0, (CAUSEF_IP4 | CAUSEF_IP5) beq a0, zero, 1f /* Must be one of the 8254 timers... */ move a0, sp jal indy_8254timer_irq nop 1: j ret_from_irq nop END(indyIRQ) |